|
| 1 | Earth work excavation for foundation in Hard stiff clay, stiff black cotton, hard red earth, shales murram, gravel,stoney earth and earth mixed with small size boulders SS.20B and Sand,silt or other loose soil, wet sand,or silt not under water, light black cotton soil, sandy loam ordinary soil and initial lead of 10m initial lift of 2 mto full depth as may be directed except in hardrock requiring blasting inclusive of shoring shuttering etc.,complete |
| 2 | Supplying and filling in foundation and basement with stone dust in layers of not more than 15cm thick well rammed watered and compacted etc., complete complying with standard specification. |
| 3 | Supplying and filling the basement with Good Earth filling in layers of not more than 15cm thick well rammed watered and compacted - etc., complete complying with standard specification. |
| 4 | Plain Cement concrete 1:4:8 (one cement, four sand, eight aggregate) using 40mm gauge hand broken granite stone jelly for foundation including dewatering if found necessary and laid in layers of not more than 15 cm thick and compacted,etc., complete complying with standard specfication. |
| 5 | Brick work in CM 1:5 (one cement & Five Crushed Stone Sand (M- Sand)) using II class ground moulded bricks of size 9\\" X 43/8\\"X 2 3/4\\" including finishing, curing, etc., complete complying with standard specification - 100CFT |
| 6 | Plastering with cement mortar 1:5 (One part of Cement and Five part of Plastering Sand (P- Sand)) 12mm, thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications |
| 7 | Painting two coats for Exterior surface with approved Exterior Plastic Emulsion paint approved quality and colour over a priming coat, including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification. |
| 8 | Centering for soffits of RCC slabs of plane surface like lintels, beams ,etc.,including strutting 3m high using mild steel sheets of size 90cm X 60cm X and B.G 10 stiffened with M.S angles of size 25mm X 25mm X 3mm laid over silver Oak (C.W) joists of size 10cm X 6.5cm (spaced at about 90cm c/c )and supported dy casurina props of 10cm to 13cm dia (spaced of 75cm C/C) complying with standard specification and directed - 10 m 2 (P & D)Data 38 |
| 9 | Suppling and fabricating and placing in position MS (or) R.T.S. bar for reinforcement to all RCC works as per the design given including cost of steel and binding wire also in all floors. |
| 10 | Providing and laying in position Standardised Concrete Mix M-20 Grade in accordance with IS 456 - 2000 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement contenet of 325Kg/ cum and maximum water cement ratio of 0.55 including admixture (Plasticiser / super plasticiser) in recommended proportions as per IS 9103 to accelerate, related setting of concrete, improve workability without imparing strength and durability with about (5.0cum), 7730Kg of 20mm machine crushed stone jelly and with about (3.3 cum), 5156kg of 10 - 12mm machine crushed stone jelly and with about (4.79cum) 7670 kg of Crushed Stone Sand (M- Sand), but excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary without claiming extra cost etc., complete complying with standard specification and as directed by the departmental officers - |
| 11 | Supply and fixing of M.S Grills with Doors and Windows with one coat of Red oxide with Primer including all costs such as welding,grinding and fabrication charges, cost and conveyance of all materials to site etc,complete as per standard specification. |
| 12 | Painting two coats with Ready Mixed Enamel Paint over the new iron works of approved quality and colour without priming coat including the cost all materials etc.,complete, in all floors. |
| 13 | Supplying and fixing in position Cement based hydrualically pressed Anti-Skid tiles (pattern design) 20mm thick in cement mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 20mm thick and pointed with same colour of cement etc., complete as per standard specification |
| 14 | Dadooing walls with ceramic tiles of sizes 300mm X 450mm X 8mm size of approved make and quality and colour Set in cement mortar 1:2 (One part of Cement and two part of Plastering Sand (P- Sand)) over 10 mm base layer plastering and pointing with white cement neatly as directed. |
| 15 | Paving the floor with pre-polished Concrete Anti-Skid step tiles (Required shape and design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One part of Cement and Three part of Plastering Sand (P- Sand)), 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg/sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. |
