|
| 1 | As Per RUIDP SOR 2023 (Part A) Civil Work) |
| 2 | Earth work in excavation in foundation, trenches etc. includingdressing of sides and ramming of bottoms, including getting out theexcavated material, refilling after laying pipe/ foundation anddisposal of surplus excavated material at a lead upto 50m suitablesite as per direction of Engineer for following depths, below natural ground / Road top level. |
| 3 | Providing and laying in position cement concrete of specified gradeexcluding the cost of centring and shuttering - All work upto plinth level :1:5:10 (1 cement : 5 fine/ coarse sand : 10 graded stone aggregate 40 mm nominal size) |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work upto plinth level :1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) |
| 5 | Cement concrete flooring 1:2:1 (1 Cement 2 coarse sand :4 graded 20mm nominal size stone aggregate) finished with a floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete. 40mm thick |
| 6 | Random Rubble stone masonry for with hard stone in foundation and plinth Cement Morlar 1:6 (1-Cement: 6 Coarsc-Sand). |
| 7 | Cement plastering including T & P, scaffolding, material and complete labour,including cost of water, curing, racking of joints cic. with 20mm cement plaster of mix.1:4 (1 Cement :4 fine/coarse sand). Extra for providing and making water proofing malerial in cement plaster work in proportion recommended by the manufactures. |
| 8 | Neat cement punning Same as above ilem plaster qly. |
| 9 | Providing gola 75 x 75 mm in cement concrete1: 2: 4 (1 cement: 2 coarse sand : 4 stone aggregate 10 mm and down gauge) including finishing with cement mortar 1: 3(1 centent: 3 fine sand) as per standard design in 75 x 75 mm deep chase. |
| 10 | Brick work with FPS bricks of classdesignation 75 in foundation and plinth in.Cement mortar 1:6 (1 Cement :6 Coarse Sand). |
| 11 | Centering and shuttering with plywood or steel sheet upto two stories or height up to 7.5 meter above plinth level including strutting - propping etc. and removal of form for:Foundation, Footings, bases of columns etc for mass concrete. |
| 12 | Providing and laying in position specified grade reinforced cement concrete inishing and reinforcement -All work upto plinth level: 1: 1 ½ : 3(1 cement : 2 coarse sand: 3 graded stone aggregate 20 mmnomina Lsize) |
| 13 | Brick work with FPS bricks of class designation 75 in superstructure above plinth level upto loo stories in all shapes and sizes in. Cement mortar 1:6 (1 Cement :6 coarse send) |
| 14 | Half brick masonry with FPS bricks of class designation 75 in superstructure above plinth level upto tvo staries. Cement mortar 1:4 (1 Cement :4 coarse sand). |
| 15 | centering and shuttering with plywood or steel sheet upto two stories or height upto 75 metre above plinth level including strutting. propping etc. and removal of form for. Suspended floors, roofs, landings, balconies and access platform. |
| 16 | Reinforced cement concrete work in beans,suspended flaors, roofs having slope upto 15° Landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair coses upto hvo stories excuding the cost of centering, shuttering, finishing and reinforcement. M-20 Grade concrete (1:1.5:3)(1 Cement: 1.5 coarse sand :3 graded stone aggregate 20mm nominal size). As per design mix. |
| 17 | Cement plaslering including T&P , scaffolding, material and complete labour, including cost of water, curing, racking of joints ele. with 20mm cement plaster of mix. 1:4 (1 Cement :4 fine/coarse sand). |
| 18 | Cement plastering including T&p scaffolding, material and complete labour, including cost of water, curing, racking of joints etc. with 12mm cement plaster of mix.1:3 (1 Cement :3 fine/coarse sand). |
| 19 | Cement plaslering including T& P,scaffolding, material and complete labour, including cost of waler, curing, racking of joints ele. with 20mm cement plaster of mix.1:4 (1 Cement :4 fine/coarse sand). Pointing on brick work or brick flooring with cement mortar 1:3 (1 Cement :3 fine sand). |
| 20 | Providing and fixing 1' quality standard white grey ivory fume red brown light green light blue and other light shades glazed tiles confirming to IS: 13753 & IS 15622 of size 200mm x300mm in wall foors, steps, pillars etc. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the tile complete (excluding the cost of cement plaster on walls and pillar). Extra for using size above 200x300mm in glazed tiles and for using 400mm x 400mm MAT finished tiles in place of 300mmn x300mm size. |
