|
| 1 | Earth work in excavation in foundation in ordinary soil ( loamy clay or sand ) i/c. lift upto 1.5 metre and lead upto 30 metre and i/c. back filling,watering and ramming of excavated earth into trenches and disposal of surplus earth as directed by Engineer-in-charge with cost of labour and T&P etc.required for proper completion of work. |
| 2 | Earth work in embankment / filling by power transported earth with a average lead 8.00 km. including excavation, loading,unloading, manual compaction, dressing and all lifts complete excluding royalty required for proper completion of work. |
| 3 | Providing & laying 80 mm. thick factory made C.C. Interlocking coloured tiles/paver block including 50mm thick compacted bed of fine sand proper embedding/laying of interlocking tiles leveling and dressing of surface to required level and slope,filling joints with fine sand and below it laying 0.10m. thick base concrete in 1:2:4 with cost of all materials,labour and T&P etc required for proper completion of work. directed by Engineer-in- charge. |
| 4 | Providing & laying of Cement Concrete in 1:3:6 (1 cement:3 coarse sand:6 stone grit 20-40 mm.size) including cost all materials ,labour and T&P etc. required for proper completion of work. |
| 5 | Providing & fixing Centering & Shuttering for C.C. Work i/c. rent of shuttering material ,labour and T&P etc. required for proper completion of work. |
| 6 | Steel Reinforcement for R.C.C. Work i/c. it's straightening, cutting, bending, binding and placing in position with cost of binding wire i/c cost of all materials, labour and T&P etc. required for proper completion of work. |
| 7 | Providing & fixing Centering & Shuttering for R.C.C. Work i/c. rent of shuttering material ,labour and T&P etc. required for proper completion of work. |
| 8 | R.C.C. M-20 Grade (1 Cement:1 .5 Coarse sand:3 Grit 12-20 mm.size) i/c. cost of all materials, labour and T&P etc. but excluding cost of reinforcement required for proper completion of work. |
| 9 | Providing and laying autoclaved aerated cement blocks masonry with 150mm/ 230mm /300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately) |
| 10 | Brick work in 1:4(1cement:4coarse sand) cement coarse sand mortar including cost of all materials,labour and T&P etc. required for proper completion of work. |
| 11 | Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron 'Y' shaped placed 2.4m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ metre |
| 12 | 12.50mm thick cement plaster in 1:4 (1Cement:4Coarse sand) cement mortar i/c. cost of all materials, labour, and T&P etc . Required for proper completion of work. |
| 13 | Providing Cow dung manure including cost of all material, labour, T & P, all lead & lift for proper completion of work : Per Cum. |
| 14 | Spreading of Cow dung manure , Gypsum and fertile soil in the required thickness as Directed by Engineer in Charge including all cost of labour, T & P, all lead & lift fpr proper completion of work. |
| 15 | Mixing Cow dung manure and earth in the required proportion as specified or directed by Engineer in Charge including cost of all labour, T & P all lead & lift for proper completion of work. |
| 16 | Providing and laying of selection no 1 grass turf with earth on 50 mm to 60 mm in thickness including warering and maintenance of the lawn for 60 days or more till the grass forms a thick lawn, free from weeds and fit for moving including cost of all materials,labour T & P all lead and lift for proper completion of work. |
| 17 | Construction of Over Head Tank (100KL) with 20 metre staging including bearing capacity of soil test, Design, Drawing, etc complete as per the direction of Engineer incharge. |
| 18 | Providing and fixing of Gates including of all materials, labour, T&P all lead and lift required of proper completion of work. Total weight of 1 no. Gate 805kg. Including primer paint. |
| 19 | Providing and fixing 25 mm thick shutters for cup board etc. :Panelled or panelled & glazed shutters : Second class teak wood including ISI marked anodised aluminium butt hinges with necessary screws |
| 20 | Providing and fixing ISI marked flush door shutters conforming to IS :2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply venee ring with vertical grains or cross bands and face veneers on bothfaces of shutters: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 21 | Supplying and fixing of 3mt. Height Pole light with single lamp i/c cost of installation, all material, labour/ electrician with 15.00 meter long two core 1.5 sqmm cable and 0.40 X 0.40 X 0.50 m CC 1:2:4 in foundation block i/c T&P etc all complete. As per ISI marks or approved by Engineer-in-charge. |