| 16 | Supplying and planting of Korean grass including application of organic manure in proper ratio for required base and application of lindane or equivalent chemical for the control of pest and disease and providing root regulated chemical like neem cake, DAP and super phosphate and planting the grass including watering weeding labour, tools cost including all costs etc., complete as per instructed by the departmental officers. |
| 17 | Supplying and fixing of Double Swing of height 2.40m height with 40mm dia M.S. pipes support as legs and top bar is 50mm dia. The seat is 9mm thick reinforced rubber with Antiskid chequred top with heavy ball bearing and the suspension is 7mm dia electro galvanized chain and the cost shall inclusive of all materials, labours and fixing etc, complete as directed by the departmental officers. |
| 18 | Supplying and fixing of Two seater SeeSaw for below 12 years old childrens to a height of 0.50m with 50mm dia leaver and 40mm top bar with M.S. Pipes. The seater is of moulded plastic with heavy duty bush bearing. The cost shall inclusive of all materials, labours and fixing etc, complete as directed by the departmental officers. |
| 19 | Supplying and fixing of Slide for below 12 years old childrens to a length of 3.00m with 80mm dia leaver and 40mm top bar with M.S. Pipes. The seater is of moulded plastic. The ladder frame is made up of 25mm M.S.Pipe, hanrail 20mm dia M.S. Pipe and the centre support is 80mm dia M.S. Pipe The cost shall inclusive of all materials, labours and fixing etc, complete as directed by the departmental officers. |
| 20 | Supplying and fixing of Jungle Gym for below 12 years old childrens to a height of 2.10m with 80mm dia leaver and 40mm top bar with M.S. Pipes. The ladder frame is made up of 25mm M.S.Pipe, hanrail 20mm dia M.S. Pipe and the centre support is 80mm dia M.S. Pipe The cost shall inclusive of all materials, labours and fixing etc, complete as directed by the departmental officers. |
| 21 | Supply and fixing of 8m Free Standing Single Arm Bracket 8 sided Octogonally continously tapered structured pole with base plate of size 300 x 300 x 12mm as per IS-875 with following specification.Bottom Pole Dia - 130mm Top Pole Dia - 70 mm Thickness of Pole - 3 mm The pole should be hot dip galvanized confirming to BESN ISO-1461 with thickness of 65 Micron With 3 core 4sq.mm PVC copper UG cable including 48W led street light all labour charges |
| 22 | Providing Three Seater arrangements with Granite Slabs of 20mm thick over the 100mm thick Precast Slab with 230mm thick, 600mm height side walls and Plastered with C.M. 1:5, 12mm thick, white washing two coats. The cost shall include all labour and materials and as directed by the departmental officers. |
| 23 | Supply and delivery of Animal sculptures using necessary accessories with fibre materials model not less than 2 m height required including cost and conveyance of all materials and incidiancial charges etc., complete as per the standard spcification. (Elephant, Deer, Giraffe, Hourse) |
| 24 | Providing various desings of Animal Dust Bins made of 3 layer fiber structures with multi colour powder coating. The height of the dust bins 4 feet. Available models are Penguin, Rabbit, Fish & Monkey cost including all costs, transporation charges and all other incidental charges etc., cost including all cost etc., complete as per instructed by the departmental officers. |
| 25 | Supply and delivery and fixing of HDPE tank 2000 litres capacity as per IS 12701 / 1996 including loading, unloading, transportation and labour charges for fixing of the GI pipes and specials for pipe connection works including cutting, threading and fixnig charges as directed by TWAD Board officers etc., |
| 26 | Supply and fixing of CCTV camera with 8 units with following specifications as instructed by the departmental officers, cost including all cost and conveyance of all materials to site, labour charges and other incidental charges taxes etc., completeA. 1.3 MP HD Bullet camera HD sensor 3.6mm 1080 lens 36 IR high sensivive LED, 25M distance IR with heat absorbing filter & day/ night sensor.B. 1080P-8 channel HD DVR 8 channel video, 4 channel audio 1 VGA output, 1 HDMI output, USB mouse and remote / mobile view and maximum 4 TB HDD connectivity with 1 SATA port (without hard disk). C. 4 TB WD SATA purple surveilance hard disk.D. 8 channel SMPS. E.NC & DC Connector. F.LG Monitor 22 inches G.Service Charges. H. 8 U mounted rack with glass door with two year warranty for camera, DVT, hard disk monitor. MR |