| 21 | Cement plastering including T&P, scaffolding, material and complete labour,including cost of water, curing, racking of joints ete. with 12mm cement plaster finished with a floating coat of neat cement of mix 1:4 (1 Cement :4 fine/coarse sand).Same as above item glazed tiles gly. |
| 22 | Providing and fixing Ist quality MAT finished ceremic Lile size300x300mm confirming to IS: 13755 and IS: 15622 colour such as white, grey, ivory, fume red brown, light green, light blue and other light shades in floors, steps, pillars ele. laid on a bed of neat cement slurry finished with flush pointing in the white cement mixed with pigment to match the shade of the lile complete (including the cost of cement morlar bed1:4).Extra for using size above 200x300mm in glazed tiles and for using 400mm x 400mm MAT finished tiles in place of 300mm x 300mm size. |
| 23 | Providing and fixing Granite stone slab mirror polished and machine edge cut in walls, pillars, steps, Shelves, Silis Counters Floors etc. laid on 12mm (Av.) thick base of cement mortar 1:3 (1 cement: 3 coarse sand) jointing with white cement mortar 1:2 (1white cement: 2 marble dust) with pigment lo match the shade of the marble slab including grinding, rubbing and polishing complete. Jalore(Red/Choclate Colour. Above 3601 Cm2 Slabs. |
| 24 | Extra for providing edge moulding to 15-18mm thick marble/ Granite stone counters, Vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-incharge.Granite Work. |
| 25 | Reinforcement for R.C.C. work at all level including straightening cutting, bending. placing in position and binding all complete.Cold twisted bars. |
| 26 | Providing and fixing aluminum work for doors windows ventilators and partitions sith extruded builk up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and 15: 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at lop, botlom and sides with required PVC / neoprene felt ele Aluminium sections shall be smooth rust free straight milered and joints mechanically wherever required including cleat angle, aluminum beading for glazing/ paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the direction of Engineer in charge (Glazing and paneling to be paid for separately) Powder coated aluminum (minimum thickness of powder coating 50 micron). |
| 27 | For shutters of doors, windows & ventilators including providing and fixing hinges/ pivols and making provision for fixing of filings wherever required including the cost of PVC / neoprene gasket required (Fittings shall be paid for separalely) powder coated aluminium (minimum thickness of powder coating 50 micron). |
| 28 | Providing and fixing double action hydraulic of approved brand and manufacture IS: 6315 marked, for doors including cost of culting floors as required, embedding in floors and cover plates with brass pivot and single piece M.S sheet outer! box with slide plates etc. complete as per the cover plate. direction of engineer in charge. With brass |
| 29 | Providing and fixing IS : 3564 marked Aluminium executed section body tubular type universal hydraulic door closer with necessary accessories and screws etc. complete. |
| 30 | onstruction masonry chamber 30x30x50cm. inside with 75 class designation brick work in cement mortar 1:4 (1 Cement :4 coarse sand)stop cock with C.l. surface box 100x100x75mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1Cement :2 coarse sand :4 graded slone aggregate 20mm excavation nominal size)necessary foundation concrete 1:5:10 (1 Cement :5 fine sand 10 graded stone aggregate 40mm nominal size) and inside plastering with cement mortar 1:3 (1 Cement :3 coarse sand) 12mm thick finished with a floating coat of neat cement complete as per standard design. With bricks. |
| 31 | Providing and fixing 12 mm thick prelaminated particle board flat placed three layer or graded wood particle board conforming to 15: 12823 Grade 1 Type IT, in paneling fixed in aluminum doors, windows shutters and partition franes with C.P. brass / stainless steel screws etc. Complete as per |
| 32 | Providing and fixing glazing in aluminium door, window‚ventilatorshutters and partitions ele. with PVS / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-incharge /Cost of aluminium snan hendino shnll |
| 33 | Providing and applying plaster of Paris putty of 2mm thickness over plastered surface to prepare the surface even and smooth complete |
| 34 | Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade including all scaffolding: Two or more coats on new work. |
| 35 | P& F Aluminium Composite Pannel (ACP) with complete work |
| 36 | Providing and placing on terrace (at all floor levels polyethylene water storage tank ISI: 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank |
| 37 | Providing and fixing toilet paper holder: C.P. brass |
