|
| 1 | Drinking Water cooler 100-Ltr.capicity 2 nos. outlet push Toti provision with 60-LPH per hour R O , complete in all respect as per satisfaction of engineer in charge. |
| 2 | 25 MM EPDM Rubber Sport flooring granules including installation, transportation and GST charges complete in all respect to full satisfaction of Engineer-in-charge. |
| 3 | Specially Abled People Arm andTai Chi Wheel Fitness ApparatusProviding and fixing the following outdoor fitness equipment’s designed for minimum 100kg user Weight confirming to the required standard for safety and quality as perDIN/ASTM /CPSC/European standard / BIS The equipment shall be confirming to thespecification as below:-a) All the equipment shall be Third Party Quality certified as per the specifiedstandard.b) Nuts and Bolts- Stainless steel 316 and lock-nutc) Material – Galvanized steel Pipe cleaned by stand-blasting then coated withphosphate solution and finished with electro-static powder coating or othersimilar available material meeting the required standardd) Anti-rust Shoot blast /grit blasting of equipment to clean the rust Electrostaticpowder coating technique To process the pipe surfacee) Column the mild steel pipe column footing plate screw with a pull-burst, thesurface rust acid decreasing cleaning phosphate rust. After a special process,throwing sand imported plastic powder with a double surface household- levelspraying layer, electrostatic spray, high-temperature plastic 200 degree bakingpowder smooth surface UV resistant or as specified by the manufacture’sspecificationf) Seat and plastic LLDPE/HDPE metal with any protection / composite materialwith any protection infiltration of anti- static de-colorization element passing,strength, smooth surface, Security assurance weather resistant etc.g) UV-fully resistantPlatforms- High strength punching plate with special process dealing with wavy surfacemicroscopy, safe and beautiful non-slip resistanceFasteners – stainless steel screw to be used and at the contact point with the columns-rubbers pads to be used , screw top cover with a plastic cap, to enhance its security Theinstallation of the equipment’s shall be carried out on cement concrete foundation ofminimum size 700 mm x 700mm x 700 mm and / or size approved by Engineer-in- chargeof mix 1:1:5:3(1 cement 1.5 coarse sand 3 graded stone aggregate of 20 mm nominal size )The cost for equipment shall include the required foundation bolts of 18 mm dia and ofrequired shape and length as per sampleapproved by Engineer-in-charge however the cost for earthm work and CC shall be paid forseparately .The rates Quoted for the put door fitnessspecifications:-. Fabricated with main post of NB 100mm (G.I) “A” Class Pipe of approvedmake. Main frame of NB 65mm (G.I) “A” Class pipe. Handle support frame of NB 50mm (G.I)“A” Class pipe. (‘NB’ stands for Nominal Bore i.e., internal Diameter of pipe in millimetres).All pipes are powder coated with 80-120 micron thick Akzo Nobel or equivalent paints. Alljoints of pipe are robotic welded with joints scalloped as necessary and dressed off removingsharp edges and burrs. Zinc primer paint is applied at all the welding points prior tofinishing. Base plate cover made of virgin LLDPE plastic by rotational moulding withminimum 4.00mm thickness, UV resistant and coloured. Foothold made of NB 25mm (G.I)“A” Class pipe. Seat to be made up from virgin LLDPE plastic by rotational moulding withminimum 4.00mm thickness,coloured, UV resistant and environmental friendly.Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated areused in the equipment manufactured. The equipment are fitted with inbuilt limiters toprevent unwanted movements. The equipment is fixed on ground with concrete of minimumstrength M-25 and J shaped welded bolts of 18mm thickness. Once the concrete is set, theequipment is fixed on to it and nuts and bolts are covered with base plate cover. High tensilesteel with galvanized nut bolts are used for assembly.Equipment must be made and confirms with the approved standards certified by andcertificates are mandatory requires in the name of both Tenders act as bidder