|
| 1 | FURNITURE |
| 2 | OD227761/2025-2026: Manufacturing and supplying Reception Table of size 2000 (W) X 760 (D) x 1060 (H) with computer facility with following specification.The table top and gable end are made of 25mm thick chemicaly treated rubber wood of approved quality. The modesty panel is made of 18mm thick chemicaly treated rubber wood.The suface of the panel should be smoothly finish by polishing two coats of polyuretahane selaler and one coat of poly urethane top layer. Three drawers unit of size 400(W) x 150(D) x 450 (H) has been considered. One key board tray with sliding facility is considered . All side panels, shelves and drawer facia are made of 18mm thick chemicaly treated rubber wood . The drawer will have a multipurpose lock of approved make with premium quality.The rate shall be inclusive of cost of material, transportation, loading - unloading charges etc complete, as per manufatctures specification and directions of Engineer-In-charge st all levels. (refer the image in drawing no DP 1006 DRG CL 14 114) |
| 3 | OD228158/2025-2026:Manufacturing and supplying Junior Executive Table of size1220(W)X760(D)x760(H) with following specification.The tabletop and gableend are made of 18mmthick chemicaly treated rubber wood of approved quality. The side/stoarage panel is made of 15mm thick chemicaly treated rubberwood.The suface of the panel should be smoothly finish by polishing two coats of polyuretahane sealer and one coat of polyurethane top layer.One storage unit of size 400(W)x450(D)x715(H) has been considered.Four drawers unit of size 400(W)x150(D)x450(H) has been considered.All side panels,shelves and drawer facia are made of 24mm thick chemicaly treated rubberwood.The drawer will have a multipurpose lock of approved make with premium quality.The rate shall be inclusive of cost of material, transportation, loading-unloading charges,labour charges,all accessories like knob,lock, drawslider,nail bush25mmdia etc and complete,as per manufatctures specification and directions of Engineer-In-charge at all levels. (refer the image in drawing no DP 1006 DRG CL 14 114) |
| 4 | OD228153/2025-2026:Manufacturing and supplying teapoy with rack of size 900 (W) X 500 (D) x 480 (H) with with following specification.The main frame shall be made of size 30x30mm leg and panel with 30x15mm made of chemicaly treated rubber wood of approved quality and 8mm thick tinted or clear glass of approved make . The suface of the panel should be smoothly finish by polishing two coats of polyuretahane selaler and one coat of poly urethane top layer.The rate shall be inclusive of cost of material, transportation, loading - unloading charges and complete, as per manufatctures specification and directions of Engineer-In-charge at all levels. (refer the image in drawing no DP 1006 DRG CL 14 114) |
| 5 | OD228166/2025-2026:Manufacturing and supplying OPAC stand unit of size 1500 (W) X 1000 (D) x 760 (H) with following specification.The table top and gable end are made of 18mm thick chemicaly treated rubber wood of approved quality. The suface of the panel should be smoothly finish by polishing two coats of polyuretahane selaler and one coat of poly urethane top layer. One key board tray with sliding facility is considered .All side panels, shelves and are made of 18mm thick chemicaly treated rubber wood.The rate shall be inclusive of cost of all material, transportation, loading - unloading charges,labour charges and accessories like slider ,nail bush of dia 25mm etc complete, as per manufatctures specification and directions of Engineer-In-charge at all levels. (refer the image in drawing no DP 1006 DRG CL 14 114) |
| 6 | OD228157/2025-2026:Manufacturing and supplying book dispaly rack of size of size 1900 (W) X 1450 (D) x 400 (H)with following specification.The table top ,side panels,shelves are made of 18mm thick chemicaly treated rubber wood of approved quality. The suface of the panel should be smoothly finish by polishing two coats of polyuretahane sealer and one coat of poly urethane top layer. The rate shall be inclusive of cost of all material, transportation, loading - unloading charges,labour charges etc complete, as per manufatctures specification and directions of Engineer-In-charge at all levels. (refer the image in drawing no DP 1006 DRG CL 14 114) |