| 38 | Carriage of Earth material up to 7.0 Km. |
| 39 | Providing and installation automatic sanitary napkin incineralor disposal machine. |
| 40 | Providing and installation of aerosol dispenser/ airfreshner |
| 41 | Providing and installation sanitary vending machine digital display automatic with multiple coins. |
| 42 | Providing and installation Sanitary bin stainless steel plain peddle win with cover. |
| 43 | Providing and installation handwash liquid dispeser hand wash size 6x9x22cm capacity 400ML plastic body. |
| 44 | Providing and installation of auto hand dryer made of A.B.S. body Including all necessary electric connection etc. |
| 45 | Provision for Retro Sign board & notice |
| 46 | Provision for 1 H.P. notor |
| 47 | Provision for Beautifying area |
| 48 | (Part B) Sanitary Work |
| 49 | Providing, lowering, laying in trenches, aligning. fixing in position and jointing uPVC pipe fittings/accessories of class II (6 Kg/Sqcm) conforming to 15:7834 suitable for potable water with rubber rings joints in uPVC pipe line at all level/depth including all material, labour hydraulic testing and commissioning as per technical specifications and as per direction of Engineer. Equal Tee (Moulded) welded with socket. |
| 50 | 110 mm dia |
| 51 | 160mm dia |
| 52 | Construction brick masonry manhole in cement mortar 1:4 (1 Cement :4 coarse sand) R.C.C. top slab with 1:2:4 mix (1 Cement :2 coarse sand :4 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 mix (1 Cement :4 coarse sand :8 graded stone aggregate 40mm nominal size). Inside plastering 12mm thick with cement mortar 1:3 (1 Cement :3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:24 (1 Cement :2 coarse sand :4 graded stone aggregate 20mm nominal size finished with a floating coat of neat cement complete as per standard design. Inside size 90x80cm and 45cm deep including C.1. Cover with frame (light duty) 455x610mm internal dimensions total weight of cover and frame to be not less than 38kg (weight of cover 23kg and weight of frame 15 kg.). with bricks with class designation 75.Inner Side |
| 53 | (Indian type w.c. pan) with 100mm sand cast iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (Handle lever) conforming to IS:7231, with all fittings and |
| 54 | Providing and fixing whiter vitreous china pedestal type water closet (European type) with seat and lid,1O litre low level white vitreous china lushing cistern & C.P. flush bend with fittings & C.J.brackers 40mm flush hend overflore arransement |
| 55 | Providing and fixing wash basin with C.l. brackets, 15mm C.P. brass pillar taps, 32mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required. White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap. |
| 56 | Providing and fixing wash basin with C.l. brackets, 15mm C.P. brass pillar taps, 32mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required. White Vitreous china Flat back wash basin size 450x350mm with a single15mm C.P. brass pillar taps. |
| 57 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931. 15 mm nominal bore |
| 58 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore. |
| 59 | Providing and fixing C.P. brass bib cock of approved quality conforming to 15:8931. 15 mmnominal bore. |
| 60 | Providing and fixing PTMT grating of approved quality and colour. Circular type.125 mm nominaldia with 25mm waste hole. |
| 61 | P & F Pillar cack Jaquar Make with complete work. |
| 62 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour. 450MM long towel rail with total length of 495mm, 78mm wide and effective height of 88mm, weighing not less than 170 gms |
| 63 | P& FPowder Coated Hanger with complete work. |
| 64 | Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements. Weighing not less than 106 gms. |
| 65 | Providing and fixing Jet Spray with complete work. |
| 66 | Providing and fixing gun metal non- return valve of approved quality (screwed end) :25 mm nominal bore. Horizontal |
| 67 | Supplying and fixing C.l. cover without frame for manholes: 455x610 mm rectangular C.l. cover (light duty) the weight of the cover to be not less than 23 kg. |
| 68 | Providing and fixing Chlorinated Polyviny! Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work including cutting chases and making good the walls etc., 25mm nominal outer dia Pipes. |
| 69 | Providing and Fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work including cutting chases and making good the walls etc., 20 mm nominal outer dia Pipes. |
| 70 | Providing and fixing 600 X 450mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete |
