|
| 1 | Clearing grass and removal of rubbish up to a distance of 50 metres outside the periphery of the area. item no. 2.02 |
| 2 | Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous surface cleaned with mechanical broom.item no. 5.02 i |
| 3 | Providing and laying dense bituminous macadam with higher capacity batch type hot mix plant using crushed aggregates of specified grading, premixed with bituminous binder @ 4.5 % by weight of total mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MoRTH specification clause No. 505 complete in all respects) with Modified Graded Bitumen.for Bituminous concrete grading -II with VG-30 Grade Bulk Bitumenitem no. 5.04A B |
| 4 | Providing and laying bituminous concrete with higher capacity batch type hot mix plant using crushed aggregates of specified grading, premixed with bituminous binder @ 5.4 % of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MoRTH specification clause No. 507 complete in all respects) with Modified Graded Bitumen.for Bituminous concrete grading -II with VG-30 Grade Bulk Bitumenitem no. 5.05A B |
| 5 | Road Marking with Hot Applied Thermoplastic Compound with Reflectorising Glass Beads on Bituminous Surface (Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes.)item no. 8.13 |
| 6 | Direction and Place Identification Signs upto 0.9 sqm Size Board. (Providing and erecting direction and place identification retro-reflectorised sign as per IRC:67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick or Aluminium composite material sheet with overall thickness of 4 mm with area not exceeding 0.9 sqm fixed over back support frame of min 35 x 35 x 3 mm Angle mounted on a mild steel circular pipe 65 NB, firmly fixed to the ground by means of properly designed foundation with M25 grade cement concrete 45 x 45 x 60 cm, 60 cm below ground level as per approved drawingitem no. 8.05 |
| 7 | Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC :67 made of class- B Type IV retro reflective sheeting fixed cover 2mm thick aluminium sheeting vide clause 801. 3, 3mm/4mm thick aiuminium composite material sheet depending on the size of the sign fixed over back support frame of min 25 x 25 x 3 mm Angle mounted on a mild steel circular pipe 65 NB, 3.2 mm thickness firmly fixed to the ground by means of properly designed foundation with M25 grade cement concrete 45 cm x 45 cm x 45 cm, 60cm below ground level as per approved drawing. The sign shall be maintained as per section 12 of IRC 67.90 cm equilateral triangleitem no. 8.04 (ii) |
| 8 | Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC :67 made of class- B Type IV retro reflective sheeting fixed cover 2mm thick aluminium sheeting vide clause 801. 3, 3mm/4mm thick aiuminium composite material sheet depending on the size of the sign fixed over back support frame of min 25 x 25 x 3 mm Angle mounted on a mild steel circular pipe 65 NB, 3.2 mm thickness firmly fixed to the ground by means of properly designed foundation with M25 grade cement concrete 45 cm x 45 cm x 45 cm, 60cm below ground level as per approved drawing. The sign shall be maintained as per section 12 of IRC 67.60cm circularitem no. 8.04 (viii) |
| 9 | Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC :67 made of class- B Type IV retro reflective sheeting fixed cover 2mm thick aluminium sheeting vide clause 801. 3, 3mm/4mm thick aiuminium composite material sheet depending on the size of the sign fixed over back support frame of min 25 x 25 x 3 mm Angle mounted on a mild steel circular pipe 65 NB, 3.2 mm thickness firmly fixed to the ground by means of properly designed foundation with M25 grade cement concrete 45 cm x 45 cm x 45 cm, 60cm below ground level as per approved drawing. The sign shall be maintained as per section 12 of IRC 67.80cmx60cm rectangularitem no. 8.04 (x) |
| 10 | Providing and fixing of retro- reflectorised cautionary, mandatory and informatory sign as per IRC :67 made of class- B Type IV retro reflective sheeting fixed cover 2mm thick aluminium sheeting vide clause 801. 3, 3mm/4mm thick aiuminium composite material sheet depending on the size of the sign fixed over back support frame of min 25 x 25 x 3 mm Angle mounted on a mild steel circular pipe 65 NB, 3.2 mm thickness firmly fixed to the ground by means of properly designed foundation with M25 grade cement concrete 45 cm x 45 cm x 45 cm, 60cm below ground level as per approved drawing. The sign shall be maintained as per section 12 of IRC 67.60cmx45cm rectangular |
