|
| 1 | Providing Ring bund & Bailing out water |
| 2 | OD19642/2024-2025:Putting up ring bund of top width 1.50m, bottom width 2.75m.and average height of 2.50mwith 1:1/4 side slope and protect the sides with coconut post of 4.50m long driving down2.00m below bed level at 75cm c/c, providing 3 rows of weiling pieces 1/4 split coconut poston both sides and 1/4 split cross ties to alternate posts at top, bottom and middle portionand screening the sides of bund with Seperation memebrane of impermeable plastic sheet125 micron thick fixed properly using coconut post and weiling pieces using reeper and nailsin full height including tying properly using iron wire and coir altogether and supply andfilling inside with hard clay/cut earth up to 2.50m, levell and conveyed with all leads andlifts including consolidating properly and maintaing the bund till the work is completed anddismantling the bund after completion of work etc. as per the directions of departmentalofficers at site.(As per approved data GO (RT) NO.6544/2021/FIN Dtd.06/10/21) Item No.5.3) |
| 3 | OD10014/2024-2025:Bailing out water using pump above 5 HP and Up to 10 HP-Bailing out water with engine and pump set above 5HP and up to 10HP, including conveyance to site and erection,cost of fuel, lubrication oil and other stores, pay of staff etc complete |
| 4 | Supply, Fabrication and erection of M S and S S embedded parts for shutters |
| 5 | OD10754/2024-2025:Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges |
| 6 | OD7640/2025-2026:Supply of MS round bar including cost of conveyance charges |
| 7 | OD31333/2024-2025:Fabrication, erection and commissioning of Structural steel Embedded parts in IS2062 Grade and accessories as per approved specifications, drawings and directions of deptl officer at site including cost of labour , machinery , incidental and handling charges etc complete but excluding cost of material already supplied |
| 8 | OD31318/2024-2025:Fabrication,Supply, erection and assembling in correct position and alignment by welding SS Embedded parts in 304L Grade like roller track, seal track,seal seat etc as per approved specifications,drawings and directions of deptl officer at site including cost of all materials,labour,machinery for planing, welding,shearing, grinding etc,lead and lift, conveyance, incidental and handling etc complete |
| 9 | Demolition and Re-concreting Works |
| 10 | 15.3:Demolishing R.C.C. work manually / by mechanical means including stacking of steel bars and disposal of unserviceable material with in 50 metres lead as per direction of Engineer -in-Charge. |
| 11 | 5.9.6:Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts |
| 12 | 5.33.2.2:Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cementAll work above plinth level upto floor V levelConcrete of M30 grade with minimum cement content of 350 kg /cum |
| 13 | 5.22.1:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelMild steel and Medium Tensile steel bars |
| 14 | Supply of materials, fabrication and erection of SS shutters |
| 15 | 85.105:Supply of SS plates of grade 304L including cost of conveyance charges |
| 16 | OD14885/2024-2025:Supply of SS bolt with nut and washer |
| 17 | OD32295/2024-2025:Supply of EN-8 pin for shutter |
| 18 | OD14899/2024-2025:Fabrication and supply of stainless-steel wheel gate in SS 304 L grade and accessories, etc. for the same as per approved specifications, drawings and directions of dept. officer at site including cost of labour, machinery for welding, shearing, grinding, etc., all lead and lifts, conveyance, incidental and handling, etc. complete but excluding cost of material already supplied. |
| 19 | OD38346/2024-2025:Fabrication and supply of Structural steel canal shutters ( Up to 2 tonne weight ) /Hoisting Bridge / Platform and accessories etc. for the same as per approved specifications, drawings and directions of deptl officer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc. complete but excluding cost of material already supplied |
| 20 | OD34093/2024-2025:Erection of the Canal Shutter ( up to 2 Tonne weight )/ hoist bridge/Platform including hand rails , ladder etc for the same including alignment correcting and setting complete including cost of all labour, machinery, incidental and conveyance , lead and lift charges etc complete but excluding cost of materials already supplied |
| 21 | Supplying and fixing 180mm dia Cast steel thrust rollers for SS shutters |
| 22 | OD31400/2024-2025:Supplying and fixing of Cast Steel thrust roller assembly consist of 180mm dia,50mm tread width with leaded tin bronze bush and 60mm roller axle(ss),including cost of all materials, conveyance and labour charges etc. complete as directed by the departmental officer at site. |