| 71 | Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc. Including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete i/e fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc. of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer in charge. (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) |
| 72 | Providing and fixing sticker lettering and figuring. |
| 73 | P & F Sanitary Win Stainless steel. |
| 74 | (Part C) Electric Work |
| 75 | Wiring of light point/ fan point/ exhaust fan point/ call bell point as per PWD specificalion for electrical Works with ISI marked 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade (IS:694) and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper earth conductor 1.1 kV grade (IS:694) in recessed ISI marked MMS (IS:9537 P - III) vergin material PVC conduit & it's all accessories J.B. Bends etc.), round tiles, 18 SWG Hot Dipped Galvanized Modular Box with earth terminal, 6 A Modular switch, Modular face plate with grid plate, 3 pin ceiling rose / lamp Holder/ 3 pin connector, screws etc, making connections, all as per pre approved by Engineer in charge. testing etc. complete as required. For specification of copper Conductor, Phenolic Laminated sheel's & Electrical/ Wiring accessories referChapter E - 04, E - 05 & E - 07. For additional technical parameters of products/ work, refer Annexure \\"A\\" attached with this BSR. |
| 76 | Long Point |
| 77 | Medium Paint |
| 78 | Short Point |
| 79 | Wiring of 3/5 pin 6 amp. Light plug point as per PWD specification for electrical Works with ISI marked 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible copper conductor 1.1 kV grade (IS:694) and 1.5 sq. mm nominal size FR PVC insulated unsheathed flexible capper earth conductor 1.1 kV grade (IS:694) in recessed ISI marked MMS (IS:9537 P - III) vergin material PVC conduit & il's all accessaries J.B. , Bends etc.), round tiles, 18 SWG Hot Dipped Galvanized Modular Box with earth terminal, 6 A modular switch, 3/ 5 pin 6 A modular sockel. Modular face plate with grid plate, screws etc,all as per pre approved by Engineer in charge, making connections, testing elc. complete as required. For specification of copper Conductor, Phenolic Laminated sheet's & Electrical/ Wiring accessories refer Chapter E - 04, E - 05 & E - 07. For additional technical parameters of products/ work. refer Annexure \\"A\\" atlached with this BSR |
| 80 | Medium point |
| 81 | Long point |
| 82 | Supplying and drawing FR PVC insulated & unsheathed exible copper conductor as per PWD specification for electrical Works with ISI marked (IS:694) and as per IS 8130: 2013 of 1.1 kV grade. Wire should be made from 99.99% purily copper, class 5 stranding in acc. to lEC 60228 for lower walt loss, oxygen free (<10 ppm) for less chances of oxidization and higher silver content for gives better conductivity, insulalion PVC type A or C.Mame retardant as per IS 10810-53, better amperage rating as per VDE 0298 part 4,. in existing surface or recessed PVC/ MS conduit/casing capping including all as per pre approved by Engineer in charge, makingconnections, etc. as required OEM Must have its own in house NABL lab selup for all tesling facilities for wires. For additional technical parameters of products/ work, refer Annexure \\"A\\"altached with this BSR. |
| 83 | Providing & Fixing of 240/415 V AC MCB with positive isolation of breaking capacity not less than 10 KA (B/ C tripping characteristic as per type of load and sile requirement) 4KV impulse withstand voltage, as per PWD specification for electrical Works with ISI marked IS 8828(1996) / conforming to EC 60898-1 2002, 1EC 60947-2, low watt losses, trip free mechanisum, energy limiting of class 3 as per IEC, minimum phase terminalion capacily of 35sq.mm., conductorline load reversibifity, label halding facility, IP 20 contact protection and filted with existing distribution board/sheets, min. operation 20,000 upto 32 A raling and 10,000 upto 63 A, 5000 for 80 A raling including making connections, testing etc. as required.. OEM shall have submit NABL / CPRI / ERDA accrediated lab lest reports before execution & All as per pre approved by Engineer in charge. For additional technical parameters of producis/ work, refer Annexure \\"A\\" attached with this BSR .6 A to 32 A raling |
