|
| 1 | Excavation in soil in hilly area in all heights and depths in all kinds of soil including saturated soil comprising of mixed soil, ordinary rock and hard rock. All work of rock cutting by blasting shall be carried out by taking all necessary precautions against soil erosion, damages to hill side, water pollution etc. and to protect stability of hill side .Rock shall be excavated with chiseling and wedging out of rock (where blasting is prohibited). All earth work in cutting/excavation including rock excavation shall be carried out true to lines, grades, sides slopes, width, camber, super-elevation and level as shown on the drawing and as directed by the Engineer-in-Charge in conformity with the requirement of MoRD technical specification for Rural Road, Section. 300 & 1600 to achieve designed formation width including hauling and stacking of materials useful for construction at suitable sites safe manner and disposal of all surplus material to the approved dumping sites through all modes of transportation including head load and animal transport and mechanical means along with its leveling, fine dressing and carriage of machineries, tools, equipment’s and safety measures and other incidentals necessary to complete the work by mechanical means and labour if required. During the mobilization period, contractor should take the advanced x-section in 15 m (fifteen metre) interval of whole road length in the presence of Engineer-in-charge or his representative. In case the advanced x-sec has been taken in the presence of Engineer-in-Charge representative, in that case the same has to be got approved from Engineer-in-Charge. The land for dumping sites shall be arranged by the contractors himself and nothing extra shall be paid on this account, filling of unevenness blind age and finishing of the road to specified dimensions or as directed by the Engineer in-charge for smooth riding. The recovery for stones, whether useful or 65.16 (sixty five point one six ) cubic metre at the rate of Rs 300/-only (Rupees three hundred only ) per cubic metre shall be effected on prorata basis in all circumstances .Any loss to the public and private property during the course of excavation shall be the absolute responsibility of the contractor ,which shall have to be duly compensated by him in all cases. The rate is including octroi, royality, Malkana, toll tax, or any other taxes imposed by the Government but excluding GST. |
| 2 | Earth work in excavation for all type of road structure such as retaining walls, breast walls, culverts, drain and Parapets etcetra in all type of classification of soil comprising of ordinary soil, ordinary rock, hard rock chiseling /wedging out rocks (Where blasting is prohibited) as per drawings and M.O.R.D. technical specification section 300 and as per direction of the Engineer- in – Charge including setting out, Construction of shoring and bracing, removal of stumps and other deleterious materials and disposal of materials upto any lead and lift including dressing of sides, bottom and back filling in trenches with excavated suitable approved material to the original surface in layers not exceeding 150 mm (one hundred fifty milli metre) compacted thickness including shoring and strutting and pumping or bailing out water (surface and sub soil water ) upto any depth any quantam of water including cleaning of slush which may arise out during dewatering complete as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax, or any other taxes imposed by the Government but excluding GST. |
| 3 | Loosening of the ground upto a level of 300 mm (three hundred millimetres) below the subgrade level, watered, graded with motor grader and compacted in layers to meet requirement of Tables 300. 1 and 300. 2 of MORD with three wheel 80-100 (eighty to one hundred) kN static roller for subgrade construction as per MORD Technical Specification section 300. as per direction of Engineer-in-Charge. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 4 | Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with in all lifts and leads, transporting to site, spreading, grading by mechanical means to required slope and compacted with three wheel 80-100 (eighty to one hundred) kN static roller to meet requirement of Table 300. 2 complete as per MORD technical Specification section 300 & 1600 and as per direction of Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 5 | Construction of 1st (first) layer Bio enzyme (100 mm) (one hundred millimetre) based soil stablised layer (accredited by IRC) to a required thickness as per manufacturer design with local soil material/gravel/murram, having CBR greater than Equal to 5% (Five percent) and treating it with Bio Enzyme in the ratio 1L (one litre) for 12.5 cum (twelve point five cubic metre) soil , spreading in uniform layer with motor grader on prepared surface. mixing by mix in place method with rotavator at OMC and compacting with smooth wheel roller to achieve the desired density complete as per technical specification incl all labour, materials, like soil and metal, equipments etc., complete, including Supervision (Supervisor shall be provided by Bio Enzyme Vendor) as per the directions of the Engineer incharge of the work . Bio Enzyme Supervisor accomodation, food and local transport will be in scope of Contractor.The soil will have clay percentage by hydrometry between 8% to 30%, (eight percent to thirty percent) including carriage of material within all leads, lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST. |
