|
| 1 | Earthwork in excavation in foundation in all kinds of soil within initial lead of 50m. and 1.5m initial lift including rough dressing and breaking clods to maximum 5cm to 7cm and laying in layers not exceeding 0.3 mtr in depth etc complete as per the direction of the Engineer in Charge. |
| 2 | Providing and Laying of bored cast-in-situ M35 grade R.C.C. Pile of 1200 mm dia etc. complete as per Drawing and Technical Specifications and removal of excavated earth with all lifts and lead upto 1000 m. etc. as per specific ation & direction of the Engineer-in Charge |
| 3 | Providing and laying Steel liner of 8 mm thick in pile including Fabricating and setting out as per detailed drawing etc.complete as per the direction of the Engineer in Charge. |
| 4 | Sinking of steel liner plate for pile including cost of all labour & machinery etc complete as per specification & direction of the Engineer in charge. |
| 5 | Reinforced Cement Concrete M 35 Grade using 20mm down graded chips in superstructure etc. complete as per specific ation & direction of the Engineer-in Charge. |
| 6 | Pile Cap |
| 7 | Supplying, Providing & laying reinforced cement concrete M-15 grade (cast-in-situ) as per design mix prepared under relevant IS/IRC codes concrete using graded crushed stone aggregate, cement and coarse sand of approved quality and quantity in wing walls, retain walls & curtain walls as levelling course using weigh batching, mechanically mixing, vibrating, centering & shuttering, decentering secured tools & plant equipments & including all inclusive costs, all operations, contingencies incidentals involved for the finished defect free items of work complete to satisfaction but excluding cost of reinforcement complete as per drawing and technical specification Part I/II under section 1500,1700 & 2100 of MORTH specification for Road & Bridge works (4th revision) and as directed by Engineer or his representative full satisfaction.Providing PCC M15 as leveling coarse below pile caps & as per section no.1500,1700 & 2100 of Specification for road & bridge work MoRT&H (4th revision) |
| 8 | Filling sand in foundation in trenches as per drawing and technical specification etc. complete as per specific ation & direction of the Engineer-in Charge. |
| 9 | Reinforced Cement Concrete M 30 Grade using 20mm down graded chips in superstructure etc.complete as per direction of Engineer-In-Charge. |
| 10 | Abutment & Pier Shaft |
| 11 | Abutment & Pier Cap |
| 12 | Column, Wing Wall & Tie beam |
| 13 | Dirt Wall |
| 14 | Superstructure |
| 15 | Approach Slab |
| 16 | Providing & laying of wearing course of 56mm thick consisting of 6mm thick mastic asphalt and 50 mm thick asphaltic concrete on top of the Deck slab. The mastic asphalt shall be of paving grade bitumen meeting the requirement given in the table 500-39, prepared by using mastic cooker and laid to required level & slope after cleaning the surface, applying prime coat including providing antiskid surface with bitumen precoated fine grained hard stone chipping all complete as per clause 501, 502, 503 & 516 of MoRT&H Specification for road & bridge works (5th revision), followed by asphaltic concrete to be laid in two layers of 25mm thick each over tack coat etc complete as per approved drawing & technical specification Clause No 503 & 507 of MoRT&H specifications for road & Bridge work (5th revision) and as per direction of the Engineer-in-charge. |
| 17 | Provision and Reinforced cement concrete crash barrier at thr bridge desk & approches to bridge structure, constructed with with reinforced cement concrete with HYSD Reinforcement conforming MoRth specification and as per detail given IRC - 5 including dowel bar, Expansion Joint filled with pre- moulded asphalt filler board etc. and approved drawing and at location directed by the engineer all as specified. |
| 18 | Providing HYSD bars confirming to approved grade F-415 including all labours for cutting ,bending, binding, lapping, splicing, welding etc. (conforming to ISI specification) & jointing if necessary by lapping & tying the grills & placing in position as required for RCC works as per the approved design, hoisting, lowering & laying position including cost & conveyance of tor steel & binding wires of 18 to 20 gauge(as to be approved by the Deptt.) etc. complete with Cess in all respect (weight of binding wire shall not be considered for payment at all which will be borne by the contractor) as per specification and direction of the Engineer in charge. |
| 19 | Providing 600 mm thick Filter media with stone crushed aggregates of 45 mm size satisfying the requirements laid down in clause 2504.2.2. of MoRTH specifications to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and provided over the entire surface behind abutment , wingwall and return wall to the full height compacted to a firm condition complete as per drawing and Technical Specifications. |
| 20 | Providing weep holes in the abutment & wing walls 8.00cm. X 23.00cm. size including metal spall backing 30cm X 30cm. size in rear complete as per the approved design & drawing including providing centering & shuttering with cost, conveyance, royality & taxes of all materials T&P articles etc. complete in all respects as per specification & direction of the Engineer-in-Charge. |
| 21 | Providing Rough stone dry packing / pitching in slope, protection walls, approns and revetments to designed thickness using hard granite stones of required size of approved quality from approved quarry including quarrying supplying conveying and cost conveyance taxes royalty of all materials including complete including filling the interstices with small stones by wedging and hammering finished to proper slope and level as per direction of the Engineer – in – charge including dewatering if required. |
| 22 | Back filling behind abutment, wing wall & return wall with granular material including all cost, carriage, royality & labour as per specification & direction of the Engineer-in-Charge. |
| 23 | Gravel Backing |
| 24 | Sandy Material |
| 25 | Supplying, Transporting and fixing Reinforced cement concrete (1:2:4) Circular Guard Posts (Size 0.15m dia at bottom & 0.10 M dia at Top of 1.20 m long) of standard design fixed in position including finishing and painting etc. complete as per direction of the Engineer-in-charge. |