| 7 | OD228165/2025-2026:Manufacturing and supplying study carrels of size 3000 (W) X 460 (D) x 750 (H)with following specification.The table top ,side/end panels are made of 18mm thick chemicaly treated rubber wood of approved quality. The suface of the panel should be smoothly finish by polishing two coats of polyuretahane sealer and one coat of poly urethane top layer. The rate shall be inclusive of cost of all material, transportation, loading - unloading charges,labour charges etc complete, as per manufatctures specification and directions of Engineer-In-charge at all levels. (refer the image in drawing no DP 1006 DRG CL 14 114) |
| 8 | OD228164/2025-2026:Manufacturing and supplying book trolly of size of size 11700 (W) X 1000 (D) x 600 (H)with following specification.The trolly is made of 18mm thick chemicaly treated rubber wood of approved quality with dual PU castor wheel of 60mm dia. The suface of the panel should be smoothly finish by polishing two coats of polyuretahane sealer and one coat of poly urethane top layer. The rate shall be inclusive of cost of all material, transportation, loading - unloading charges,labour charges etc complete, as per manufatctures specification and directions of Engineer-In-charge at all levels. (refer the image in drawing no DP 1006 DRG CL 14 114) |
| 9 | OD228145/2025-2026:Manufacturing a supplying property rack of size 4550x 1900x750mm (40 counter) with following specification.The storage side panels ,shelves ,top and bottom panels are made up of 15mm thick chemicaly treated rubber wood of approved quality.The suface of the panel should be smoothly finish by polishing two coats of polyuretahane sealer and one coat of poly urethane top layer.The rate shall be inclusive of cost of all material ,abour charges, transportation, loading - unloading charges and accessories like nail bush 25mm dia etc complete, as per manufatctures specification,drawings and directions of Engineer-In-charge st all levels. (refer the image in drawing no DP 1006 DRG CL 14 114) |
| 10 | OD228163/2025-2026: Manufacturing and supplying Alamara with glass door of size 1900x1000x450mm with following specification.The storage side panels ,shelves ,top and bottom panels are made up of 15mm thick chemicaly treated rubber wood of approved quality.The door shutter are made of 24/15mm thick ( frame 24mm thick and panel slat 15mmthick) chemicaly treated rubber wood with 5mm float glas . The suface of the panel should be smoothly finish by polishing two coats of polyuretahane sealer and one coat of polyurethane top layer.The handles are Satin SS finish of 160mm pitch. All hinges considered are premium make. Necessary good quality hardwares have been considered as required. The alamara will have a multipurpose lock of approved make with premium quality.The rate shall be inclusive of cost of all material ,accessories ,labour charges, transportation, loading - unloading charges and accessories like handle,nail bush 25mm dia etc complete, as per manufatctures specification,drawings and directions of Engineer-In-charge st all levels. (refer the image in drawing no DP 1006 DRG CL 14 114) |
| 11 | OD228161/2025-2026:Manufacturing and supplying double side rack of size 1980x 1800x600mm with following specification.The storage side/centre panels are made of 24mm and shelves ,top and bottom panels are made up of 15mm thick panel chemicaly treated rubber wood of approved quality.The suface of the panel should be smoothly finish by polishing two coats of polyuretahane sealer and one coat of poly urethane top layer.The rate shall be inclusive of cost of all material ,abour charges, transportation, loading - unloading charges and accessories like nail bush 25mm dia etc complete, as per manufatctures specification,drawings and directions of Engineer-In-charge st all levels. (refer the image in drawing no DP 1006 DRG CL 14 114) |
