|
| 1 | SITC of 3 MGD Capacity Non-Clog Sewage Submersible Pump at Haiderpuri SPS by carrying out the following mechanical works: Supply of non-clog sewage submersible pump for the duty parameters of Discharge 568 cubic meter, head 28 meter, working voltage 415 ± 10 %, 3 Phase, 50 Hz ± 5%, A/C Supply, F-Class insulation, having 1450-1500 RPM and 15-meter power & control cables with following accessories Lifting chain Lifting chain ring Lifting chain bow shackle LT Control Panelhaving standard switchgears, Motor protection relay, seal monitor relay, and Water level Controller Unit. The Panel should be as per manufacturers standard.MOC: Impeller: SS316, Casing: C.I.F.G. 260, Shaft: SS410, Solid Handling 100 mm,Make: BS/SU/KBL/Aqua/KSB/Kishor/Jasco |
| 2 | Supply C.I. double flanged non rising spindle 250 mm dia Sluice Valve, Pressure Class: PN 1.0. Make: - Kirloskar/ IVC/Jupitor |
| 3 | Supply of the 250 mm dia Non-Return Valve, Pressure Class: PN 1.0, Operation – Self. Make: - KBL/ IVC / JupitorSupply of 250 mm dia MS Pipe made out from 9.5 mm thick MS Sheet(Approximately 105 meter pipe shall be provided by DJB) 105 Meter |
| 4 | Supply of 10 mm thick MS Flange for 250 mm dia MS Pipe. Make: Tata/ Jindal |
| 5 | Supply of pre-fabricated250 mm dia bends made out from 10 mm thick MS Sheet, dully welded and having 10 mm thick flanges on both sides. Make: Tata/ Jindal |
| 6 | Supply of GalvanizedM.S. Nut bolts washer. |
| 7 | Rubber insertions for 250 mm dia pipe joints. Make: National / Jyoti |
| 8 | Painting of the complete MS Pipe with one coat of red oxide paint and two coats of black synthetic enamel paint. |
| 9 | Hire charge of mechanical excavator for excavation at site of work as per site requirement and refilling the same after completion of work, including diesel, mobile oil & lubricants etc as per site requirement. (DSR 2023: Item Code0020) |
| 10 | Fabrication & fitting of the delivery line from sump well to rising main tapping point using above supplied MS Pipe, Bend, Valves, N/B/W etc with the help of fitter, welder, cutter, helper, beldar, chowkidar, supervisor, and electrician, cutter set, oxygen cylinder, LPG cylinder, welding rod and other T & P required at site of work along with its transportation complete to be arranged at site of work by the firm. The job also includes Lowering of the Sewage Submersible Pump in the wet sump SPS with the help of Hydra and heavy-duty labour and connection of this delivery line in the header line |
| 11 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources: 6 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 12 | Fixing of the Control Panel on the location provided by the engineer in charge. The job also includes providing & fixing of MS stand for the control panel. |
| 13 | Supply of 3.5 C x 240sqmm AluminiumArmouredCable.Make:Grandlay/Gloster/Havells |
| 14 | Supply of 3 C x 50sqmm PVC Insulated Copper Cable Make:Grandlay/Gloster/ Havells |
| 15 | Supply of 3.5 C x 50sqmm PVC Insulated Copper Cable Make:Grandlay/Gloster/ Havells |
| 16 | Supply & installation of Junction Box, made out from SS Sheet, on the wet sump for connection of pumps cable to power cables from the Control Panel & Pump cables. |
| 17 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing masonry open duct as required.Above185 sq. mm and upto 400 sq. mm |
| 18 | Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required. Above 35sqmm and upto 95 sqmm (clamped with 25x3mm MS Flat Clamp) |
| 19 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3.5 C x 24 sqmm |
| 20 | Supply of 50 sq mm heavy duty copper thimbles. Make: Dowells / Kapson |
| 21 | Providing and fixing earth bus of 25 mm X 5 mm GI strip on surface for connections etc. as required. |
| 22 | Testing and commission of complete work in the Presence of Engineer-in-charge with full satisfaction Please Enable Macros to View BoQ information |