| 11 | Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts & leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of table No. 300-2 Rolling with vibratory rolleritem no. 3.18 |
| 12 | Solar Powered Road Marker (Solar Stud) Supplying of Solar Raised Pavement Markers made of polycarbonate molded body with circular shape, solar powered, LED self illumination in active mode 360 degree illumination and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face in passive mode.The marker shall support a load of 20000 kg tested in accordance to ASTM D 4280.The marker should be resistant to dust and water ingress according to IP 65 standards and should withstand temperatures in the range of 0 C to 70 C. Color of lighting could be provided in red or yellow (amber) as per requirement and typical frequency of blinkikng in 1 Hz.There should be current losses of less than 20 microamperes at 2.4 V in sleepcharging mode to enhace the life of the marker and a full charge should provide for a minimum autonomy of 50 hours.The height, width and length of the marker shall not be less than 10mmx100mmx100 mm. Also, the surface diameter of the marker shall not be less than 100 mm respectively.The weight of the marker shall not exceed 0.5 Kilograms.Fixing will be by drilling holes on the road for the shanks to go inside, without nails and using epoxy resin based adhesive and complete as directed by the engineer.)item no. 8.35 |
| 13 | Kilometre Stone (Reinforced cement concrete M15 grade kilometre stone of standard design as per IRC:8-1980, fixing in position including painting and printing etc) (ii) Ordinary kilometer stone (precast)item no. 8.14 (ii) |
| 14 | Road Delineators (Supplying and installation of delineators (road way indicators, hazard markers, object markers), 80-100 cm high above ground level, painted black and white in 15 cm wide stripes, fitted with 80 x 100 mm rectangular or 75 mm dia circular reflectorised panels at the top, buried or pressed into the ground and confirming toIRC-79 and the drawings.)item no. 8.15 |
| 15 | Type - A, \\"W\\" : Metal Beam Crash Barrier Providing and erecting a \\"W\\" metal beam crash barrier comprising of 3 mm thick corrugated sheet metal beam rail, 70 cm above road/ground level, fixed on ISMC series channel vertical post, 150 x 75 x 5 mm spaced 2 m centre to centre, 1.8 m high, 1.1 m below ground/road level, all steel parts and fitments to be galvanised by hot dip process, all fittings to conform to IS:1367 and IS:1364, metal beam rail to be fixed on the vertical post with a spacer of channel section 150 x 75 x 5 mm, 330 mm long complete as per clause 811item no. 8.23 A |
| 16 | Painting two coats after filling the surface with synthetic enamel paint in all shades on new plastered concrete surfacesitem no. 8.08 |
| 17 | Excavation for Structures (Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material.S.O.R. Item No. 12.01 B(i) |
| 18 | PCC 1:3:6 in Foundation (Plain cement concrete 1:3:6 nominal mix in foundation with crushed stone aggregate 40 mm nominal size mechanically mixed, placed in foundation and compacted by vibration including curing for 14 days.)S.O.R. Item No.12.04 |
| 19 | Plain/Reinforced cement concrete in sub-structure complete as per drawing and technical specifications RCC Grade M20 using batching plant, transit mixer & concrete pump Hight upto 5mS.O.R. Item No. 13.05 E (p) |
| 20 | Furnishing and Placing Reinforced/Prestressed cement concrete in super-structure as per drawing and Technical Specification RCC Grade M25 using batching plant, transite mixer & concrete pump Hight upto 5mS.O.R. Item No. 14.01 B (p) |
| 21 | Supplying, fitting and placing HYSD bar reinforcement in sub-structure complete as per drawing and technical specifications S.O.R. Item No. 13.06 |
| 22 | Add 18% GST : |
| 23 | Add 1% Labour Cess: Please Enable Macros to View BoQ information |