andmanufacturer.1. IS 178012. ISO 180013. ISO 27001:20134. ISO 50001:20185. ISO 13485:20166. ISO 45001:20187. ISO 14001:20158. ISO 9001:20159. ISO 14001:200410. ISO 9001:200811. EN 1490412. EN-1176-1-201713. EN 16630:201514. EN 1663015. EN 95716. EN 9100:201617. EN 11630:201718. GS19. DIN 18032.220. DIN 79000-201221. CE Certificate22. CE 1199323. OHSAS 18001:201724. SLBR 6225. BIFMA26. GMP27. RoHSThe equipment must accompained with Test report for Quality, Safety, Durability andProper Functioning of Equipment must mandatory requires Test report in the nameof both Tenderer act as bidder and manufacturer.1. Test Report of SS Nut and Bolts2. Test Report of LLDPE Base Caps for Open Gym3. Test Report of Powder Coating Pipe4. Test Report of SKF Bearing No. 6007-2Z5. Test Report of FRP/Plastic (Fiber Pad)6. Test Report of Welding Pipe (Robotic MIG Welding)7. Test Report of MEK Solvent8. Test Report of Neutrul Salt Spray Test9. Test Report of Breaking Load of Welding Pipe10. Test Report of GI Pipe 100 mm NB 11. Test Report of GI Pipe 80 mm NB12. Test Report of GI Pipe 50 mm NB13. Test Report of GI Pipe 32 mm NB14. Test Report of GI Pipe 25 mm NB |
| 4 | Specially Abled People Lat Pull Down and Tai Chi Wheel Fitness ApparatusThe handles hanging from the curved bar at the top are for lat pull-downs, which work theback and arm muscles.Lat shoulder Wheels:The two yellow discs are likely shoulder wheels, used for improving shoulder mobility andflexibility.8. ISO 9001:20159. ISO 14001:200410. ISO 9001:200811. EN 1490412. EN-1176-1-201713. EN 16630:201514. EN 1663015. EN 95716. EN 9100:201617. EN 11630:201718. GS19. DIN 18032.220. DIN 79000-201221. CE Certificate22. CE 1199323. OHSAS 18001:201724. SLBR 6225. BIFMA26. GMP27. RoHSThe equipment must accompained with Test report for Quality, Safety, Durability andProper Functioning of Equipment must mandatory requires Test report in the nameof both Tenderer act as bidder and manufacturer.1. Test Report of SS Nut and Bolts2. Test Report of LLDPE Base Caps for Open Gym3. Test Report of Powder Coating Pipe4. Test Report of SKF Bearing No. 6007-2Z5. Test Report of FRP/Plastic (Fiber Pad)6. Test Report of Welding Pipe (Robotic MIG Welding)7. Test Report of MEK Solvent8. Test Report of Neutrul Salt Spray Test9. Test Report of Breaking Load of Welding Pipe10. Test Report of GI Pipe 100 mm NB11. Test Report of GI Pipe 80 mm NB12. Test Report of GI Pipe 50 mm NB13. Test Report of GI Pipe 32 mm NB14. Test Report of GI Pipe 25 mm NBa) All the equipment shall be Third Party Quality certified as per the specifiedstandard.b) Nuts and Bolts- Stainless steel 316 and lock-nutc) Material – Galvanized steel Pipe cleaned by stand-blasting then coated withphosphate solution and finished with electro-static powder coating or othersimilar available material meeting the required standardd) Anti-rust Shoot blast /grit blasting of equipment to clean the rust Electrostaticpowder coating technique To process the pipe surfacee) Column the mild steel pipe column footing plate screw with a pull-burst, thesurface rust acid decreasing cleaning phosphate rust. After a special process,throwing sand imported plastic powder with a double surface household- levelspraying layer, electrostatic spray, high-temperature plastic 200 degree bakingpowder smooth surface UV resistant or as specified by the manufacture’sspecificationf) Seat and plastic LLDPE/HDPE metal with any protection / composite materialwith any protection infiltration of anti-static de-colorization element passing,strength, smooth surface, Security assurance weather resistant etc.g) UV-fully resistantspecifications:-. Fabricated with main post of NB 100mm (G.I) “A” Class Pipe of approvedmake. Main frame of NB 65mm (G.I) “A” Class pipe. Handle support frame of NB 50mm (G.I)“A” Class pipe. (‘NB’ stands for Nominal Bore i.e., internal Diameter of pipe in millimetres).All pipes are powder coated with 80-120 micron thick Akzo Nobel or equivalent paints. Alljoints of pipe are robotic welded with joints scalloped as necessary and dressed off removingsharp edges and burrs. Zinc primer paint is applied at all the welding points prior tofinishing. Base plate cover made of virgin LLDPE plastic by rotational moulding withminimum 4.00mm thickness, UV resistant and coloured. Foothold made of NB 25mm (G.I)“A” Class pipe. Seat to be made up from virgin LLDPE plastic by rotational moulding withminimum 4.00mm thickness,coloured, UV resistant and environmental friendly.Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated areused in the equipment manufactured. The equipment are fitted with inbuilt limiters toprevent unwanted movements. The equipment is fixed on ground with concrete of minimumstrength M-25 and J shaped welded bolts of 18mm thickness. Once the concrete is set, theequipment is fixed on to it and nuts and bolts are covered with base plate cover. High tensilesteel with galvanized nut bolts are used for assembly.Equipment must be made and confirms with the approved standards certified by andcertificates are mandatory requires in the name of both Tenders act as bidder andmanufacturer.1. IS 178012. ISO 180013. ISO 27001:20134. ISO 50001:20185. ISO 13485:20166. ISO 45001:20187. ISO 14001:2015 |
| 5 | Specially Abled People Outdoor Chest Press Fitness ApparatusProviding and fixing the following outdoor fitness equipment’s designed for minimum 100kg user Weight confirming to the required standard for safety and quality as perDIN/ASTM /CPSC/European standard / BIS The equipment shall be confirming to thespecification as below:-a) All the equipment shall be Third Party Quality certified as per the specifiedstandard.b) Nuts and Bolts- Stainless steel 316 and lock-nutc) Material – Galvanized steel Pipe cleaned by stand-blasting then coated withphosphate solution and finished with electro-static powder coating or othersimilar available material meeting the required standardd) Anti-rust Shoot blast /grit blasting of equipment to clean the rust Electrostaticpowder coating technique To process the pipe surface e) Column the mild steel pipe column footing plate screw with a pull-burst, thesurface rust acid decreasing cleaning phosphate rust. After a special process,throwing sand imported plastic powder with a double surface household- levelspraying layer, electrostatic spray, high-temperature plastic 200 degree bakingpowder smooth surface UV resistant or as specified by the manufacture’sspecificationf) Seat and plastic LLDPE/HDPE metal with any protection / composite materialwith any protection infiltration of anti- static de-colorization element passing,strength, smooth surface, Security assurance weather resistant etc.g) UV-fully resistantPlatforms- High strength punching plate with special process dealing with wavy surfacemicroscopy, safe and beautiful non-slip resistanceFasteners – stainless steel screw to be used and at the contact point with the columns-rubbers pads to be used , screw top cover with a plastic cap, to enhance its security Theinstallation of the equipment’s shall be carried out on cement concrete foundation ofminimum size 700 mm x 700mm x 700 mm and / or size approved by Engineer-in-chargeof mix 1:1:5:3(1 cement 1.5 coarse sand 3 graded stone aggregate of 20 mm nominal size )The cost for equipment shall include the required foundation bolts of 18 mm dia and ofrequired shape and length as per sample approved by Engineer-in-charge however the costfor earth work and CC shall be paid for separately .The rates Quoted for the put door fitnessequipment’s shall be inclusive of 1st Year comprehensive maintenancespecifications:-. Fabricated with main post of NB 100mm (G.I) “A” Class Pipe of approvedmake. Main frame of NB 65mm (G.I) “A” Class pipe. Handle support frame of NB 50mm (G.I)“A” Class pipe. (‘NB’ stands for Nominal Bore i.e., internal Diameter of pipe in millimetres).All pipes are powder coated with 80-120 micron thick Akzo Nobel or equivalent paints. Alljoints of pipe are robotic welded with joints scalloped as necessary and dressed off removingsharp edges and burrs. Zinc primer paint is applied at all the welding points prior tofinishing. Base plate cover made of virgin LLDPE plastic by rotational moulding withminimum 4.00mm thickness, UV resistant and coloured. Foothold made of NB 25mm (G.I)“A” Class pipe. Seat to be made up from virgin LLDPE plastic by rotational moulding withminimum 4.00mm thickness,coloured, UV resistant and environmental friendly.Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated areused in the equipment manufactured. The equipment are fitted with inbuilt limiters toprevent unwanted movements. The equipment is fixed on ground with concrete of minimumstrength M-25 and J shaped welded bolts of 18mm thickness. Once the concrete is set, theequipment is fixed on to it and nuts and bolts are covered with base plate cover. High tensilesteel with galvanized nut bolts are used for assembly.Equipment must be made and confirms with the approved standards certified by andcertificates are mandatory requires in the name of both Tenders act as bidder andmanufacturer.1. IS 178012. ISO 180013. ISO 27001:20134. ISO 50001:20185. ISO 13485:20166. ISO 45001:20187. ISO 14001:20158. ISO 9001:20159. ISO 14001:200410. ISO 9001:200811. EN 1490412. EN-1176-1-201713. EN 16630:201514. EN 1663015. EN 95716. EN 9100:201617. EN 11630:201718. GS19. DIN 18032.220. DIN 79000-201221. CE Certificate22. CE 1199323. OHSAS 18001:201724. SLBR 6225. BIFMA26. GMP27. RoHSThe equipment must accompained with Test report for Quality, Safety, Durability andProper Functioning of Equipment must mandatory requires Test report in the nameof both Tenderer act as bidder and manufacturer.1. Test Report of SS Nut and Bolts2. Test Report of LLDPE Base Caps for Open Gym3. Test Report of Powder Coating Pipe4. Test Report of SKF Bearing No. 6007-2Z5. Test Report of FRP/Plastic (Fiber Pad)6. Test Report of Welding Pipe (Robotic MIG Welding)7. Test Report of MEK Solvent8. Test Report of Neutrul Salt Spray Test9. Test Report of Breaking Load of Welding Pipe10. Test Report of GI Pipe 100 mm NB11. Test Report of GI Pipe 80 mm NB12. Test Report of GI Pipe 50 mm NB13. Test Report of GI Pipe 32 mm NB14. Test Report of GI Pipe 25 mm NB |
| 6 | Specially Abled People Arm extension Fitness ApparatusProviding and fixing the following outdoor fitness equipment’s designed for minimum 100kg user Weight confirming to the required standard for safety and quality as perDIN/ASTM /CPSC/European standard / BIS The equipment shall be confirming to thespecification as below:-a) All the equipment shall be Third Party Quality certified as per the specifiedstandard.b) Nuts and Bolts- Stainless steel 316 and lock-nutc) Material – Galvanized steel Pipe cleaned by stand-blasting then coated withphosphate solution and finished with electro-static powder coating or othersimilar available material meeting the required standardd) Anti-rust Shoot blast /grit blasting of equipment to clean the rust Electrostaticpowder coating technique To process the pipe surfacee) Column the mild steel pipe column footing plate screw with a pull-burst, thesurface rust acid decreasing cleaning phosphate rust. After a special process,throwing sand imported plastic powder with a double surface household- levelspraying layer, electrostatic spray, high-temperature plastic 200 degree bakingpowder smooth surface UV resistant or as specified by the manufacture’sspecificationf) Seat and plastic LLDPE/HDPE metal with any protection / composite materialwith any protection infiltration of anti-static de-colorization element passing,strength, smooth surface, Security assurance weather resistant etc.g) UV-fully resistantPlatforms- High strength punching plate with special process dealing with wavy surfacemicroscopy, safe and beautiful non-slip resistanceFasteners – stainless steel screw to be used and at the contact point with the columns-rubbers pads to be used , screw top cover with a plastic cap, to enhance its security Theinstallation of the equipment’s shall be carried out on cement concrete foundation ofminimum size 700 mm x 700mm x 700 mm and / or size approved by Engineer-in-chargeof mix 1:1:5:3(1 cement 1.5 coarse sand 3 graded stone aggregate of 20 mm nominal size )The cost for equipment shall include the required foundation bolts of 18 mm dia and ofrequired shape and length as per sample approved