|
| 1 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion : Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 2 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 3 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) |
| 4 | Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineerin-charge. Pre-laminated particle board with decorative lamination on both sides |
| 5 | Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete. with necessary screws etc complete as per direction of Engineer- in-charge. |
| 6 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 200x10 mm |
| 7 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Twin rubber stopper |
| 8 | Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. |
| 9 | Providing and fixing aluminium powder coated American handle of approved make and design, suitable for aluminium doors/windows, including all necessary screws, fittings and fixing complete in all respects, as per manufacturer’s specifications and direction of Engineer-in-Charge. |
| 10 | Providing and fixing aluminium door bottom sweep and perimeter door seal, made of extruded aluminium section with EPDM / neoprene / nylon brush sealing strip, fixed to aluminium door shutter and frame including cutting to size, drilling, screws, adhesive where required, complete in all respects, as per manufacturer’s specification and directions of Engineer-in-Charge. |
| 11 | Providing and fixing 8 mm dia Galvanized Iron (GI) tie rod for aluminium rolling or sliding shutters, including nuts, washers, brackets, and necessary fittings, cutting to required length, alignment, and making the shutter mechanism fully functional, complete as per manufacturer’s specifications and direction of Engineer-in-Charge. |
| 12 | Making opening of required standard size for providing aluminium glazed door in existing aluminium glazed partition by carefully dismantling/removing existing glass panels, particle board/infill panels, aluminium beading, sections, cleats, screws, fittings etc. without damaging the adjoining framework; cutting and modifying aluminium frame members as required; providing and fixing necessary additional aluminium sections to form proper jambs, head and sill members for door opening; refixing glass and particle board panels wherever required; making good the disturbed portions to match with existing work, complete in all respects, as directed by Engineer-in-Charge. |
| 13 | Providing and fixing decorative frosted/acid-etched effect self-adhesive polyester/PVC based film on existing aluminium glazed partitions and/or doors, of thickness as per manufacturer’s technical data sheet (film + adhesive thickness typically between 75 and 155 microns depending on pattern), with approved horizontal stripe pattern of specified width and spacing; having minimum 99% UV rejection, Class A fire rating (ASTM E84 or equivalent), permanent pressure-sensitive adhesive, and suitable for interior vertical glass applications; including thorough cleaning and preparation of glass surface, cutting to required size, proper alignment of stripes, wet application using suitable solution to prevent air bubbles/creases, neatly trimming edges, removing excess material, making good disturbed portions, and completing the work as per manufacturer’s specifications and as directed by the Engineer-in-Charge. |
| 14 | Note:-Rates should be quoted inclusive of all Taxes, GST @ 18% etc. Please Enable Macros to View BoQ information |
