|
| 1 | MRL03-NAMONI BALIJAN PMGSY ROAD TO DEUGHORIA VIA PUWAL GHAT |
| 2 | Clearing and grubbing road land including uprooting wild vegetation, grass, bushes, shrubs, saplings and trees of girth upto 300 mm, removal of stumps of such trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, upto a lead of 1000 m including removal and disposal of top organic soil not exceeding 150 mm in thickness as per Technical Specification Clause 201.[SOR 25-26] [Item No. 2.2(i-a)] i. By Manual Means (A) In area of non thorny jungle |
| 3 | Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 1000 m as per Technical Specification Clause 301.5 [SOR 25-26] [item No.3.4 (i)] |
| 4 | Construction of Sub-grade and earthen shoulder with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 with lead up to 1000m as per Technical Specification Clause 303.1 [SOR 25-26] [item No.3.14 (i)] |
| 5 | Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401.[SOR 25-26] [item No.4.1 (A-i)]For Grading I Material |
| 6 | Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening/binding materials to fill-up the interstices of coarse aggregate, watering and compacting to the required density grading 2 as per Technical Specification Clause 405.Using stone screening Type-B 11.2 mm for Gr.II [SOR 25-26] [item No.4.7 (II-A)]By Manual Means |
| 7 | Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with smooth wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming, stone screening to fill-up the interstices of coarse aggregate, watering and compacting to the required density Grading 3 as per Technical Specification Clause 405 Using stone screening Type-B 11.2 mm for Gr.III [SOR 25-26] [item No.4.7 (III-A)]By Manual Means |
| 8 | Prime Coati. Low porosityProviding and laying Primer coat with Bitumen(SS-1) on prepared surface of granular base including clearing of road surface and spraying primer at the rate of 0.70-1.0 kg/Sqm using mechanical means as per technical Specification Clause-502. [SOR 25-26] [Item No. 5.1 (i)] |
| 9 | Tack CoatProviding and applying tack coat with Bitumen emulsion (RS-1) using emulsion Distributor at the 0.20-0.25 kg per sqm on the prepared Bituminous/Granular Surface cleaned with hydraulic broom as per Technical Specification -503 [SOR 25-26][Item No. 5.2 (i)] |
| 10 | 20mm thick close-Graded Mix Seal Surfacing using Bituminous Binder mixing with processed waste plastice (as per IRC-SP,98-20130 by replacement of 8% Bitumen binder by weight: Providing, laying and rolling of close-graded mix seal surfacing material of 20 mm thickness composed of 11.2 mm to 0.9 mm (Type-A) or 13.2 mm to 0.9 mm (Type-B) aggregates using with bituminous binder (@18.25 ka per 10sqm (ic 92% of standard Bitumen and 8% waste proccessed plastice by weight shall be used for coating aggregate after its heating) as per IRC:SP: 98 2013, laying to required ine, grade and level to serve as wearing in a suitable plant, laying and rolling with a three wheel 80-100KN static roller capacity, finished to required level and grades as per technical specification clause 509 to be followed by seal coat of either Type-A,Type-B or Type-C as per technical specification. |
| 11 | Road Safety & FurnitureReinforced cement concrete M15 grade Kilometre stone /local stone of standard design as per IRC:8 fixing in position including painting and printing etc. as per drawing and Technical specification Clause 1703 Ordinary K.M. stone (precast)[SOR 25-26][Item No. 10.10 (ii)] |
| 12 | Reinforced cement concrete M15 grade Hectometre stone /local stone of standard design as per IRC:8 fixing in position including painting and printing etc. as per drawing &Technical specification Clause 1703 (iii) 200 mt stone (precast) [SOR 25-26][Item No. 10.10 (iii)] |
| 13 | Providing and fixing of Reference Bench Mark / Temporary Bench Mark [RA-12] |