by Engineer-in-charge however the cost for earth work and CC shall be paid for separately .The rates Quoted for the put door fitnessequipment’s shall be inclusive of 1st Year comprehensive maintenancespecifications:-. Fabricated with main post of NB 100mm (G.I) “A” Class Pipe of approvedmake. Main frame of NB 65mm (G.I) “A” Class pipe. Handle support frame of NB 50mm (G.I)“A” Class pipe. (‘NB’ stands for Nominal Bore i.e., internal Diameter of pipe in millimetres).All pipes are powder coated with 80-120 micron thick Akzo Nobel or equivalent paints. Alljoints of pipe are robotic welded with joints scalloped as necessary and dressed off removingsharp edges and burrs. Zinc primer paint is applied at all the welding points prior tofinishing. Base plate cover made of virgin LLDPE plastic by rotational moulding withminimum 4.00mm thickness, UV resistant and coloured. Foothold made of NB 25mm (G.I)“A” Class pipe. Seat to be made up from virgin LLDPE plastic by rotational moulding withminimum 4.00mm thickness,coloured, UV resistant and environmental friendly.Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated areused in the equipment manufactured. The equipment are fitted with inbuilt limiters toprevent unwanted movements. The equipment is fixed on ground with concrete of minimumstrength M-25 and J shaped welded bolts of 18mm thickness. Once the concrete is set, theequipment is fixed on to it and nuts and bolts are covered with base plate cover. High tensilesteel with galvanized nut bolts are used for assembly.Equipment must be made and confirms with the approved standards certified by andcertificates are mandatory requires in the name of both Tenders act as bidder andmanufacturer.1. IS 178012. ISO 180013. ISO 27001:20134. ISO 50001:20185. ISO 13485:20166. ISO 45001:20187. ISO 14001:20158. ISO 9001:20159. ISO 14001:200410. ISO 9001:200811. EN 1490412. EN-1176-1-201713. EN 16630:201514. EN 1663015. EN 95716. EN 9100:201617. EN 11630:201718. GS19. DIN 18032.220. DIN 79000-201221. CE Certificate22. CE 1199323. OHSAS 18001:201724. SLBR 6225. BIFMA26. GMP27. RoHSThe equipment must accompained with Test report for Quality, Safety, Durability andProper Functioning of Equipment must mandatory requires Test report in the nameof both Tenderer act as bidder and manufacturer.1. Test Report of SS Nut and Bolts2. Test Report of LLDPE Base Caps for Open Gym3. Test Report of Powder Coating Pipe4. Test Report of SKF Bearing No. 6007-2Z 5. Test Report of FRP/Plastic (Fiber Pad)6. Test Report of Welding Pipe (Robotic MIG Welding)7. Test Report of MEK Solvent8. Test Report of Neutrul Salt Spray Test9. Test Report of Breaking Load of Welding Pipe10. Test Report of GI Pipe 100 mm NB11. Test Report of GI Pipe 80 mm NB12. Test Report of GI Pipe 50 mm NB13. Test Report of GI Pipe 32 mm NB14. Test Report of GI Pipe 25 mm NB |
| 7 | Specially Abled People Pull Chair with Cycle Combination Fitness ApparatusA pull chair, also known as a pull-wheelchair, combines the functionality of a standardwheelchair with a cycling feature, allowing the user to propel themselves using their handson the rear wheels. Cycle-handicapped wheelchairs, on the other hand, are typicallypowered by hand cranks.a) All the equipment shall be Third Party Quality certified as per the specifiedstandard.b) Nuts and Bolts- Stainless steel 316 and lock-nutc) Material – Galvanized steel Pipe cleaned by stand-blasting then coated withphosphate solution and finished with electro-static powder coating or othersimilar available material meeting the required standardd) Anti-rust Shoot blast /grit blasting of equipment to clean the rust Electrostaticpowder coating technique To process the pipe surfacee) Column the mild steel pipe column footing plate screw with a pull-burst, thesurface rust acid decreasing cleaning phosphate rust. After a special process,throwing sand imported plastic powder with a double surface household- level spraying layer, electrostatic spray, high-temperature plastic 200 degree bakingpowder smooth surface UV resistant or as specified by the manufacture’sspecificationf) Seat and plastic LLDPE/HDPE metal with