| 6 | Construction of 2nd (second) layer Bio enzyme (100 mm) (one hundred millimetre) based soil stabilised layer (accredited by IRC) to a required thickness as per manufacturer design with local soil material/gravel/murram, having CBR greater than Equal to 6% (six percent) and treating it with Bio Enzyme in the ratio 1L (One litre) for 15.0 cum (fifteen point zero cubic metre) soil with 25% (twenty five percent) 40mm (forty millimetre) crusher broken metal(of compacted thickness) in desing mix, spreading in uniform layer with motor grader on prepared surface. mixing by mix in place method with rotavator at OMC and compacting with smooth wheel roller to achieve the desired density complete as per technical specification including all labour, materials, like soil and metal, equipments etc., complete, including Supervision (Supervisor shall be provided by Bio Enzyme Vendor) as per the directions of the Engineer incharge of the work . Bio Enzyme Supervisor accomodation, food and local transport will be in scope of Contractor. The soil will have clay % (percent) by hydrometry between 8% to 30% (eight percent to thirty percent) , including carriage of material within all leads, lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST. |
| 7 | Applying of curing material TerraCure after the application of Bio Enzyme layer (accredited by IRC) for by mixing TerraCure with water in the ratio of 1:200 (one isto two hundred) and then appyling the mixed solution @ 3 (at the rate three) litre for 1 sqm (one square metre) as per technical specifications and direction of Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST. |
| 8 | Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam 100 mm (one hundred millimetre) specification including premixing the material with water at OMC in mechanical mixer (Pug Mill), carriage of mixed material by tipper to site, laying in uniform layers in sub- base/base course on a well prepared sub-base and compacting with smooth wheel roller of 80 to 100kN (eighty to hundred kilonewton) weight to achieve the desired density including lighting, barricading and maintenance of diversion, etc as per MORD Technical Specification section 400 and direction of Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax, and any other taxes imposed by the Government but excluding GST. |
| 9 | Prime Coat Preparing and applying of water soluble organo silane Nano technology (for bitumen emulsion application, IRC accredited) with cationic bitumen emulsion CSSI and water <1000 (greater than one thousand) ppm TDS in the ratio of 1. 00 (One) kilogramme organo silane nanotechnology: 100 (One kilogramme) cationic bitumen emulsion CSS I. 00 (one):200 (two hundred) litre water Mixing & Spraying: Take 1. 00 (one) Kilogramme of organo silane nanotechnology and add in 200 (two hundred) litre water while filling water in tanker/drum and then add 100 (One hundred) cationic bitumen under circulation. Mix the solution completely. Spray the solution @1. 00 kg (one Kilogramme) per square metre on compacted surface. Rate including all materials labour hire charges of machinery etc. complete as per MoRD specifications clause 502 & direction of Engineer-in-Charge, including carriage of material with in all leads lifts and other incidental The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government excluding GST. |
| 10 | Tack Coat Preparing and applying of water soluble organo silane nanotechnology (for bitumen emulsion application IRC accredited with cationic bitumen CRSI and water<1000 (greater than one thousand)ppm TDS in ratio of 1. 00 (one) kilogramme organo silane:100 (one) killogramme cationic bitumen emulsion CRS I. 00: 200 One is to two hundred) litre water. Mixing & Spraying: Take 1. 40 (One point four zero) litre of organo silane nanotechnology and add in 200 (two hundred) litre water while filling water in tanker/ drum and then add 100. 00 (One hundred) litre cationic bitumen emulsion under circulation. Mix the solution completely. Spray the solution @ 0. 3-0. 4 (zero point three to zero point four) kilogramme per square metre on compacted base. Rate including all materials labour hire charges of machinery etcetera complete as per MoRD specifications clause 503 & direction of Engineer –in- Charge including carriage of material within all leads, lifts and other incidental. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government excluding GST. |