| 14 | Providing and erecting direction and place identification retro-\reflectorised sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3, fixed over aluminium sheeting, 2 mm thick with area exceeding 0.9 sqm supported on mild steel angle iron posts 75 mm x 75 mm x 6 mm, 2 Nos. firmly fixed to the ground by means of properly designed foundation with M-15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per approved drawing and Technical Specification Clause 1701.[SOR 25-26][Item No. 10.4 (A1)] |
| 15 | Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and Technical Specification Clause 801. Warning Signs [600mm -Triangle] [SOR-25-26][Item No. 10.2.A1-ii] |
| 16 | Providing and fixing of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5 mm thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450 mm x 600 mm, 600 mm below ground level as per drawings and Technical Specification Clause 801. Stop Sign [600mm -Cricular] [SOR-25-26][Item No. 10.2.A1-iii] |
| 17 | Reinforced cement concrete M15 grade boundary pillars/local stone of standard design as per IRC:25, fixed in position including finishing and lettering but excluding painting as per drawing and Technical Specification Clause 1704 [SOR-25-26][Item 10.11] |
| 18 | Providing and fixing of typical PMGSY informatory sign board with Logo as perMORD specifications and drawing. Three MS Plates of 1.6 mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will bepainted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1 [SOR-25-26] [Item No.10.16] |
| 19 | Providing & fixing Logo Board of PRADHAN MANTRI GRAM SADAK YOGNA as per standard design of National Rural Infrastructure development agency, diamond size (600 X 600 mm) 3 mm thick ACM plate and board plate size (1100 X 300 mm) 3 mm thick ACM plate and 2.4 m deep length square hollow section (75 X 75 X 6 mm) size including fitting and painting lettering with retroreflective sheeting class B as per drawing incl. fixing in CC M20 (450 X 450 X 600 mm) as per IRC 67 [RA-7] |
| 20 | Providing & fixing of typical PMGSY Citizen's information board consisting of two Aluminium Composite Material (ACM), 4mm thick face to be fully covered with high intensity prismetic sheeting type-4 class A/B material specification as per clause 1701.3.7. ACM sheets shall be of size 900mmX750mm each welded over welded MS flat iron frame of 50mm x 6mm size on back on edges. The flat iron frame of the bottom plate will be welded to 1 no. 75mm x 75mm x 6mm Square tube post. The steel tube post will be embedded in cement concrete M15 grade of 600mm x 600mm x 750mm below ground level. The height of lowermost part of the bottom plate will be 650 mm from normal ground level. The lettering and border etc. of ACM sheets on top & bottom shall be as per clause 1701.4.6 messages/borders. All the sections of frame and posts will be painted with primer and two coats of epoxy paint. The steel tube below ground level will be painted with three coats of epoxy paints. The design, painting and lettering shall be done as per approved drawing [RA-8] |
| 21 | Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflecProviding and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes and conforming to the MoSrt&H specificationstorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35. The finished surface to be level, uniform and free from streaks and holes. [SOR-25-26][Item No. 16.34] |
| 22 | Cross Drainage WorksExcavation for Structures (Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material. I Ordinary soil,A Manual Means,(I) Without dewatering,(i)upto 3 m depth [SOR-25-26][Item No. 11.1 (I)] |
| 23 | Sand Filling in Foundation Trenches as per Drawing & Technical Specification [SOR-25-26][Item No. 11.2 (i)] |
| 24 | Plain/Reinforced cement concrete, in open foundation complete as per drawing and technical specification including steel shuttering formwork.(N) Without plasticiser, A PCC Grade M-15 [SOR-25-26][Item No. 11.4 (I-B)] i) Nominal mix (1:2.5:5) |
| 25 | Plain/Reinforced cement concrete, in open foundation complete as per drawing and technical specification including steel shuttering formwork.(N) Without plasticiser, A PCC Grade M-20 [SOR-25-26][Item No. 11.4 (I-C)] i) Nominal mix Nominal mix (1:2:4) |