any protection / composite materialwith any protection infiltration of anti-static de-colorization element passing,strength, smooth surface, Security assurance weather resistant etc.g) UV-fully resistantspecifications:-. Fabricated with main post of NB 100mm (G.I) “A” Class Pipe of approvedmake. Main frame of NB 65mm (G.I) “A” Class pipe. Handle support frame of NB 50mm (G.I)“A” Class pipe. (‘NB’ stands for Nominal Bore i.e., internal Diameter of pipe in millimetres).All pipes are powder coated with 80-120 micron thick Akzo Nobel or equivalent paints. Alljoints of pipe are robotic welded with joints scalloped as necessary and dressed off removingsharp edges and burrs. Zinc primer paint is applied at all the welding points prior tofinishing. Base plate cover made of virgin LLDPE plastic by rotational moulding withminimum 4.00mm thickness, UV resistant and coloured. Foothold made of NB 25mm (G.I)“A” Class pipe. Seat to be made up from virgin LLDPE plastic by rotational moulding withminimum 4.00mm thickness,coloured, UV resistant and environmental friendly.Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated areused in the equipment manufactured. The equipment are fitted with inbuilt limiters toprevent unwanted movements. The equipment is fixed on ground with concrete of minimumstrength M-25 and J shaped welded bolts of 18mm thickness. Once the concrete is set, theequipment is fixed on to it and nuts and bolts are covered with base plate cover. High tensilesteel with galvanized nut bolts are used for assembly.Equipment must be made and confirms with the approved standards certified by andcertificates are mandatory requires in the name of both Tenders act as bidder andmanufacturer.1. IS 178012. ISO 180013. ISO 27001:20134. ISO 50001:20185. ISO 13485:20166. ISO 45001:20187. ISO 14001:20158. ISO 9001:20159. ISO 14001:200410. ISO 9001:200811. EN 1490412. EN-1176-1-201713. EN 16630:201514. EN 1663015. EN 95716. EN 9100:201617. EN 11630:201718. GS19. DIN 18032.220. DIN 79000-201221. CE Certificate22. CE 1199323. OHSAS 18001:201724. SLBR 6225. BIFMA26. GMP27. RoHSThe equipment must accompained with Test report for Quality, Safety, Durability andProper Functioning of Equipment must mandatory requires Test report in the nameof both Tenderer act as bidder and manufacturer. 1. Test Report of SS Nut and Bolts2. Test Report of LLDPE Base Caps for Open Gym3. Test Report of Powder Coating Pipe4. Test Report of SKF Bearing No. 6007-2Z5. Test Report of FRP/Plastic (Fiber Pad)6. Test Report of Welding Pipe (Robotic MIG Welding)7. Test Report of MEK Solvent8. Test Report of Neutrul Salt Spray Test9. Test Report of Breaking Load of Welding Pipe10. Test Report of GI Pipe 100 mm NB11. Test Report of GI Pipe 80 mm NB12. Test Report of GI Pipe 50 mm NB13. Test Report of GI Pipe 32 mm NB14. Test Report of GI Pipe 25 mm NB |
| 8 | Specially Abled People Wave Balance Fitness Apparatus1. Size: 2386 x 136 x 1795mm2. Constructed with weather-resistant powder-coated steel and anti-slip wave-shaped foot platform.3. Platform length: 1800 mm: width: 400 mm: height variation simulates gentle wavemotion.4. Includes dual side handrails (height: 900 mm) with 42 mm diameter for stabilityand grip.5. Supports up to 150 kg user weight: fixed to ground with anti-rust anchor bolts.6. Enhances balance, coordination, and lower limb control for senior users in outdoorsettings.7. All the equipment shall be Third Party Quality certified as per the specifiedstandard.8. Nuts and Bolts- Stainless steel 316 and lock-nut9. Material – Galvanized steel Pipe cleaned by stand-blasting then coated withphosphate solution and finished with electro-static powder coating or othersimilar available material meeting the required standard10. Anti-rust Shoot blast /grit blasting of equipment to clean the rust Electrostaticpowder coating technique To process the pipe surface11. Column the mild steel pipe column footing plate screw with a pull-burst, thesurface rust acid decreasing cleaning phosphate rust. After a special process,throwing sand imported plastic powder with a double surface household- levelspraying layer, electrostatic