|
| 1 | SH:I:-Foundation & Sub Structure work |
| 2 | Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material Ordinary soil, Mechanical MeansAbove 6 m depth (with de-watering) |
| 3 | Ordinary rock (not requiring blasting, Mechanical MeansDepth upto 3 m ( with de-watering). |
| 4 | Stone masonry work in cement mortar 1:3 in foundation complete as per drawing and Technical SpecificationSquare Rubble Coursed rubble masonry( first sort ) |
| 5 | Plain/Reinforced Cement Concrete in Open Foundation complete as per Drawing and Technical Specifications. Using Concrete Mixer PCC Grade M15 |
| 6 | Plain/Reinforced Cement Concrete in Open Foundation complete as per Drawing and Technical Specifications. Using Concrete Mixer. RCC Grade M30 |
| 7 | Supplying, fitting and placing un-coated Mild steel reinforcement complete in foundation as per drawing and technical specification |
| 8 | Plain/Reinforced cement concrete in sub-structure complete as per drawing and technical specifications , Height 5m to 10m , Using concrete Mixer RCC Grade M30 |
| 9 | Supplying, fitting and placing Mild steel reinforcement complete in sub-structure as per drawing and technical specification. |
| 10 | Provididng weep holes in brick masonry/plain/ reinforcement concrete abutment, wing wall/ return wall with 100 mm dia AC Pipe extending through the full width of the structure with slope of 1V:20H towards drwaing face, complete as per drawing and technical specification. |
| 11 | Back filling behind the abutment, wing wall & return wall complete as per drawing and technical specificationGranular materials |
| 12 | Providing and laying of filter media with granular materials/stone crushed aggregates satisfying the requirements laid down in cluase 2504.2.2 of MoRTH specifications to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and provided over the entire surface behind abutment, wing wall and return wall to the full height compacted to a firm condition complete as per drawing and technical specification |
| 13 | Approach wallEarth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material Ordinary soil, Mechanical MeansAbove 6 m depth (with de-watering) |
| 14 | Stone masonry work in cement mortar 1:3 in foundation complete as per drawing and Technical SpecificationSquare Rubble Coursed rubble masonry( first sort ) |
| 15 | Plain/Reinforced Cement Concrete in Open Foundation complete as per Drawing and Technical Specifications.Using Concrete Mixer PCC Grade M-15 |
| 16 | Plain/Reinforced Cement Concrete in Open Foundation complete as per Drawing and Technical Specifications.Using Concrete Mixer RCC Grade M30 |
| 17 | Supplying, fitting and placing un-coated Mild steel reinforcement complete in foundation as per drawing and technical specification |
| 18 | Provididng weep holes in brick masonry/plain/ reinforcement concrete abutment, wing wall/ return wall with 100 mm dia AC Pipe extending through the full width of the structure with slope of 1V:20H towards drwaing face, complete as per drawing and technical specification. |
| 19 | Providing and laying of filter media with granular materials/stone crushed aggregates satisfying the requirements laid down in cluase 2504.2.2 of MoRTH specifications to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and provided over the entire surface behind abutment, wing wall and return wall to the full height compacted to a firm condition complete as per drawing and technical specification |
| 20 | SH:II-Steel Girder Composite Bridge |
| 21 | Supply and fabrication of steel work at Fabricators work shop comprising of Main Girders, Cross Girders, Connecting plates, stringers, stiffening plates etc. from steel plates and structural steel of specified grades as per approved drawing including straightening, descaling, degreasing, cutting to size and shape, drilling, welding and grinding, supply of all MS / HTS shop or site bolts, nuts & washers, holding down bolts and nuts etc., trial assembling at workshop, one priming coat of shop paint with red lead paint conforming to IS-102 with all labour, material, cost of paints, consumables, stacking in protected condition etc complete as per specification and as directed by the Engineer in charge (Carriage cost from fabricator workshop to actual bridge site will be paid separately). |
| 22 | Taking delivery of fabricated steel work from stacks at site as necessary, assembling and erection at site as necessary, assembling and erection of fabricated steel structure to proper line, level and camber as per approved drawings complete in asll respect including transportation and handling supply of all fasteners. Painting of all exposed surfaces of steel work after erection with one coat of red lead conforming to IS-102 and two coats Aluminium paint to IS-2339, grouting of anchor bolts in position, including all labour, consumables, materials, machinery, tools and tackles complete as per specification and as directed by the Engineer in charge |
| 23 | Cost of transportation of fabricated steel (Bridge component) complete as per specification and as directed by the Engineer in charge. |
| 24 | Decking slabFurnishing and Placing Reinforced/ Prestressed cement concrete in super-structure as per drawing and Technical SpecificationRCC/PSC Grade M35, Using Concrete Mixer, For solid slab super-structure, 18-28% of (a+b+c) ,Height 5m to 10m. |
| 25 | Supplying, fitting, and placing HYSD bar reinforcement in superstructure complete as per drawing and technical specifications Clauses 1002, 1010 and 1202. |