| 27 | Providing and erecting of Retro - Reflectorised Cautionary, Mandatory and Informatory signs (without definition board) made out of High Intensity Prismatic Grade Sheeting confirming to Type-IV standards of IRC-67: 2022 and ASTM D 4956 –09, specification and fixed over 2mm thick Aluminium sheet fixed over a back supporting frame of 25mm x 25mmx3mm Mild Steel angle and supported on a mild steel angle post 75X75X6mm with a clear height of not less than 2.10m from the ground level to the bottom of the sign board and 0.60m below ground level. The sign post should be painted as per IRC 67-2022 and firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cmX45cmX60cm size including cost and conveyance of all materials, equipment, Machinery and labour with all leads and lifts, loading charges necessary for satisfactory completion of the work as directed by the engineer-in-charge. High intensity Retro - Reflectro sheet shall consist of minimum coefficient of Retro-reflection as per Table 6.6 of IRC 67-2022. The retro - reflective sheeting shall be covered under 7 year warranty issued for field performance and a certified copy of three years outdoor exposure report shall be obtained as per IRC 67:2022. (as per MoRT&H Specification No.801) 60 cm x 45 cm rectangular |
| 28 | Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase near wet riser using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick will be provided with tubular supports made of 304L Grade Stainless Steel pipe of 25mm dia of 1.60mm thick welded to the railing. The supports will be grouted into the wall and provided with 93.00mm thick Stainless Steel circular base plate of 304 Grade. The rate shall included for grouting into concrete with necessary supporting arrangements the hand rail in floor polishing buffing, bonding, cutting, grinding, conveyance, welding charges, electrical charges, etc. complete |
| 29 | Providing Entrance arch using all requird materials and labour inclding cost and conveyance all materials and as directed by the departmental officers etc., complate as per the standard specification. MR |
| 30 | Towards cost of Geophysical investigation survey charges. |
| 31 | Supply and delivery of 200mm dia of (Casing medium) PVC casing plain pipe including cost and conveyance at site etc., complete as per standard specification (Twad S no 1.1 pg.no 22) |
| 32 | Supply and delivery of 150mm dia of (Casing medium) PVC casing Slotted pipe ( Company Slots) including cost and conveyance at site etc., complete as per standard specification ISI make (Twad S no 1.1 pg.no 22) |
| 33 | Supply and delivery of 150mm dia of (Casing medium) PVC casing plain pipe including cost and conveyance at site etc., complete as per standard specification `(Twad S no 1.1 pg.no 22) |
| 34 | Drilling of 200mm dia bore wells any where is chengalpattur district including tranportion from one place to aother place with in this district in alluvial soil or sedimentrary starata using rotary rig by first drilling a pilot bore of 150 mm dia by direct rotary mud circulation method using contractors rig tool fuel, labour drillng bentonite mud and water required for drilling, |
| 35 | Drilling 150mm dia pilot bore to the required depth Below ground level.(Twad S no 12 pg.no 302) |
| 36 | Drilling 150mm dia pilot bore up to 60 m to 90 m from Ground level.(Twad S no 12 pg.no 302) |
| 37 | Drilling 150mm dia pilot bore up to 90 m to 120 m from Ground level.(Twad S no 12 pg.no 302) |
| 38 | Drilling 150mm dia pilot bore up to 120m to 150 m from Ground level.(Twad S no 12 pg.no 302) |
| 39 | Drilling 150mm dia pilot bore up to 150m to 180 m from Ground level.(Twad S no 12 pg.no 302) |
| 40 | Supply and delivery of 200mm dia(8”) PVC end cap including cost and conveyance etc., complete (Twad Sor 1.5 pg.no 27) |
| 41 | Reaming from 150mm dia pilot bore to 200mm dia size bore as directed by the Departmental Officer, to the required depth up to 60 from Ground level (Twad Sor WD-W0771) |
| 42 | Labor charges for inserting the P.V.C. casing pipes assembly with slots (or) without slots in the drilled holes including joining the pipes etc., complete, supply and packing the annular space with pebbles of size and quality as approved by the Municipal Engineer excluding cost of casing pipe etc., complete 200mm dia PVC casing pipe (Twad Sor WD-W0772) |
| 43 | Charges for developing the bore wells with Air Compressor 600cfm (Minimum 8 hours) including transportation labor and fuel charges for Compressor as directed by the Departmental Officer and conducting yield test by “V” notch method.(Twad Sor WD-W0772) |
| 44 | Supply and Fixing of 5 HP Motor Submersible Pump set ISI mark IS 8034Without panel board 75LPM and 60M Head including Fixing Charges and all Charges etc. Complete.(Rate with TNVAT @4% on Basic cost Excise Duty)(Sor S no 408 pg.no 105) |
