|
| 1 | 14.23 Dismantling old plaster or pointing, raking out joints, cleaning and preparing the surface for re-plastering or re-pointing including disposal of rubbish to the dumping ground with all leads and lifts etc.complete as per direction of the Engineer- in-charge. |
| 2 | Providing and laying in position cement concrete of specified grade excluding the cost of centring andshuttering - -All work upto plinth level:1:3:6 ( 1 Cement: 3 fine sand : 6 graded well burnt brickaggregate 20 mm nominal size) |
| 3 | Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6mm angle iron and 3mm M.S. gussetplates at the junctions and corners, & with cleats with bolts & nuts, rivets, locking arrangement, handles, hooks& eyes, pinlets including embedding in cement concrete of required grade for fixing in position, all necessary fittings, including applying a priming coat of approved steel primer etc. complete as required:-Using M.S. angels 40x40x6 mm for diagonal braces. |
| 4 | 12 mm cement plaster of mixCement mortar 1:4 (1 cement : 4 fine sand) |
| 5 | 15 mm cement plaster on the rough side of single or halfbrick wall of mix:Cement mortar 1:4 (1 cement : 4 fine sand) |
| 6 | Grading roof for water proofing treatment complete as required as per direction of the Engineer-in-charge with :a)Cement mortar 1:4 (1cement : 4 fine sand) |
| 7 | Distempering with dry distemper of approved brand and manufacture (two or more coats) of required shade on new work, over and including water thinnable priming coat to give an even shade. [Payment shall be made after submission of Test Certificate issued by the Manufacturer] |
| 8 | Finishing walls with acrylic smooth exterior paint of required shade of approved brand and manufacture[Payment shall be made after submission of Test Certificate issued by the Manufacturer] |
| 9 | Finishing with Epoxy paint ( two or more coats) of approved brand and manufacture at all locations prepared and applied as per manufacturer'sspecification including appropriate priming coat, preparation of surface etc.complete [Payment shall be made after submission of Test Certificate issued by the Manufacturer]. On steel work |
| 10 | Neat Cement Punning |
| 11 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm sand cast Iron P or S trap,10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures completeincluding cutting and making good the walls and floors wherever required : |
| 12 | Providing and laying 1st class quality vitrified floor tiles in different sizes (thickness to be specified by themanufacturer) with water absorption less than 0.08% and conforming to IS: 15622 - 2017, of approved make, in allcolours and shades, laid over 20mm thick cement mortar 1:4 (1 cement : 4 fine sand), jointing with grey cementslurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc. all complete asper direction of the Engineer-in charge.Glazed Vitrified Tiles (Glossy / Mat Finish/ Anti-Skid).Size of tile 600 mm x 600 mm |
| 13 | Providing and fixing Precast chequered cement concrete tiles 18 mm thick, laid in footpath & courtyard, on 20mm thick bed of cement mortar 1 : 4 ( 1 cement : 4 fine sand ) jointed with neat cement slurry including rubbing and cleaning etc. all complete as per direction of Engineer-in-charge.In dark shade using ordinary cement |
| 14 | Providing and fixing G.I. pipes of medim class as per IS : 1239 with latest amendment complete with G.I.fittings and clamps, including cutting and making good the walls etc. complete as per CPWD specification and direction of the Engineer - in - charge. Internal work - Exposed on wall.25 mm dia. nominal bore |
| 15 | Providing and fixing G.I. pipes of medim class as per IS : 1239 with latest amendment complete with G.I.fittings including trenching and refilling etc. complete as per CPWD specification and direction of theEngineer - in - charge. External work.25 mm dia. nominal bore metre . |
| 16 | Making connection of G.I. distribution branch with G.I. main following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete as per CPWD specification and direction of the Engineer - in - charge. 25 to 40 mm nominal bore each . |
| 17 | Providing and fixing brass bib cock of approved quality : 15 mm nominal bore . |
| 18 | Providing and fixing soil, waste and vent pipes: 100 mm dia. Sand cast iron S&S pipe as per IS: 1729. |
| 19 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste ofstandard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require :White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps |
| 20 | Providing and fixing on wall face unplasticised Rigid PVC rain water, soil, waste & vent pipes (workingpressure 6 kg / cm2) conforming to IS : 13592 Type A including jointing with seal ring conforming to IS :5382 leaving 10 mm gap for thermal expansion:Single socketed pipe - 110 mm OD |
| 21 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement andmaking necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 22 | Constructing soak pit 1.20 x 1.20 x 1.20 m filledwith brickbats including S.W. drain pipe 100 mmdiameter and 1.20 m long complete as perstandard design Please Enable Macros to View BoQ information |