| 22 | Supplying and fixing of 3mt. Height Pole light with double lamp i/c cost of instalation, all material, labour / electrician with 15.00 meter long two core 1.5 sqmm cable and 0.40 X 0.40 X 0.50 m CC 1:2:4 in foundation block i/c t&p etc all complete. As per ISI marks or approved by Engineer-in-charge. |
| 23 | Providing and fixing factory made solid Foam uPVC profile for kitchen cabinet frame (45 x 20 mm) of approved shade, quality and make. The profile shall be laminated on both sides, made from rigid foam sheets (Single extruded) having density 600 Kg/cum and the exposed edges sealed with PVC edge beading of same shade and colour. The frame shall be fire retardent with necessary screw holding capacity. Frame shall be fixed to wall using Expendable Fastner with necesary stainless steel screws, all complete as per direction of Engineer-in-charge. |
| 24 | Providing and fixing factory made Kitchen Cabinet Shutter/Partition 20 mm nominal thickness of approved shade, quality and make, made from rigid foam sheets (Single extruded) having density 600 Kg/cum and laminated on both side by laminate Sheet/PVC foil lamination. The exposed edges shall be sealed with PVC edge beading of same shade and colour. The shutter shall be fire retardenthaving necessary screw holding capacity. Shutter shall be fixed to frame using approved hinges with necessary stainless steel screws, all complete as per direction of Engineer-in-charge. |
| 25 | Providing and fixing wire gauge shutters using S.S. 304 wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.50 mm, for doors, windows and clerestory windows with hinges and necessary screws . |
| 26 | Supply and fixing of Bollard made (Single side) out of 2mm thick alluminium sheet face to be covered with high intensity prismatic grade type IV sheting , legends , letters , numerals and borders etc should be as per MoRTH specification no. 801.3.7 . Welded poly shaped to make monolithic piller size 1200mm high bollard is having a frame 900x600mm and 600 mm dia for fixation made out of 35x35x5mm angle iron and from side is fully cover. (Size of foundation 0.45x0.45x0.60m). As per ISI marks or approved by Engineer-in-charge. |
| 27 | Supplying and laying of 25 Sqmm 5/4 core Cable aluminum conductor PVC insulated armored sheathed cable 1100 volts grout with M.S. clamps of suitable size as directed by Engineer-in-charge, complete in all respect. Armoring shall be properly connected by clamps (Four underground laying cable shall be placed at a depth of 750 mm below ground level over a cushion of 75 m thick and all around and protected with bricks on sides and top). As per ISI marks or approved by Engineer-in-charge. |
| 28 | Supplying and fixing of High Mast Lights including cost of high mast shaft, construction of foundation, outdoor stand mounted feeder piller with 32 A TPN MCb incomer,single dial time switch 45 A TP contractor 240 Watt dia-cast Aluminium IP 65 flood light with high power LED fixture Havells and civil foundation M-20 Grade with material and installation,testing, commisioning with complete lights wiring work. feeder pillerproviding with 2 np GI pipe earthing works including all complete. As per ISI marks or approved by Engineer-in-charge. |
| 29 | Supplying and laying of PVC insualeted and PVC sheated/ XLPE power cable of 1.1 KV grade of up to 35 mm size direct in ground including excavation ,sand cuisioning, ptotective covering and refilling the trench etc as required required for completion of work. |
| 30 | Finishing wall with weather coat by primium acrylic exterion paint applied @1.67letre per 10sqm. (Asian or berger brand) of approved mack and quality on wall with two or more coat to give an even shade including a priming coat with cement primer of approved brand and manufacturer exterior primer applied @ 2.20kg /10sqm. after throughly brushing the surface free from mortar dropping and other foreign matters and sand papered smooth including supply all materials, labour, T & P etc required for proper completion of work. |
| 31 | Painting or Varnishing work in small area on new wood works with one coat upto one sqm. Metre of ready mix priming paint and one coat of approved superior qualuty ready mix paint or varnish including supply of all materials, labour, T&P etc required for proper completion of work. Paint to be used should confirming the ISI no. 103-109. |
| 32 | Boring/drilling bore well of 300mm dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level in all types of soil. |
| 33 | Boring/drilling bore well of 300mm dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level in Rocky strata including Boulders |