| 12 | OD228154/2025-2026:Manufacturing and supplying teakwood stool of size 450 × 450 × 450 mm, made from approved quality teakwood. The legs shall be of size 50 mm × 50 mm, and the tabletop and gable ends shall be made of 15 mm thick teakwood.The foot rest shall be of 50x15mm thick teak wood. The surface shall be finished with approved polish like polyurathane, ensuring a smooth, even, and uniform finish.The rate shall be inclusive of the cost of all materials, manufacturing, polishing, transportation, loading and unloading, labour charges, higher charges for tools complete as per manufacturer?s specifications and directions of the Engineer-in-Charge at all levels. (refer the image in drawing no DP 1006 DRG CL 14 114) |
| 13 | OD228159/2025-2026: Manufacturing and supplying Alamara (5 compartment) of size 1800x900x400mm with following specification.The storage side panels ,shelves ,top and bottom panels are made up of 15mm thick,backing shall be 12mm thick teak wood of approved quality.The door /shutter frame shall be made of 70x25mm shutter panelling with 16mm thick teak wood panel. The surface shall be finished with approved polish with polyurethane, ensuring a smooth, even, and uniform finish.The handles are Satin SS finish of 160mm pitch. All hinges considered are premium make. Necessary good quality hardwares have been considered as required. The alamara will have a multipurpose lock of approved make with premium quality.The rate shall be inclusive of cost of all material ,accessories ,labour charges, transportation, loading - unloading charges and accessories like handle,nail bush 25mm dia etc complete, as per manufatctures specification, drawings and directions of Engineer-In-charge st all levels. (refer the image in drawing no DP 1006 DRG CL 14 114) |
| 14 | OD228156/2025-2026:Manufacturing and supplying Teak wood junior office Table of size1200(W)X750(D)x750(H) with following specification.The tabletop are made of 15mmthick and backing shall be 12mm thick teakwood of approved quality. The side/storage panel is made of 18mm thick and draw bottom shall be 16mm thick .The straight leg of size 50x50 and foot rest of size 50x20 shall be teak wood of approved . The suface of the panel should be finished with approved polish like polyurathane,ensuring smooth even and uniform finish. .One storage unit of size 400(W)x450(D)x715(H) has been considered.One drawers unit of size 400(W)x150(D)x450(H) has been considered. One key board tray with sliding facility is considered. The drawer will have a multipurpose lock of approved make with premium quality.The rate shall be inclusive of cost of material, transportation, loading-unloading charges,labour charges,all accessories like knob,lock, drawslider,nail bush25mmdia etc andcomplete,as per manufatctures specification and directions of Engineer-In-charge at all levels. (refer the image in drawing no DP 1006 DRG CL 14 114) |
| 15 | OD228160/2025-2026:Providing & fixing notice board of size 1200 x 900x100 to be made up of teak wood panel (side/back) of size 18mm thick .Door and shutter frame of size 60x18 teak wooden section with flat glass of 5mm thick. The Notice board shall have lining at back with approved shade of cloth, etc complete.The rate shall inclusive of the cost of all material ,transportation ,loading-un loading charges ,labour charges all accessories like knob,hinges etc as per drawing and directions of Engineer in charge. (refer the image in drawing no DP 1006 DRG CL 14 114) |
| 16 | OD228150/2025-2026: Manufacturing and supplying Reading Table of size 1800 (W) X 600 (D) x 750 (H)with following specification.The table top and gable end are made of 18mm thick teak wood of approved quality. The modesty panel is made of 18mm thick .The suface of the panel should be smoothly finished with approved polish like polyurathane ,ensuring a smooth ,even and uniform finish. All legs (straight) of 50mx50mm size are made of teak wood of approved .The rate shall be inclusive of cost of all material, transportation, loading - unloading charges,labour charges and accessories like nail bush 12 mm dia complete, as per manufatctures specification and directions of Engineer-In-charge at all levels. (refer the image in drawing no DP 1006 DRG CL 14 114) |