| 23 | Supply and fixing of flat type rubber seal at bottom side, angular type at vertical sides of shutters |
| 24 | 85.116:Supplying and fixing in correct position with specified initial interface the flat type rubber seal confirming to IS 11855 to the gates including cost of SS bolts and nut all labour and machinery and incidental and conveyance charges complete as per approved specification and drawing |
| 25 | 85.117:Supplying and fixing in correct position with specified initial interface the Angular type rubber seal confirming to IS11855 to the gates including cost of SS bolts and nuts and all labour and machinery and incidental and conveyance charges complete as per approved specifications and drawings |
| 26 | Supply of materials, fabrication, painting and erection of hoisting bridge and units for shutters |
| 27 | OD16079/2024-2025:Dismantling of the Canal Shutter ( Up to 2 Tonne weight ) / Hoisting Unit / Embedded parts etc. of the same and stacking at a distance of 100 meter including hire of machinery labour etc. complete as directed by the departmental officer at the site.(Weight of the unserviceable shutters and embedded parts may be calculated as 60% and unserviceable hoisting units as 80 % ) |
| 28 | OD12626/2024-2025:Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges |
| 29 | OD16150/2024-2025:Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges |
| 30 | OD32382/2024-2025:Supply of Aluminium chequered plates including cost of conveyance charges |
| 31 | OD33140/2024-2025:Supply of 32 mm dia GI pipes |
| 32 | OD32291/2024-2025:Fabrication and supply of Structural steel canal shutters ( Up to 2 tonne weight ) /Hoisting Bridge / Platform and accessories etc. for the same as per approved specifications, drawings and directions of deptl officer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc. complete but excluding cost of material already supplied |
| 33 | 85.115:Cost of painting with 2 coats of enamel paint over 1 coat of zinchromate primer as per IS1477:1994 after hand and power tool cleaning including cost of all materials, labour charges, cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site |
| 34 | OD33141/2024-2025:Supply of MS Bolts and Nuts |
| 35 | 16.70.1:Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts , bolts and washers as required complete as per the direction of Engineer-in- charge.Made of G.I. wire of dia 4 mm |
| 36 | OD16124/2024-2025:Erection of the Canal Shutter ( Up to 2 Tonne weight ) / Hoisting Bridge / Platformincluding hand rails , ladder etc. for the same including . alignment correcting and settingcomplete including cost of all labour, machinery, incidental and conveyance , lead and liftcharges etc complete but excluding cost of materials already supplied |
| 37 | Electrification of shutters |
| 38 | OD17103/2024-2025:Supply of a 1.5 kW (2 HP), 920 rpm, squirrel cage induction motor for hoist duty, TEFC, with Class ‘F’ insulation, operating on 400/440V, 3-phase AC, foot-mounted, conforming to IS 325, Frame Size: 100M, with shaft extension on both sides. |
| 39 | OD35943/2024-2025:Supply of worm reducer with a reduction ratio of 7.5:1, size 4", input power of 9.9 HP, input speed of 1000 RPM, output torque of 49 kgm, self-locking feature. |
| 40 | OD17178/2024-2025:Supply and fixing of dog clutch assembly including cost of materials, labour, conveyance etc complete. |
| 41 | OD32370/2024-2025:Providing a Double Worm and Pinion with a 1:12 ratio, an EN-8 pinion, a case-hardened cast steel wheel, a taper roller bearing for the pinion, and a thrust roller bearing for the gear, including the cost of all materials, labour, hire charges, and conveyance |
| 42 | 85.128:Providing Line shaft ,material : MS rolled/ forged steel |
| 43 | OD32372/2024-2025:Providing EN-8 screw rod 7.5 tonne capacity 4.00M lift screw hoist having one number of EN-8 Screw shaft having a lifting speed of around 5.00 cm/min for 24 rpm of hand operation including cost of all material,labour,hire charges and conveyance |
| 44 | OD17112/2024-2025:Installing the already supplied motor, worm reducer, and accessories in the correct position, and providing all the electrical connections, laying of wires, etc., complete with the cost of all materials, labor, conveyance, incidental expenses, etc. |
| 45 | Trial run of shutters |
| 46 | OD16130/2024-2025:Alignment and trial run of shutters including cost of all materials, labour charges and hire of machinery etc. complete for the smooth operation of the shutter both manually and electrical with generator. Please Enable Macros to View BoQ information |