| 34 | Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric Resistance Welded) FE 410 mild steel screwed and socketed/plain ended casing pipes of 200mm dia, conforming to IS: 4270, of reputed & approved make, including painted with outside surface with two coats of anticorrosive paint of approved brand and manufacture, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of Engineer-in-charge. |
| 35 | Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge. |
| 36 | Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of useable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by “V” notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, including disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge. |
| 37 | Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell . |
| 38 | Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. |
| 39 | Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I). |
| 40 | Providing and fixing open well submersible pumps mono block, 3 Phase 440 volts/50 cycles per second with water cooled induction motor SS 410 shaft, SS Body, SS impeller and mechanical seal, pumps are provided in the set of two pumps(one working + one standby), pumps shall be complete with motor control panel fabricated from 14 SWG MS sheet comprising of incomer MCB, copper bus bar, phase indication lights, multifuntional meter(for indicating current between phases, votage between phases, Hz meter), outgoing MCB one for each motor, single phase preventors one for each motor, Auto manual switch one for each motor, all internal wiring, DOL starter one for each motor, wiring/cabling from motor to panel, earthing wire from panel to motor. Pumps shall also comrising of gate valve on delivery, NRV on delivery, pressure gauge on delivery and complete as per following details:(For water transfer pumps) Capacity=100 lpm, Head=25mtr. |
| 41 | Supplying & installation of 80mm dia column pipe made out of 80mm dia GI including the cost of fittings complete in all respect Jindal, Hissar/Prakash make \\"B\\" Class pipe. |
| 42 | Providing and fixing Gun Metal gate valve with C.I. wheel of approved quality (screwed end) 50 mm. Dia. Nominal bore including cost of all materials, labour and T&P etc. required for proper completion of Work. |
| 43 | Providing and fixing Gun Metal gate valve with C.I. wheel of approved quality (screwed end) 65 mm. Dia. Nominal bore including cost of all materials, labour and T&P etc. required for proper completion of Work. |
| 44 | Providing and fixing Gun Metal gate valve with C.I. wheel of approved quality (screwed end) 80m. Dia. Nominal bore including cost of all materials, labour and T&P etc. required for proper completion of Work. |
| 45 | Sal wood work in chaukhat frame with M.S. hold fast i/c. cost of all materials,labour and T&P etc. required for proper completion of work. |
| 46 | Supply and fixing of 4.5 cm. thick C.P. teak wood glazed shutter in window including all necessary fittings with cost of all materials ,labour and T&P etc. required for proper completion of work. |
| 47 | Providing & fixing M.S. or iron work of small and section such as M.S. grills & railling etc.including rivetting or welding where necessary with cost of all materials,labour and T&P etc. required for proper completion of work. |
| 48 | Providing and fixing wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws etc. required for proper completion of work. |
| 49 | Painting two coat over primming coat on steel and other metal surface including cleaning the surface of all dirt,dust and other foreign matter,sand papering and stopping i/c. cost of all materials, labour,T&P etc. required for proper completion of work. |
| 50 | Wiring for light plug point with 3x2.5 sq mm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) along with modular type 6 Amp switch and 3 pin 6 amps socket outlet with modular base and cover plate, suitable size G.I. box, earthing the switch box and socket outlet with same size wire etc. as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5)-Medium Point etc. required for proper completion of work. |
| 51 | Wiring for power plug point with 3x4 sq mm FRLS PVC insulated stranded copper conductor wire for phase, neutral and earth in concealed FRLS PVC conduit (heavy duty, thickness of pipe should be 2 mm) along with modular type 16 Amp switch and 6 pin 16 amps socket outlet with modular base and cover plate, suitable size G.I. box, earthing the switch box and socket outlet with same size wire etc. as per specification and IS: 694 (2010), IS: 9537 (2000 Part 5)- Medium Point etc. required for proper completion of work. |
| 52 | Supplying & fixing DP sheet steel enclosure on surface/recess along with 25/32 A 240 V \\"C\\" Curve DP MCB complete with connections, testing and commissioning etc. required for proper completion of work. |