| 45 | Supply and delivery of suitable 3 phase panel board to 5HP with DOL Starter Auto On/Off Switch etc.,(Twad Sor S no 112 pg.no 115) |
| 46 | Supply and Delivery of 2.5 Sqmm PVC insulated and Sheathed 3 Core flat type copper cable confirming to IS 694/1990 Including all charges with excise duty and handling charges etc (Twad Sor WD-M2000) |
| 47 | Towards Labour Charges for the errection of Submersible pump set in bore well including fixing and jointing submersible cable with proper clamps up to the starter to riser pipes to the required depth valves erection clamps, pressure gauge up to the exterior of panel board consisting of TPICN switches starter ,Volt meter, Ammeter, three pilot (indicating) Lamps capacitor single Phasing preventor,water level guard and laying and jointing the cables and twin earthing as per IE rules etc., Complete and testing the pump set and trail run for 10 days 2 HP Plat form All round (Twad Sor S no 17.3 pg.no 308) |
| 48 | Supply and run off 4 to 6 Sq.mm polythene insulator and PVC sheathed (Heavy Duty) service meter Aluminium cable of 1100 V grade on bearer wire for servive connection mains (SD 61).(320 Aluminim Wire)(SD WD-M1959) |
| 49 | Supply, delivery and fixing of the following ISI make water supply materials including all labour charges etc., complete |
| 50 | 2\\" dia Pipe clamp set (Twad sor WD-M0617) |
| 51 | 2\\" dia pvc bend (Sor M-0897) |
| 52 | 2\\" dia G.I Elbow (Sor M-0446) |
| 53 | 2\\" dia G.I Union (Sor M-0440) |
| 54 | 2\\" dia gate valve (Twad sor WD-M0618) |
| 55 | 2\\" U Pvc Pipe (Twad Sor WD-M0051) |
| 56 | 2\\" dia pvc pipe (Sor M-0879) |
| 57 | 2\\" dia pvc Tee (Sor M-0903) |
| 58 | 3/4\\" dia G.I Tee (Sor M-0462) |
| 59 | 3/4\\" dia G.I Elbow (Sor M-0450) |
| 60 | 3/4\\" dia Pvc Tap (Sor M-0510) |
| 61 | 3/4\\" dia GI Coupler (Sor M-0468) |
| 62 | saddle piece (Twad Sor WD-M0614) |
| 63 | Providing Construction of Brick work for HDPE tank with Pcc in 1:2:4 and Brick work CM:15 using II class ground moulded bricks of size 8 3/4 x 4/2 x 3/4 Earth Filling Plastering CM 1:5 20mm Thick painting etc Complete |
| 64 | Supply and fixing of 0.75 x 0.75 x 0.45 size made up with MS angle and plats of a kiosk erected on a masonary pedsal for protecting accessories etc., complete complying with standard specification.(Twad s no 18.0 pg no 89) |
| 65 | Providing painting and lettering over the PVC tank for the work details as per instrution given by the departmental officers etc., complete complying with standard specification. |
| 66 | Electrification charges |
| 67 | Supply and delivery of 25mm GI Pipe Service Pipe With Bend Including Coat and Coneyance etc,Complete as per Standard Specification as Directed by the Departmental Officers (Twad Sor WD-M0486) |
| 68 | Earth work excavation in all classes of soils and sub soils to full depth as may be required except hard rock requring blasting etc., complete (Sor W-0054) |
| 69 | Laying & Lowering of Pipe line extn complete as per the standard specification (Twad Sor WD-W0424) |
| 70 | Refilling with excavated sand complying with standardspecification for filling in foundation and basement (SOR W-0074) |
| 71 | Supply,delivery and fixing of Minimast (12 metre) with 6 Nos. 150W LED Fitting |
| 72 | Supplying and erecting in position of following literscapacity Industrial Model Reverse Osmosis Water-cum Purifier to deliver Potable Water with World HealthOrganisation (WHO) Standards with followingaccessories. (a) MS Skid- 1 No.(b) Media 11054 No. Vessel with 20 nb Multiport Valve(with Media Pubble and Fine Sand and ActivatedCarbon Filling) set(c) Feed Pump 0.50 HP 1 No. (d) Vertical Pump 2-9, 2.00 HP/Single Phase 1 No.(e) Membrane 40 x 40 filmtech (or) equilaents /Osmonic (USA)- 1 No. and Membrane Pressure Vessel40 x 40 -1 No. & Pressure Gauge - 2 Nos.(f) Flow Meter - 1 No. 20\\" Filter with Housing - 1 No.,Low Pressure Switch- 1 No., Level Switch - 1 No. &Necessary CPVC Pipes and Fittings.The system shall be provide with Two Panel ControlSystem with necessary Stainless Valves and Fittingsand Float Control etc. The rate should be inclusive of allcivil works, wherever necessary to install the System inposition and intact. ( 50Liters) |
| 73 | Providing construction of 10.00m dia and 5.50m dia up to 3.00 4 innter foundation with Reinforced cement concrete in 1:1 1.5:3 and side wall any brick main way work and inner side ceramic tiles size at 0.23x 0.23cm including fountain work plumpint work with all acceries , Electrical wires 5 HP & 3 HP motors and other , water supply accessieries etc., complete. |
| 74 | site cleaning using jcb hire charges.. Please Enable Macros to View BoQ information |