| 11 | Providing, laying and rolling of close-graded Mix Seal Surfacing surfacing material of 20 mm (twenty millimetre) thickness composed of 11.2 mm to 0.09 mm (eleven point two millimetre to zero point zero nine millimetre) (Type-A) @ 0.338 kg/per 10 sqm. (at the rate of zero point three three eight kilogram per ten square metre) aggregates using penetration grade bitumen @ (at the rate of) i e binders content @27.50 kg/10sqm (at the rate of twenty seven point five zero kilogram per ten square metre or 5.11% (five point one one percent) by weight and minimum density of MSS should be 2.10 gm/cc (two point one zero gram) to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 8-10kN (eight to ten kilonewton) static roller and finishing to required level and grades as per M.O.R.D. technical specifications section 500 including all leads, lifts and carriage of materials complete as per entire satisfaction of the Engineer in Charge. The rate is including octroi, royality, Malkana, toll tax or any other taxes imposed by the Government but excluding GST. |
| 12 | Construction of Granular Sub-Base (Grade-1) by providing well graded materials, spreading in uniform layers with tractor mount grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with three Wheel 80-100 kN (Eighty-hundred kilo newton) static roller to achieve the desired density, complete as per MORD Technical Specification section 400 for grading-I Material, as per the entire satisfaction and directions of Engineer-in-Charge including carriage of material within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 13 | Providing, laying, spreading and compacting by mechanical means of crushed stone aggregate size 53mm to 22.4mm ( fifty three millimetre to twenty two point four millimetre) Grading- III [75mm( seventy five millimetre) consolidated thickness] to water bound Macadam specification including spreading in uniform thickness using template, hand packing, rolling with three wheel 80-100 K.N. (eight to one hundred kilonewton) static roller in stages to proper grade and camber, including applying and brooming, stone screening type-B of size 11.2mm ( eleven point two milimetre) nominal size at the rate of 0.18cum (zero point one eight cubic metre) per ten square metres and to fill up the interstices of coarse aggregate, watering and compacting to the required density as per M.O.R.D. technical specifications section 400 and as per the entire satisfaction and direction of Engineer – in- Charge including carriage of materials within all leads, lifts and other incidental. The rate includes octroi, royality, Malkana, toll tax or other taxes imposed by the Government but excluding GST. |
| 14 | Construction of plastic cell filled cement concrete pavement, thickness as per design, over a prepared sub base, with 53 (fifty three) grade Ordinary Portland Cement (OPC) or any other type as per Clause 1501. 2. 4 M-30 (M- thirty) (Grade). Coarse and fine aggregates conforming to IS: 2386, maximum in a concrete mixer of not less than 0. 2 cum (zero point two cubic metre) capacity and appropriate weigh batcher using approved mix design (As per IRC 44-2088, laid in approved fixed side formwork (Steel channel, wedges, Steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed an plate vibrators and finished in continuous operation, Concrete should have a slump of 30-50mm (thirty to fifty millimetre) with use of approved plasticizer if required. Formwork of plastic cells should be made of High Density Polyethylene (HDPE), sheets having thickness ranging from 0. 20-0. 22mm (zero point two zero to zero point two millimetre) with sides 150mmx150mm (one hundred fifty millimetre into one hundred fifty millimetre) and height as fixed by Engineer-in-charge. Cells should be stitched using thread, thus ensuring optimum joint strength. Joint strength should be a minimum of 2 (two) Kilo Newton per metre. Heat welded cells should not be procured as they are not able to withstand the tension and often break when they are laid in the full width of the carriageway. Iron spikes of about 200MM (two hundred millimetres) long are to be used to keep the cell walls taut. Nylon thread or rope may be used to prevent collapse of cells during placement of concrete. Iron spikes to be taken out for use in other place as soon as the concrete is in place. The sub base should be provided with concrete/stone block or brick on edge on either side of the carriageway protecting the sub base with full thickness of the concrete pavement for its confinement and protection. Curing of concrete slabs for 14 (fourteen)- days, curing compound (where specified) and water finishing to lines and grade as per drawing and Technical Specification of cell filled Concrete Pavement Published by NRRDA and as per the entire satisfaction and direction of Engineer – in- Charge including carriage of materials within all leads, lifts and other incidental. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government excluding GST. |