spray, high-temperature plastic 200 degree bakingpowder smooth surface UV resistant or as specified by the manufacture’sspecification12. Seat and plastic LLDPE/HDPE metal with any protection / composite materialwith any protection infiltration of anti- static de-colorization element passing,strength, smooth surface, Security assurance weather resistant etc.13. UV-fully resistantPlatforms- High strength punching plate with special process dealing with wavy surfacemicroscopy, safe and beautiful non-slip resistanceFasteners – stainless steel screw to be used and at the contact point with the columns-rubbers pads to be used , screw top cover with a plastic cap, to enhance its security Theinstallation of the equipment’s shall be carried out on cement concrete foundation ofminimum size 700 mm x 700mm x 700 mm and / or size approved by Engineer-in- chargeof mix 1:1:5:3(1 cement 1.5 coarse sand 3 graded stone aggregate of 20 mm nominal size )The cost for equipment shall include the required foundation bolts of 18 mm dia and ofrequired shape and length as per sampleapproved by Engineer-in-charge however the cost for earthm work and CC shall be paid forseparately .The rates Quoted for the put door fitnessspecifications:-. Fabricated with main post of NB 100mm (G.I) “A” Class Pipe of approvedmake. Main frame of NB 65mm (G.I) “A” Class pipe. Handle support frame of NB 50mm (G.I)“A” Class pipe. (‘NB’ stands for Nominal Bore i.e., internal Diameter of pipe in millimetres).All pipes are powder coated with 80-120 micron thick Akzo Nobel or equivalent paints. Alljoints of pipe are robotic welded with joints scalloped as necessary and dressed off removingsharp edges and burrs. Zinc primer paint is applied at all the welding points prior tofinishing. Base plate cover made of virgin LLDPE plastic by rotational moulding withminimum 4.00mm thickness, UV resistant and coloured. Foothold made of NB 25mm (G.I)“A” Class pipe. Seat to be made up from virgin LLDPE plastic by rotational moulding withminimum 4.00mm thickness,coloured, UV resistant and environmental friendly.Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated areused in the equipment manufactured. The equipment are fitted with inbuilt limiters toprevent unwanted movements. The equipment is fixed on ground with concrete of minimumstrength M-25 and J shaped welded bolts of 18mm thickness. Once the concrete is set, theequipment is fixed on to it and nuts and bolts are covered with base plate cover. High tensilesteel with galvanized nut bolts are used for assembly.Equipment must be made and confirms with the approved standards certified by andcertificates are mandatory requires in the name of both Tenders act as bidder andmanufacturer.1. IS 178012. ISO 180013. ISO 27001:20134. ISO 50001:20185. ISO 13485:20166. ISO 45001:20187. ISO 14001:20158. ISO 9001:20159. ISO 14001:200410. ISO 9001:200811. EN 1490412. EN-1176-1-201713. EN 16630:201514. EN 1663015. EN 95716. EN 9100:201617. EN 11630:201718. GS19. DIN 18032.220. DIN 79000-201221. CE Certificate22. CE 1199323. OHSAS 18001:201724. SLBR 6225. BIFMA26. GMP27. RoHSThe equipment must accompained with Test report for Quality, Safety, Durability andProper Functioning of Equipment must mandatory requires Test report in the nameof both Tenderer act as bidder and manufacturer.1. Test Report of SS Nut and Bolts2. Test Report of LLDPE Base Caps for Open Gym3. Test Report of Powder Coating Pipe4. Test Report of SKF Bearing No. 6007-2Z5. Test Report of FRP/Plastic (Fiber Pad)6. Test Report of Welding Pipe (Robotic MIG Welding)7. Test Report of MEK Solvent8. Test Report of Neutrul Salt Spray Test9. Test Report of Breaking Load of Welding Pipe10. Test Report of GI Pipe 100 mm NB11. Test Report of GI Pipe 80 mm NB12. Test Report of GI Pipe 50 mm NB13. Test Report of GI Pipe 32 mm NB14. Test Report of GI Pipe 25 mm N |