| 26 | Mastic Asphalt (Providing and laying 12 mm thick mastic asphalt wearing course on top of deck slab excluding prime coat with paving grade bitumen meeting the requirements given in table 500-29, prepared by using mastic cooker and laid to required level and slope after cleaning the surface, including providing antiskid surface with bitumen precoated fine grained hard stone chipping of 9.5 mm nominal size at the rate of 0.005cum per 10 sqm and at an approximate spacing of 10 cm center to center in both directions, pressed into surface when the temperature of surfaces not less than 100 deg. C, protruding 1 mm to 4 mm over mastic surface, all complete as per clause 515.) |
| 27 | Drainage spouts complete as per drawing and technical specifications Clause 1209. |
| 28 | Elastomeric Slab Steel Expansion Joint (Providing and laying of an elastomeric slab steel expansion joint, catering to right or skew (less than 20 deg., moderately curved with maximum horizontal movement upto 50 mm, complete as per approved drawings and standard specifications to be installed by the anufacturer/supplier or their authorised representative ensuring compliance to the manufacturer's instructions for installation and clause 2606 of MoRTH specifications for road & bridge works.) |
| 29 | Steel work in single section including cutting, hoisting, fixing in position and applying a priming coat of red lead paint.In Tees, Angles and Channels. |
| 30 | Supplying, fitting and fixing in position true to line and level cast steel rocker bearing conforming to IRC: 83(Pt.-1) section IX and clause 2003 of MoRTH specifications complete including all accessories as per drawing and Technical Specifications.Roller Bearing : 3x200 |
| 31 | Rocker Bearing : 3x200 |
| 32 | PCC M15 Grade leveling course below approach slab complete as per drawing and Technical specification |
| 33 | Reinforced cement concrete approach slab including reinforcement and form work complete as per drawing and Technical specification |
| 34 | Reinforced Cement Concrete Crash Barrier (Provision of an Reinforced cement concrete crash barrier at the edges of the road, approaches to bridge structures and medians, constructed with M-20 grade concrete with HYSD reinforcement conforming to IRC:21 and dowel bars 25 mm dia, 450 mm long at expansion joints filled with pre-moulded asphalt filler board, keyed to the structure on which it is built and installed as per design given in the enclosure to MOST circular No. RW/NH - 33022/1/94-DO III dated 24 June 1994 as per dimensions in the approved drawing and at locations directed by the Engineer, all as specified) M 20 grade concrete. |
| 35 | Metal Beam Crash BarrierType - B, \\"THRIE\\" : Metal Beam Crash Barrier (Providing and erecting a \\"Thrie\\" metal beam crash barrier comprising of 3 mm thick corrugated sheet metal beam rail, 85 cm above road/ground level, fixed on ISMC series channel vertical post, 150 x 75 x 5 mm spaced 2 m centre to centre, 2 m high with 1.15 m below ground level, all steel parts and fitments to be galvanised by hot dip process, all fittings to conform to IS:1367 and IS:1364, metal beam rail to be fixed on the vertical post with a space of channel section 150 x 75 x 5 mm, 546 mm long complete as per clause 810) |
| 36 | Painting on concrete surface : Providing and applying 2 coats of water based cement paint to unplastered concrete surface after cleaning the surface of dirt, dust, oil, grease, efflorescence and applying paint @ of 1 litre for 2 sqm. |
| 37 | Strip Seal Expansion Joint : Providing and laying of a strip seal expansion joint catering to maximum horizontal movement upto 70 mm, complete as per approved drawings and standard specifications to be installed by the manufacturer/supplier or their authorised representative ensuring compliance to the manufacturer's instructions for installation. |
| 38 | Sub Soil Investigation & Load TestingCost of transportation of planks, equipments and personal effects to the side of work and back as per the mobilization. |
| 39 | Boring drilling hole at the abuitments , anchor block in river banks though allkind of soil and rock up to depth of 20 mtr from the ground level (50mmdia). |
| 40 | Collection of soil sample and conducting of selection soil and rock samples to natural moisture content, particle size distribution, liquid and plastic limit, bulk and dry density and specific gravity of soil sample. |
| 41 | Completion of laboratory test result including preparation and submission of report. |
| 42 | Load Testing of Super structure of bridge after completion in all respect using static loading method to determine accpectance criteria of design as per IRC:SP:51-2015 complete as per direction of Engineer- In-Charge. |
| 43 | SH:III-Bank Protection |
| 44 | Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved materialManual Means.Depth upto 3 m. |
| 45 | Plain cement concrete 1:3:6 nominal mix in foundation with crushed stone aggregate 40 mm nominal size mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days. |
| 46 | Boulder apron laid in wire crates (Providing and laying of boulder apron laid in wire crates made with 4mm dia GI wire conforming to IS: 280 & IS:4826 in 100mm x 100mm mesh (weaved diagonally) including 10% extra for laps and joints laid with stone boulders weighing not less than 40 kg each.) Please Enable Macros to View BoQ information |