| 15 | Providing and laying concrete mechanically mixed and vibrated PCC M-10 1:3:6 nominal mix (one cement: three sand: six graded crushed stone aggregate 20 (twenty millimetre) nominal size) for plain/reinforced concrete in open foundation and plinths or similar works complete as per drawings and MoRD technical specification section 800, 900, 1200 and 1600 and curing complete including the cost of form work and hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-charge. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 16 | Providing and laying concrete mechanically mixed and vibrated mix 1:4:8 (one cement: four sand: eight graded crushed stone aggregate 40mm (forty millimetre) nominal size) for plain/reinforced concrete in foundation and plinths or similar works complete as per drawings and MoRD technical specification section 800, 900, 1200 & 1600 and curing complete including the cost of form work and hauling of material in all leads and lifts as per the entire satisfaction and direction of Engineer-in-charge. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 17 | Providing and laying mechanically mixed and vibrated reinforced cement concrete in foundation, plinths and sub- structure using grade M-20 (M-Twenty) design mix with cement content not less than 350kg (three hundred fifty kilogram) per cubic metre with 20mm (Twenty millimetres) nominal size graded crushed stone aggregate as per drawings and MORD technical section 800, 900, 1200 and 1600 and curing complete including the cost of form work but excluding the cost of reinforcement for reinforced concrete work etcetera and curing complete including carriage of materials with in all kinds of leads, lifts and other incidental and as per the entire satisfaction and directions of Engineer-in-Charge. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 18 | Random rubble Stone masonry in cement mortar 1:5 ( one cement : Five sand) for substructure complete as per drawings and MORD technical specification section 700, 1200 and 1600, curing complete as per the direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidental. The rate is including octroi, Royality, Malkana, toll tax, or other taxes imposed by the Government but excluding GST. |
| 19 | Back filling with granular material behind abutments, wing walls, return walls and retaining walls complete as per drawing and MORD technical specifications section 1200, 1600 and as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 20 | Providing and laying 100mm (One Hundred millimetre) dia PVC pipe weep holes in brick masonry/stone masonry, plain reinforced concrete, Abutments, Wing walls, Return walls and retaining/breast walls extended through the full width of the structure with slope I (V):20 (H) (One vertical : Twenty Horizontal) towards draining face complete as per drawing and MORD technical specification section 700, 1200 and as per direction of Engineer-in-charge including carriage of materials within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government excluding GST. |
| 21 | Providing and laying of boulder apron laid in wire crates with 4 mm (four millimetre) dia GI wire conforming to IS: 280 and IS: 4826 in 100 mm x 100 mm (one hundred millimetre into one hundred millimetre) mesh (woven diagonally) including 10 % (ten percent) extra for laps and joints laid with stone boulders weighing not less than 40 kg (forty kilogram) each as per drawing and MORD technical specifications section 1300 including carriage of materials within all leads, lifts and other incidental. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 22 | Construction of hill side V-Shape drain of size 0. 45 x 0. 25 (zero point four five into zero point two five)metre with thickness of concrete 10cm (Ten centimetre) thick M-10 (M-Ten) grade drain in accordance with the requirement of specification true to line and grade, level and dimension and other particular as per drawing and technical specification clause 1606. 1 as per direction of Engineer-in-charge including cost of earth work in all kinds of soil and cost of form work with steel plates and carriage of materials within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government excluding GST. |
| 23 | Construction of unlined surface drains by manual/mechanical means of average cross-sectional area 0. 40 sqm (zero point four zero square metre) in all kinds of soil & ordinary rock to specified lines, grades, levels and dimensions. Excavated material to be used in embankment as per MORD Technical Specification Clause 307 and as directed by the Engineer-In-charge including carriage of material within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government excluding GST. |