| 26 | Providing and laying of compression seal joint consisting of steel armoured nosing at two edges of the joint gap suitably anchored to the deck concrete and a preformed chloroprene elastomer or closed cell foam joint sealer compressed and fixed into the joint gap with special adhesive binder to cater for a horizontal movement upto 40 mm and vertical movement of 3 mm etc. complete as per direction of Engineer-in-charge. |
| 27 | Cement concrete (1:3:6) in foundation & plinth with 4cm. crusher broken granite metal of approved quality from approved quarry including hoisting lowering & laying in layers not exceeding 150mm. thick with proper packing & ramming each layer of concrete by means of vibrator ,providing groove & beads where necessary including curing, dewatering, shoring, shuttering if necessary at the time of laying concrete with cost, conveyance royality & taxes of all material required for the work including supplying & working pumps, T&P articles finishing the exposed surface smooth as per specific ation & direction of the Engineer-in Charge |
| 28 | Below approach slab |
| 29 | Supply and fixing of the POT / PTFE Bearing procured from approved manufacturer & with test certificates as per specification provided in drawing at location with all accessories complete & fixing on abutment and piers in position with all materials, labour, tools, equipment for fixing as per drawings and technical specifications part I/II, section 2000 & its relevant clauses & sub clauses of MoRTH specification for Road & Bridge works (4th revision) as directed by Engineer/or his representative to satisfaction. |
| 30 | Providing & Fixing drainage spout with 100mm dia GI pipe in deck slab with MS grating as per Clause-2705 under Section 900, 2700 of MORT&H specifications for Road & Bridge works (5th Revision) and as per direction of Engineer-in-Charge. |
| 31 | Providing and applying two coats of water based enamel paint to unplastered concrete surface after cleaning the surface of dirt, dust, oil, grease, efflorescense and applying paint @ 1 litre per 02 Sqm |
| 32 | Providing and applying two coats of water based enamel paint to unplastered concrete surface after cleaning the surface of dirt, dust, oil, grease, efflorescense and applying paint @ 1 litre per 02 Sqm |
| 33 | Dismetalling of existing structures like culverts, bridges, retaining walls and other structure comprising of masonary, cement concrete, wood work, steel work, including T&P and scaffolding whereever necessary, sorting the dismentalled material, disposal of unserviceable material and stacking the serviciable material with all lifts and lead of 1000 m as per Technical Specification Clause 202.1 |
| 34 | Clearing grass & removal of rubbish on both sides of the road to facilitate widening berms , disposal of stuff including all labours , T&P article as per specification for road & bridge work. |
| 35 | Construction of embankment with approved material obtained from borrow pits with 5 extra lead lifts and leads, transporting to site by mechanical means within a lead of 5kms, spreading, grading to required slope and compacting to meet requirement of table 300-2 & clause 305 of MoSRT&H Specifications for Road & Bridge works (4th Revision)and as per the direction of engineer in charge. |
| 36 | Loosening of the ground upto a level of 500mm below the sub-grade level, watered, graded and compacted in layers to meet requriement of table 300-2 for sub-grade construction and clause 305 of MoRT&H Specifications for Road & Bridge works (4th Revision) |
| 37 | Construction of granular sub-base by providing Close graded Granular subbase Grading-III material as per table 400-1, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density complete as per Clause 401 of MoSRT&H Specifications for Road & Bridge works (4th Revision) |
| 38 | Providing, laying, spreading & compacting graded stone aggregate to Wet Mix Macadam specification including pre mixing the material with water at OMC in mechanical mix plant, carriage of mixed material by tipper to site, laying in uniform layers with paver in sub base/base course on well prepared surface & compacting with vibratory roller to acieve the desired density as per clause 406 of MoSRT & H specifications for road & bridge works.(4th Revision) |
| 39 | Construction of un-reinforced, plane cement concrete pavement of desired, thickness as per thee design, over a prepaired sub base, with 43 grade cement or any other type as per cluse 1501.2.2 M30 (Grade), course and fine aggregate conforming to IS:383, maximum size of course aggregate not exceeding 25mm, mixed in a concrete mixture of not less the 0.2 cum capacity and appropriate weight batcher using the approved mix design, laid in approved fixed side form work (steel channel, laying and fixing of 25mm micro thick polythene film, wedges steel plates including levelling the form work as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrator and finished in the contineous operation includion provision of construction and expansion, construction joint, applying debonding strips, primer, sealant, near approaches to bridge/culvert and construction joints, admixture as approved, curing of concrete slabs for 14-days, water finishing to lines and grade as per drawing and Technical Specification cluse 1501.panels are to be made by cuttion grooves of 3 to 5 mm thick and 25 to 30 mm deep in CC Slab. The grooves are to be filled with VG-30 Bitumen with a spray of fine sand at top. |
| 40 | Furnishing and laying of the live sods of perennial turf forming grass on embankment slope, verges or other locations shown on the drawing or as directed by the engineer including preparation of ground, fetching of sods and watering as per technical specification |
| 41 | Providing Concrete for Plain/ reinforced concrete in open foundation complete as per drawing and technical specifications Clauses 802,803,1202 & 1203 |
| 42 | Bottom portion |
| 43 | Top portion |
| 44 | Unit cost of NP3 hume pipes including cost of labour for laying hume pipes (1000 mm dia.) etc. complete as per direction of the Engineer-in-charge Please Enable Macros to View BoQ information |