| 9 | Specially Abled People Outdoor Fitness Ladder1. Constructed from powder-coated stainless steel with anti-corrosive finish foroutdoor durability.2. Ladder length: 2000 mm: rung spacing: 150 mm with 30 mm diameter rungs forsecure grip.3. Rungs coated with non-slip material to ensure safe climbing and grip.4. Mounted on a sturdy base with ground anchors for stability and safety.5. Designed to improve upper body strength, coordination, and mobility for speciallyabled users.6. All the equipment shall be Third Party Quality certified as per the specifiedstandard.7. Nuts and Bolts- Stainless steel 316 and lock-nut8. Material – Galvanized steel Pipe cleaned by stand-blasting then coated withphosphate solution and finished with electro-static powder coating or othersimilar available material meeting the required standard9. Anti-rust Shoot blast /grit blasting of equipment to clean the rust Electrostaticpowder coating technique To process the pipe surface10. Column the mild steel pipe column footing plate screw with a pull-burst, thesurface rust acid decreasing cleaning phosphate rust. After a special process,throwing sand imported plastic powder with a double surface household- level spraying layer, electrostatic spray, high-temperature plastic 200 degree bakingpowder smooth surface UV resistant or as specified by the manufacture’sspecification11. Seat and plastic LLDPE/HDPE metal with any protection / composite materialwith any protection infiltration of anti- static de-colorization element passing,strength, smooth surface, Security assurance weather resistant etc.12. UV-fully resistantPlatforms- High strength punching plate with special process dealing with wavy surfacemicroscopy, safe and beautiful non-slip resistanceFasteners – stainless steel screw to be used and at the contact point with the columns-rubbers pads to be used , screw top cover with a plastic cap, to enhance its security Theinstallation of the equipment’s shall be carried out on cement concrete foundation ofminimum size 700 mm x 700mm x 700 mm and / or size approved by Engineer-in- chargeof mix 1:1:5:3(1 cement 1.5 coarse sand 3 graded stone aggregate of 20 mm nominal size )The cost for equipment shall include the required foundation bolts of 18 mm dia and ofrequired shape and length as per sampleapproved by Engineer-in-charge however the cost for earthm work and CC shall be paid forseparately .The rates Quoted for the put door fitnessspecifications:-. Fabricated with main post of NB 100mm (G.I) “A” Class Pipe of approvedmake. Main frame of NB 65mm (G.I) “A” Class pipe. Handle support frame of NB 50mm (G.I)“A” Class pipe. (‘NB’ stands for Nominal Bore i.e., internal Diameter of pipe in millimetres).All pipes are powder coated with 80-120 micron thick Akzo Nobel or equivalent paints. Alljoints of pipe are robotic welded with joints scalloped as necessary and dressed off removingsharp edges and burrs. Zinc primer paint is applied at all the welding points prior tofinishing. Base plate cover made of virgin LLDPE plastic by rotational moulding withminimum 4.00mm thickness, UV resistant and coloured. Foothold made of NB 25mm (G.I)“A” Class pipe. Seat to be made up from virgin LLDPE plastic by rotational moulding withminimum 4.00mm thickness,coloured, UV resistant and environmental friendly.Maintenance free bearings of SKF or equivalent make duly oil sealed and self-lubricated areused in the equipment manufactured. The equipment are fitted with inbuilt limiters toprevent unwanted movements. The equipment is fixed on ground with concrete of minimumstrength M-25 and J shaped welded bolts of 18mm thickness. Once the concrete is set, theequipment is fixed on to it and nuts and bolts are covered with base plate cover. High tensilesteel with galvanized nut bolts are used for assembly.Equipment must be made and confirms with the approved standards certified by andcertificates are mandatory requires in the name of both Tenders act as bidder andmanufacturer.1. IS 178012. ISO 180013. ISO 27001:20134. ISO 50001:20185. ISO 13485:20166. ISO 45001:20187. ISO 14001:20158. ISO 9001:20159. ISO 14001:200410. ISO 9001:200811. EN 1490412. EN-1176-1-201713. EN 16630:201514. EN 1663015. EN 95716. EN 9100:2016 |
| 10 | Development of parks for person with special abilities near House no. 1440 sector 46 under Municipal Corporation Gurugram Please Enable Macros to View BoQ information |