| 24 | Providing and laying of parapets with mechanically mixed and vibrated cement concrete 1:4:8 (One cement :Four Sand :Eight graded crushed stone aggregate 40 mm (Forty millimetre) nominal size) curing complete including the cost of earth work in all kinds of soil and cost of form work with steel plates complete as per MORD technical specifications Section 300,800,900,1200 and 1600 as per direction of Engineer-in-Charge including carriage of material within all leads, lifts and other incidental.The rate is including octroi, royality, Malkana, toll tax, or any other taxes imposed by the Government excluding GST. |
| 25 | Providing and erecting W metal beam crash barrier comprising 3 mm (three millimetre) thick corrugated sheet metal beam rail 70 cm (seventy centimetre) above road/ground level fixed on ISMC series Channel vertical part of 150 mmx75 mmx 5 mm (one hundred fifty millimetre into seventy five milli metre into five millimetre) special 2.00 (two point zero zero) metre center to center 1.80 ( one point eight zero) metre high 1.10 (one point one zero) metre below ground road level all steel parts and filaments to be galvanized by hot dip process, a fitting to confirm to IS 1367 and IS-1364 metal beam rail to be fixed on the vertical post with a space of channel section 150 mmx75 mmx5 mm (one hundred fifty millimetre into seventy five milli metre into five millimetre) 330mm (three hundred thirty millimetre) long complete as per MORTH Specification section 800 including hauling of materials in all leads and lifts as per entire satisfaction and direction of Engineer-in- Charge.The rate is including octroi, royality, Malkana, toll tax or any other taxes imposed by the Government but excluding GST. |
| 26 | Providing and fixing Ordinary Kilometre Stone (Precast) Reinforced cement concrete M-15 (M-fifteen) grade of standard design as per IRC :8 fixing in position including painting and printing etcetera as per drawing and MORD technical specification section 1700 and as per the directions of the Engineer-in-Charge including carriage of material, within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 27 | Providing and fixing 5th (fifth) Kilometre stone (Precast) Reinforced cement concrete M-15 (M-fifteen) grade of standard design as per IRC :8 fixing in position including painting and printing etcetera as per drawing and MORD technical specification section 1700 and as per the directions of the Engineer-in-Charge including carriage of material, within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 28 | Providing and fixing 200m (two hundred metre) Stone (Precast) Reinforced cement concrete M-15 (M-fifteen) grade of standard design as per IRC :26 fixing in position including painting and printing etcetera as per drawing and MORD technical specification section 1700 and as per the directions of the Engineer-in-Charge including carriage of material, within all leads, lifts and other incidentals. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government but excluding GST. |
| 29 | Providing and fixing of typical PMGSY informatory sign board with logo as per M.O.R.D. specification and drawing . Three MS plates of 1.6 mm (one point six millimetre) thick top and middle plate duly welded with MS flat iron 25mmx5mm ( twenty five millimetres x five millimetres) size on back on edges. The lower plate will be welded with MS angle iron frame of 25mmx25mmx5mm (Twenty five millimetre x twenty five milimetres x five millimetre). The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 Nos. ( Two Nos.) 75mmx75mm (seventy five millimetre x seventy five millimetres) of 12 SWG (twelve standard wire gauge) sheet tubes posts duly embedded in cement concrete M-15 (M fifteen) nominal mix 1:2½ : 5 (One cement: Two and half sand: Five graded or crushed stone aggregate 40mm(Forty milimetres) grade blocks of 450mmx450mmx600mm ( four hundred fifty millimetres into four hundred fifty millimetres x six hundred millimetres), 600mm ( six hundred millimetres) below ground level. The top most diamond plate will be welded to middle plate by 47mmx47mm (Forty seven millimetre x forty seven millimetres) of 12 SWG (Twelve standard wire gauge) steel plate tube. All MS will be stove enamelled on both sides. Lettering and printing arrows, borders etcetera will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing and M.O.R.D. technical specifications section 1700 and Annexure 1700.1 as per direction of Engineer – in- Charge including carriage of materials within all leads, lifts and other incidental . The rate is including octroi, royality, Malkana, toll tax, or any other taxes imposed by the Government but excluding GST. |