| 53 | Providing & fixing white vitereous china pedestal type water closet ueropean W.C. Pan with seat and lid, 10 letre low level white PVC flushing cistern including flush pipe with manualy controlled device (handle lever) conforming to IS : 7231, with all fitting and fixtures including cutting and making good the wall and floors wherever required . W. C. pan with IS marked white solide plastic seat and lid. etc. required for proper completion of work. |
| 54 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap etc. required for proper completion of work. |
| 55 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 40 mm dia etc. required for proper completion of work. |
| 56 | Providing and fixing 100 mm sand cast Iron grating for gully trap. etc. required for proper completion of work. |
| 57 | Providing and fixing soil, waste and vent pipes : 100 mm dia Sand cast iron S&S pipe as per IS: 1729 etc. required for proper completion of work. |
| 58 | Providing and fixing uplasticised PVC connection pipe with brass unions including cost of all materials,labour and T&P etc. required for proper completion of work. |
| 59 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank etc. required for proper completion of work. |
| 60 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. etc. required for proper completion of work. |
| 61 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 etc. required for proper completion of work. |
| 62 | Providing and fixing C.P. brass angle valve for Wash basin mixer and geyser points of approved quality conforming to IS:8931 |
| 63 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. |
| 64 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 15 mm nominal bore |
| 65 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) 15 mm nominal dia Pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. |
| 66 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) 20 mm nominal dia Pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. |
| 67 | Providing and laying water proofing treatment on roof of slabs by applying cement slurry mixed with water proofing cement compound consisting of applying after surface preparation,first layer of slurry of cement @0.488 kg/sqm. mixed with water proofing compound @0.253kg/sqm.and then laying second layer of fibre glass cloth when the first layer is still green, Overlaps of joints of fibre cloth shoud not be less than 10mm. after it applying third layer of 1.5mm. thick of cement slurry @1.289 kg/sqm. mixed with water proofing compound @0.670 kg./sqm. and coarse sand @1.289 kg./sqm. including cost of all materials ,labour and T&P etc. required for proper completion of work. labour. |
| 68 | Providing and fixing RETRO REFLECTIVE SIGN BOARDRetro reflective sign Board fully Retro reflective sign board made out of 2mm thick ACP sheet corrosion resistant sheet face to be fully covered with high intensity Retro Reflective Diamond Grade (3M) type-9 encapsulated lens type weather resistant show colour fastness in green colour. The retro reflective sheet shall be processed on base aluminium by pressure sensitive adhesive of the aggresive track type requiring no heat as per manufacture specification, Machine signs, Letters and symbols shall be cut by commputerised cutting machine and fabicrated out of Retro reflective sheeting Diamond grade 3M Board are to be supplied along with back supported Iron frame of 32x32x3mm back side of the board shall be painted with slove enamel paint.SIZE: 1.22Mtr. x 5 Mtr. |
| 69 | Providing and fixing RETRO REFLECTIVE SIGN BOARDRetro reflective sign Board are made of 2mm thick ACP sheet to be fully covered with enginurs grade Retro reflective as per colour required by I/O. The Retro reflective sheet shall be processed on base aluminium as per reccommendation Text and sign. Text and sign symbols will be computerized and fabricated on N. T. grade. The sheet with lives of extra frame of angle iron 32x32x3 mm duly painted. one a two posts of M.S. heavy duty channel of 75x35x35 3000mm long and painted super synthetic enamel paint. SIZE: 4' x 3' |
| 70 | Providing and fixing RETRO REFLECTIVE SIGN BOARDRetro reflective sign Board are made of 2mm thick ACP sheet to be fully covered with enginurs grade Retro reflective as per colour required by I/O. The Retro reflective sheet shall be processed on base aluminium as per reccommendation Text and sign. Text and sign symbols will be computerized and fabricated on N. T. grade. The sheet with lives of extra frame of angle iron 32x32x3 mm duly painted. one a two posts of M.S. heavy duty channel of 75x35x35 3000mm long and painted super synthetic enamel paint. SIZE: 5' x 4' Please Enable Macros to View BoQ information |