| 84 | Providing & Fixing of 240/415 V isolator as per PWD specification for electrical Works with ISI marked IS:13947-Ill/conforming to IEC 60947-3, suitable for AC2ZA utilization calagory, 4KV Impulse withstand voilage, rue contact indication, Red colour dolly/ lever shall have single mould covering over all poles for operation, two position din rail mounling, minimum phase terminalion capacity of 35sg.mm. , label holding facility, IP 20 contact protection and fitted with existing distribution board / sheet including making conneclions, testing etc. as required. OEM shall have submit NABL / CPRI/ ERDA accrediated lab test reports before execution & All as per pre approved by Engineer in charge. For additional technical parameters af products/ work, refer Annexure \\"A\\" altached with this BSR. BSR. A / 40 A rating |
| 85 | Supply & drawing Wiring for sub mains as per PWD specificalion for electrical Works with ISI marked (IS:694) .1100 Volts grade PVC insulated fat twin core sheathed solid aluminium conductor with 10 SWG G.I. Support wire duly clipped including all as per pre approved by Engineer in charge, making connections, as required. OSM must have its own in house NABL lab for all testing facilities for wires for additional technical parameters of products/ wark, refer Annexure \\"A\\" attached with this BSR .4.0 sq.mm |
| 86 | Providing & Fixing of IK09 recessed/surface mounting heavy duty horizonlal type sheet steel not less then 1.2 mm thick Distribution board as per PWD specification for electrical Works ISI marked conforming to IS-13032 & IS-8623 / conforming to IEC 61439-3. Phosphatised/ powder painted complete with suitable rating insulated copper bus bar, shorting link, neutral link, earth link, connecting wire of suitable rating and din bar,masking sheet, including making intemal Dterminations with copper lugs and with detachable gland plate, including making connections, testing etc. as required.OEM shall have submit NABL / CPRI / ERDA accrediated lab test reports before execution & All as per pre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure \\"A\\" attached with this BSR. 4 Way (4 O/G +2 I/C) |
| 87 | Providing & Fixing of ISO Certified company made BEEStar rated copper wounded double ball bearing capacitor start, aluminium body & Metallic blade ceiling fan as per PWD specification for electrical Works, Conform to all the performance requirements laid down in IS:374-2019 including all amendments, as applicable: & Carry BIS licensing (i.e. ISI marking) or Quality Certification such as ISO - 9001 arabove. with down rod up to 30 cm with secondary support safety cable (steel wire), cotter pin vilh 3 x 1.5 sq.mm puc insulated flexible copper conductor making connection tesling etc. as required. Appropriate OEM test certificate shall be submitted by contractor. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure \\"A\\" attached with this BSR. 1200mm Sweep BEE 3 Star rated (service value >=5.0 (os 5.5 ) |
| 88 | Providing & Fixing of Heavy duly capacitor start, copper woind Double ball bearing 900/1400 RPM single phase E150900+ (1) Exhaust fan as per PWD specification for electrical Works, conforming lo IS:2312 ISI marked in existing opening including making connections testing etc. as required. OEM shall be an IS certified company. Appropriate OEM test certificate shall be submitted by contractor. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure \\"A\\" altached with this BSR. 300mm sweep(900/1400 RPM) |
| 89 | Providing & Fixing of IP 20 box made out from 1.2mm thickCRCA sheet steel with depth of minimun 30mm and finished with powder coating and suitable for mounting LED tube including side covers, holders. internal wiring to luminate the single sided connection LED tube. (Without tube). All as per pre approved by Engineer in charge. For additional technical parameters of products/ work ,refer Annexure \\"A\\" altached with this BSR.Suitable for 4' LED Tube shape fixture 2 X 18/20 W |
| 90 | Providing & Fixing of Fluorscent tube rod in existing fixtures as required complete in all respect. All as per pre approved by Engineer in charge. For additional technical parameters of products/ work, refer Annexure \\"A\\" allached with thisBSR |
| 91 | Providing & Fixing of IP40 LED Recessed / Surface Mounted, Round / Sqaure Non-Dimmable Back lit SMD Mid Power LED Downlight with die-cast aluminum housing & Heat Sink for heat dissipalion with UV Stabilized non yellowish Diffuser with internal/ external BIS complience 2.5 KV surge protected Isolated driver, with Short & Open circuit protection, having efficiency 85% and in compliance to IEC standards. System Lumen efficacy of ≥ 120 Im / watt, THD < 10%,p.f.20,95, CRi>80, life time of minimum 50000 Burning Hours with, 70% of intial Lumen maintaned till life ends, CCT 3000°K / 4000°K / 5700°K /6000 K/6500°K (As per ANSI Bin) , maximum power consumption should not more than the specified rating and Fixture shall be of BIS standard and trade marki certificate (T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen prinling on housing. OEM must have is own in house NABL lab setup for all testing facilities for LED fixtures. (LM79/LM8O) certificate / Report fram OEM shall be submitted. All as per pre approved by engineer in charge. foe additional technical parameters of produci work, refer Annexure \\"A\\" attacheded with this BSR. Recessed Mounting. LED Downlight 18/20W |