| 30 | Providing and fixing \\"Citizen Information Boards\\" as per specifications and drawings Two MS Plates of 1.60mm (one point six millimetre) thick duly welded with MS angle iron frame 25mmx25mmx5mm(twenty five millimetre into twenty five millimetre into five millimetre) on edges supported with 2(two) Nos horizontal posts and vertical posts made of 75mmx75mm (seventy five millimetre into seventy five millimetre) of 12SWG (twelve standard wire gauge) Steel tube posts duly embedded in cement concrete M-15 (fifteen) nominal mix nominal mix 1: 2.5: 5 (One cement: Two and half sand: Five graded or crushed stone aggregate 40mm (Forty millimetres) grade blocks of 450mmx450mmx600mm ( four hundred fifty millimetres into four hundred fifty millimetres into six hundred millimetres), 600mm ( six hundred millimetres) below ground level. All MS will be stove enameled both side lettering and printing arrows border etc will be painted with ready synthetic enamel paint of superior quality in required shade and colour. All sections of posts and steel tube will be primer and two coats of epoxy paint as per drawing and MORD technical specifications Section 1700 and Annexure 1700.1 as per direction of Engineer-in-Charge including carriage of material within all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax, or any other taxes imposed by the Government excluding GST. |
| 31 | Providing and fixing of typical PMGSY 2.00 (two) Killometre board as per MORD technical specification section 1700 as per the directions of the Engineer-in-Charge including carriage of material, within all leads, lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax, or any other taxes imposed by the Government but excluding GST |
| 32 | Providing and fixing 900 (nine hundred) millimetres equilateral triangle of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting vide Clause 1701.2.3 fixed over aluminium sheeting, 1.5(one point five)millimetres thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm (seventy five into seventy five into six) millimetres vfirmly fixed to the ground by means of properly designed foundation with M-15 (fifteen) grade cement concrete 450 mm x 450 mm x 600 mm,( four hundred fifty into four hundred fifty into six hundred )millimetres 600 (six hundred )millimetres below ground level as per drawings and MORD Technical Specification section 1700 as per technical specifications & direction of Engineer-in-Charge including carriage of material within all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax, or any other taxes imposed by the Government but excluding GST |
| 33 | Providing and fixing 600(six millimetres) equilateral triangle) of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting fixed over aluminium sheeting, 1.5 mm (one point five millimetre) thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm (seventy five millimetre into seventy five millimetre into six millimetre) firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 450 mm x 450 mm x 600 mm( four hundred fifty millimetre into four hundred fifty millimetre into six hundred millimetre), 600 mm (six hundred )millimetres below ground level as per drawings and MORD Technical Specification section 1700 as per technical specifications & direction of Engineer-in-Charge including carriage of material within all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax, or any other taxes imposed by the Government but excluding GST |
| 34 | Providing and fixing 600 (six hundred) millimetres circular of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting fixed over aluminium sheeting, 1.5 (one point five) millimetres thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm (seventy five millimetre into seventy five millimetre into six millimetre) firmly fixed to the ground by means of properly designed foundation with M-15 (fifteen) grade cement concrete 450 mm x 450 mm x 600 mm( four hundred fifty millimetre into four hundred fifty millimetre into six hundred millimetre), 600 mm (six hundred )millimetres below ground level as per drawings and MORD Technical Specification section 1700 as per technical specifications & direction of Engineer-in-Charge including carriage of material within all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax, or any other taxes imposed by the Government but excluding GST |
| 35 | Providing and fixing 900 (nine hundred) millimetres size octagon of retro-reflectorised cautionary, mandatory and informatory sign as per IRC:67 made of encapsulated lens type reflective sheeting fixed over aluminium sheeting, 1.5 (one point five)millimetres thick supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm (seventy five millimetre into seventy five millimetre into six millimetre) firmly fixed to the ground by means of properly designed foundation with M-15 (fifteen) grade cement concrete 450 mm x 450 mm x 600 mm( four hundred fifty millimetre into four hundred fifty millimetre into six hundred millimetre), 600 mm (six hundred )millimetres below ground level as per drawings and MORD Technical Specification section 1700 as per technical specifications & direction of Engineer-in-Charge including carriage of material within all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax, or any other taxes imposed by the Government but excluding GST |