| 17 | OD228149/2025-2026:Manufacturing and supplying Teak wood office Table of size1500(W)X750(D)x750(H) with following specification.The tabletop are made of 15mmthick and backing shall be 12mm thick teakwood of approved quality. The side/storage panel is made of 18mm thick and draw bottom shall be 16mm thick .The straight leg of size 50x50 and foot rest of size 50x20 shall be teak wood of approved . The suface of the panel should be finished with approved polish like polyurathane, ensuring smooth even and uniform finish. .Two storage unit of size 400(W)x450(D)x715(H) has been considered.Two drawers unit of size 400(W)x150(D)x450(H) has been considered.Two key board tray with sliding facility is considered.The drawer will have a multipurpose lock of approved make with premium quality.The rate shall be inclusive of cost of material, transportation, loading-unloading charges,labour charges,all accessories like knob,lock, drawslider,nail bush25mmdia etc andcomplete,as per manufatctures specification and directions of Engineer-In-charge at all levels. (refer the image in drawing no DP 1006 DRG CL 14 114) |
| 18 | OD228148/2025-2026:Manufacturing and supplying Work Station of size1660(W)X1200(D)x1060(H) with following specification.The tabletop are made of 18 mmthick and backing shall be 15mm thick teakwood of approved quality. The side/storage/top panel is made of 18mm thick and draw bottom shall be 16mm thick . The suface of the panel should be finished with approved polish with like polyurathane,ensuring smooth even and uniform finish. .One storage unit of size 400(W)x450(D)x715(H) has been considered.One drawers unit of size 400(W)x150(D)x450(H) has been considered.One key board tray with sliding facility is considered. The drawer will have a multipurpose lock of approved make with premium quality. The rate shall be inclusive of cost of material, transportation, loading-unloading charges,labour charges,all accessories like knob,lock, drawslider,nail bush 25mmdia etc andcomplete,as per manufatctures specification and directions of Engineer-In-charge at all levels. (refer the image in drawing no DP 1006 DRG CL 14 114) |
| 19 | OD228147/2025-2026: Manufacturing and supplying Alamara (4 compartment) of size 1800x900x400mm with following specification.The storage side panels ,shelves ,top and bottom panels are made up of 15mm thick,backing shall be 12mm thick teak wood of approved quality.The door /shutter frame shall be made of 70x25mm shutter panelling with 5mm thick float glass. The surface shall be finished with approved polish like polyurathane, ensuring a smooth, even, and uniform finish.The handles are Satin SS finish of 160mm pitch. All hinges considered are premium make. Necessary good quality hardwares have been considered as required. The alamara will have a multipurpose lock of approved make with premium quality.The rate shall be inclusive of cost of all material ,accessories ,labour charges, transportation, loading - unloading charges and accessories like handle,nail bush 25mm dia etc complete, as per manufatctures specification, drawings and directions of Engineer-In-charge st all levels. (refer the image in drawing no DP 1006 DRG CL 14 114) |
| 20 | OD228146/2025-2026: Manufacturing and supplying Reading Table of size 1800 (W) X 900 (D) x 750 (H)with following specification.The table top and gable end are made of 18mm thick teak wood of approved quality. The modesty panel is made of 18mm thick .The suface of the panel should be smoothly finished with approved polish like polyurathane ,ensuring a smooth ,even and uniform finish. All legs (straight) of 50mx50mm size are made of teak wood of approved .The rate shall be inclusive of cost of all material, transportation, loading - unloading charges,labour charges and accessories like nail bush 12 mm dia complete, as per manufatctures specification and directions of Engineer-In-charge at all levels. (refer the image in drawing no DP 1006 DRG CL 14 114) |
| 21 | OD228144/2025-2026:Supplying mild steel (MS) L shaped book supporter made of 2.5mm thick MS sheet of size 102x203x135mm including cutting ,bending,welding ,grinding smooth of edges and painting one coat of metal primer and two coats of approved enamel paint including cost and conveyance of all materials,labour charges,lead,lift etc complete as directed by the Engineer in charge. |
| 22 | OD228162/2025-2026:Supplying High-grade lightweight aluminum alloy ladder of 1.8m (6 feet) length 100 kg to 150 kg including cost and conveyance of all materials,labour charges, lead,lift etc complete as directed by the Engineer in charge. Please Enable Macros to View BoQ information |