| 26 | Plain/Reinforced cement concrete, in open foundation complete as per drawing and technical specification including steel shuttering formwork.(N) Without plasticiser, C RCC Grade M-20 [SOR-25-26][Item No. 11.4 (I-D)] |
| 27 | Supplying, fitting and placing TMT bar reinforcement in open foundation complete as per drawing and technical specifications clause 1000 and 1202 [SOR-25-26][Item No. 11.7] |
| 28 | Plain/Reinforced cement concrete, in sub-structure complete as per drawing and technical specification including steel shuttering formwork.(N) Without plasticiser, A PCC Grade M-15 [SOR-25-26][Item No. 12.5 (I-A)] i) Nominal mix (1:2.5:5) |
| 29 | Supplying, fitting and placing TMT bar reinforcement in sub-structure complete as per drawing and technical specifications clauses 1002,1005,1010 &1202. [SOR-25-26][Item No. 12.6] |
| 30 | Plain/Reinforced cement concrete, in sub structure complete as per drawing and technical specification and steel shuttering formwork (N) Without plasticiser, E RCC Grade M-20, a) Height upto 5 m,Case-I [SOR-25-26][Item No. 12.5 (I-C)] i) Nominal mix (1:2.5:5) |
| 31 | Providing and laying Cement concrete wearing coat M-30 grade including reinforcement complete as per drawing and Technical Specifications Cl. 800 and 1206.3,With crushed stone [SOR-25-26][Item No. 13.5 (I)] |
| 32 | Providing Pressure relief pipes 100 mm dia. In bottom slab of box cell on a filter media base of 500x 500 mm as per drawing and technical specfication clause 1205.5.7 [SOR-25-26][Item No. 12.14] |
| 33 | Flexible Apron :Construction of flexible apron 1 m thick comprising of loose stone boulders weighing not less than 25 kg beyond curtain wall. [SOR-25-26][Item No. 14.10] |
| 34 | Construction of RCC railing of M25 Grade in-situ with 20 mm nominal size aggregate, true to line and grade, tolurence of vertical RCC post not to exceed 1 in 500, centre to centre spacing between vertical post not to exceed 2000 mm, leaving adequat space between vertical posts for expansion, complete as per approved drawings and technical specifications. [SOR-25-26][Item No. 13.6] |
| 35 | Back filling behind abutment, wing wall and return wall complete as per drawing and Technical specification , 'II -Sandy material [SOR-25-26][Item No. 12.10 (ii)] |
| 36 | Providing weep holes in brick/stone masonry abutment and return wall complete [SOR-25-26][Item No. 12.9] |
| 37 | Protection WorkExcavation for Structures (Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, construction of shoring and bracing, removal of stumps and other deleterious matter, dressing of sides and bottom and backfilling with approved material. I Ordinary soil,A Manual Means,(I) Without dewatering,(i)upto 3 m depth [SOR-25-26][Item No. 11.1 (I)] |
| 38 | Fillling in foundation trenches as per drawing and technical specification Clause305.3.9 [SOR-25-26][Item No. 11.2 (i)] Sand filling |
| 39 | Providing and laying boulder apron for bed protection with stone boulders of minimum size and weight as per Table 1300.1, no fragment weighing less than 25 kg laid dry complete as per drawing and technical specifications Clause 1301[SOR-25-26][Item No. 14.1] |
| 40 | Supplying, filling and laying in loose with Geo-textile bags of Type-A (1.03m x 0.70m) made of Geo textile non woven fabric sheets of 400 GSM manufactured from polyster/ polypropylene conforming to relevant ISO standard filled with specified sand/ silt from flood plain or adjacent char within a distance of 90 m of the work site including excavation, filling Geo bags with sand weighing 126.00 kg after filling, stitching the mouth of the filled bags with polypropylene or polyster complete as per technical specifications and as directed.[SOR-25-26][Item No. 16.51 (a)] With Boat1 bag = 0.721 sqm (1.03m * 0.70 m). 1sqm = 1.39 bag.(1 bag = 337 Rs. so 1.39 bag = 468.43 Rs.) Please Enable Macros to View BoQ information |