| 36 | Providing and erecting direction and place identifications of semi reflective sign boards as per IRC:67 made of 2 mm (two millimetre) thick M.S. Sheet duly stove enameled paint in white colour in front and grey colour on back with red reflective border of 70 mm (seventy millimetre) width and required message, letters, figures with reflective engineering grade tape as per MORD specifications of required shade and colour.Supported and welded on 47 mm x 47mm (forty seven into forty seven millimetre) of 12 (tweleve) SWG Square tube of 3050 mm (three thousand fifty millimetre) height duly strengthened by 25 mm x 5 mm (twenty five into five millimetre) M.S flat iron on edges on back firmly fixed to the ground by means of properly designed foundations with M-15 (M-ifteen) grade cement concrete 450 mm x 450 mm x 600 mm (four hundred fifty into four hundred fifty into six hundred millimetre), 600 mm (six hundred millimetre) below ground level as per approved drawing and Technical Specification Clause 1701. as per MoRD specifications. The rate are inclusive of Octroi , royality , malkana , toll tax , sale tax or other taxes imposed by the Government , but excluding GST and including entire carriage of material within all leads and lift as per entire satisfaction and direction of Engineer - in - Charge. |
| 37 | Providing and Fixing pavement marker (Cat eyes) made out of ABS 3 M (three) plastic of size 128x110x29.5 mm ( one hundred twenty eight into one hundred ten into twenty nine decimal five millimetre) without nail having 50mm ( fifty millimetres) stem of ABS The pavement marker shall be installed with epoxy ABS including carriage of materials and equipment with all mode of transportation and as per MORD specification section 1700 and as per direction of Engineer-in-charge including carriage of materials within all leads and lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax, or any other taxes imposed by the Government excluding GST. |
| 38 | Supplying and installation of delineators road way indicators, hazard markers, object markers with tape, 80-100 cm (eighty to one hundred centimetre) high above ground level, painted black and white in 15 (Fifteen) centi metres wide strips, fitted with 80 x 100 mm (eighty into one hundred millimetre) rectangular or 75 mm (seventy five millmetre) diametre circular reflectorised panels at the top, buried or pressed into the ground and conforming to IRC:79 as per MORTH Specifications clause 806 & direction of Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, or any other taxes imposed by the Government excluding GST. |
| 39 | Providing and laying of hot applied thermoplastic compound road marking paint 2.5mm (two decimal five millimetre) thick with refletorising glass beads as per IRC:35 at the rate 250 gram (two hundred fifty) gram per square metre area, thickness of 2.5mm (two decimal five millimetre) is exclusive of surface applied glass beads as per specificaiton and with strips of 0.10 (zero decimal one zero) metre width in centre lines or edge lines of the road as per MORTH specifications clause 803.4 and direction of the Engineer-in-Charge including carriage of material within all leads, lifts and other incidental. The rate is including octroi, Royality, Malkana, toll tax, or other taxes imposed by the Government but excluding GST. |
| 40 | Planting rooted slips of large stature grasses on slopes, including supplying clumps of appropriate grasses, splitting into slips, trimming roots, preparing lines, digging planting hole to a max of 5 cm (five centimetre) depth with metal rod or wooden peg depending on nature of soil, planting slips at the rate of three perdrill at the specing specified, and subsequent watering (if necessary). The rate are inclusive of Octroi , royality , malkana , toll tax , sale tax or other taxes imposed by the Government , but excluding GST and including entire carriage of material within all leads and lift as per entire satisfaction and direction of Engineer - in - Charge. |
| 41 | Providing and laying (to level or slope) 900mm dia (nine hundred millimetres) diametre reinforced cement concrete heavy duty non pressure pipes IS (Indian Standard) Class NP-3 (Non pressure- three) for culverts on first class bedding of Granular material in single row including providing and fixing collar with cement mortar 1 : 2 (One cement : two sand) but excluding the cost of excavation, protection works, back filling, concrete bedding and masonry work in head walls and parapets as per drawing and MORD technical specifications section 1100 and as per direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental. The rate is including Octroi, Royality, Malkana, Toll Tax or any other Taxes imposed by the Government excluding GST. |
| 42 | Providing and laying flooring with rubble stone in cement mortar 1:3 (one cement : three coarse sand) laid over cement concrete bedding complete as per drawing and technical specification section 1300 as per directions of Engineer-In-Charge including curing and carriage of material within all leads, lifts and other incidentals. The rate is including octroi, royality, Malkana, toll tax, or any other taxes imposed by the Government but excluding GST. Please Enable Macros to View BoQ information |