| 92 | Providing and fixing Cable With Complet work. |
| 93 | (Part D)Sewer works |
| 94 | Earth work far Sewer line and Manhole In exeavation in Loundatios, trenches manholes, road side chambers etc Including dressing of sides and ramming of bottoms, Including zetting out the encavated materla, refiling after laying pipe/ fausdatton and disposat ef surplus excarated materlalata lead upto 50m sultable site as per direttian of Engineer for follawing depths, below natural ground / Road top level including allowances for any additional excavation beyand the drawings (measurement for payment to be as per standard drawings, re-handling of materlaVearth to complete the task |
| 95 | In all types scils/ saturated soil such as moorum, sand, sandy silt, clay. black cotton soil, kankar, etc. |
| 96 | Dismarting of feuble panements for sewer line and manhales andduposal of dumanuled matthals ap to a lead of 50 metres as directed by Enguner intluding altenances for any additional dumaraling beyond the drawing (mesurement for payment to be as per sendard drawingal, re-banding of malenal'eath to complete the task |
| 97 | Bituminous courses |
| 98 | Grarulat cones |
| 99 | Providing as ate, loenng & laying in trenches, aligaung & jonnang eSRCC ppea :173 class (wath as cras) 1S 458 - 1959 (amended up lo dale) muled and pipes from 300 man upto 2000 tom mandactured trouzh setical / nbrated cartng process all levtls นายh สินbbe gaict (EPDS1SBR) for vewer tnes ม per IS 5382 (rnetuduag cost of Rabber gaskets labncants) as per drausng. cueral hydro tessng of the sewer pipe lise (uncludung cost and comeyace aluater to site for testnal ets, complete as dareeted by Engrocer Note Et to be retsured and pard separately Length of pupe shall be encasured nbelueen the ater wall of tho manholes! Inspection chambers Pipe in the manhole/spection chamber's wall shall deemed to be meladed in the sem of manhole/uu pertion chumber thall sat be payble |
| 100 | 200 mm ocral Jumctes |
| 101 | Construction bnck maseery marhole in cement monม 14(1Eement & cuatte sand ) R CC top alab wrth 1 2 4 mat (I cemena acoune send → cement tone aggegete 20 rum poin sze)cundation concrete 148 ma (1 cement + coane und 3 gradedstone 8zgregale «1Omats netanal size) tude plastenng I2mtn thicksid cecent morar 1 1fl come: 3 coarse sanil) Grushed with fozung cat of neat cement and melang channels in cement concrete 124(1 ceman 2 core sand + graded come asgrgare 20mm communal astz) finned with a floating coat of ceat cement complete as por standard design |
| 102 | Inande sue 50280 cm sad 45 cm deep eluding Cl cover usthGrame Cight duty) 453e510 ma internal dimensiona total weight of cover and frame to be net less than 38 kg weight of cover 23 1g and amanht of frame 15 kg |
| 103 | Pranding granular balding harng width - cuter d of pipe (Bc) + 500mm, thickness below pipe • 025Be or 100mm (whichest 1s bigher) and haunching • O 5Be, with graded hard crusher broken one of 100% pazing through 20mm sheve, 30 to 50% passing mm n 00% reta on 3m shane, laying on Layers of thuckness 10/15cm including ramaning, consolidation ec complete foe all type of piper of fellowing sues as por drawing and or 2s darected by Engineer |
| 104 | 200 mum interal diameter |
| 105 | Carriage by mechanical transport including loading, unloading and azskang unto 5 0 Km earth |
| 106 | Stone, boulders, gravelly matema!(Excavaled duting road dumestalling |
| 107 | Pronding and laying in poshan cement concrete 1 3 6 (1 Comet 1|cum pralej come agarogate 20 mum naminal suze) in hase counse complete includiag all tatenal, labour, machinery, lighting. guarding for road resteraton uler suer line and manhole wark unclaling allowances for any additoral read restoratron beg oral the drawing i meaturement fur paytent to be as per standard drawings) intersee theat |
| 108 | Providing and Laying in poutien cement concrete of aperilled grade over prepared base coure complete incadung frahie cuning all matenal, labout, machunery, Lightung, guarding for toad restoration under inver ine and manhole work including allowan, ca fos any ddtand road restoraten beyood the drawerp measuscrrent for payment ba be au per vandard drawings) to complete the task M20 (1:1.5:3) Please Enable Macros to View BoQ information |
