|
| 1 | Earth Work excavation in foundation trenches in hard soil vide classification of soil item B and disposal of excavated earth as obtained to a distance up to 50 M all complete as per approved design building specification and direction of E/I. |
| 2 | Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/I.[Mode of measurement compacted volume] |
| 3 | Providing designation 75B one brick flat soling, joints filled with local sand including cost of watering taxes, royalty all complete as per as per drawing, specification & direction of E/I. |
| 4 | Providing P.C.C. M-150 With nominal mix of concrete (1:2:4) in foundation all complete job as per specification and direction of E/I. |
| 5 | Providing R.C.C. M-200 with nominal mix of [1:1.5:3] in foundation and plinth with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M. 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing [but excluding the cost of reinforcement] taxes and royalty all complete as per building specification and direction of E/I. |
| 6 | Providing R.C.C. M-200 with nominal mix of [1:1.5:3] in columns with approved quality of stone chips 20mm to 6mm size grade and clean coarse sand of F.M. 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing [but excluding the cost of reinforcement] taxes and royalty all complete, as per building specification and direction of E/I. |
| 7 | Providing designation 75B brick work in C.M.(1:6) in foundation and plinth all complete as per building specification and direction of Engineer-in-charge |
| 8 | Providing designation 75B brickwork in C.M.[1:6] in Superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening, scaffolding, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I. |
| 9 | Providing 25mm thick damp proof course with cement concrete M-200 with nominal mix of [1:1.5:3] with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M. 2.5 to 3 including screening, shuttering, and mixing cement concrete in mixer with 5%cico or any other approved water proofing compound and placing in position, striking, curing, taxes and royalty all complete, as per building specification and direction of E/I. |
| 10 | Providing R.C.C. M-200with nominal mix of [1:1.5:3] in beam, Chajja, of all types with approved quality of stone chips 20mm to 6mm size graded and clean coarse sand of F.M. 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing [but excluding the cost of reinforcement] taxes and royalty all complete, as per building specification and direction of E/I. |
| 11 | Providing precast R.C C.M-150 with nominai mix of (1:2:4) slab of desired size all complete as per building specification rnd direction of E/I |
| 12 | Columns footings |
| 13 | COLUMNS in S/S |
| 14 | TIE BEAM |
| 15 | ROOF SLAB |
| 16 | Centering and shuttering including strutting, propping etc and removal of form for staircase. |
| 17 | Providing T.M.T Steel reinforcement for R.C.C. work with cutting bending fixing in work place as per design drawing grade of steel Fe-500 (only valid fro Sail, Tata ,Jspl, Electro Steel Ltd. And Vizal Steel)-do-all complete job as per specification and direction of E/I. |
| 18 | Filling in foundation trenches and plinth in layers not exceeding 150mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50M and lift of lift of 1.5M all complete as per building specification and direction of E/I. [Mode of measurement compacted volume] |
| 19 | Providing 12mm cement plaster [1:6] with clean coarse sand of F.M. 1.5 including cost of screening curing with all leads & lifts of water scaffolding, taxes & royalty all complete as per building specification & direction of E/I. |
| 20 | Providing 6mm cement plaster [1:4] in ceiling with clean coarse sand of F.M. 1.5 including cost of screening curing with all leads & lifts of water scaffolding, taxes & royalty all complete as per building specification & direction of E/I. |
| 21 | Providing and laying double charge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make,complete Size of Tile 600x600 mm. |
| 22 | Supplying, fitting and fixing M.S. grill made of 20*6mm M.S. flat as per approved design & drawing, properly fabricated with joints continuous fillet welded & finished smooth, carriage of grill to work site, hoisting as per building specification & direction of E/I. as per building specification & direction of E/I. |
| 23 | Providing and fixing almunium work for doors, windows, ventilators and partitions |
| 24 | For shutter of doors, windows, ventilators including |
| 25 | Providing and fixing glazing in aluminium doors, windows, ventilators and partitions |
| 26 | Providing and fixing pressed steel door frames conforming to IS:4351 |
| 27 | Supplying fitting and fixing 250x20x6mm L type M S clamp properly fishtailed |
| 28 | S/F/F 35mm thick solid core type non decorative single leaf flush door shutter-do-do-E/I. |
| 29 | S/F/F Collapsible Gate all complete job….E/I |
| 30 | Providing 24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section complete as per manufacturer's specification and direction of Engineer-in-charge. (For W.C. and bathroom door shutter) |
| 31 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) of size 580x440 mm with integral type foot rests. |
| 32 | Providing and fixing wash basin with C.I. brackets, 15 mm PTMT pillar cock, 32 mm PTMT waste coupling of standard pattern. |
| 33 | Providing Two coats of ready mixed paint over a coat of primer one coat of red lead paint approved make over a new steel surface -do-all complete job as per specification and direction of E/I. |
| 34 | Providing two coats of white cement putty of approved shade and make over a coat of cement primer over new surface including preparing plastered surface -do-all complete job as per specification and direction of E/I. |
| 35 | Providing two coats of plastic emulsion paint of approved shade and make over a coat of cement primer over new surface including preparing plastered surface by rubbing smooth with pumica stone or fine sand paper applying putty wherever required -do-all complete job as per specification and direction of E/I. |
| 36 | Providing two coats of snowcem of approved shade & make over a coat of cement primer on new surface including preparing the plastered surface by rubbing smooth with fine sand paper, scaffolding, curing & taxes all complete as per building specification & direction of E/I. |
| 37 | Providing and fixing on wall face unplasticized- PVC rigid PVC rain water pipes conforming to IS:13592 type A including jointing with seal ring conforming to IS: 5382, leaving 10 mm gap for thermal expansion |
| 38 | Providing and fixing on wall face unplasticized- PVC moulded fittings/ accessories for unplasticized- PVC rigid PVC rain water pipes conforming to IS:13592 type A including jointing with seal ring conforming to IS: 5382, leaving 10 mm gap for thermal expansion Coupler 110mm |
| 39 | Bend 87.5 110mm |
| 40 | Shoe 110mm |
| 41 | PVC pipe clips |
| 42 | Providing and placing on terrace (at all floor levels) polyethylene water store tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 43 | Providing and fixing PTMT bib cock of approved quality and colour.15 mm nominal bore, 122mm long, weighing not less than 99 gms. |
| 44 | Cement + Steel Lead 5 KM |
| 45 | Sand Lead 30 KM |
| 46 | Stone Chips Lead 10 KM |
| 47 | Brick Lead 30 KM |
| 48 | Wiring for light point/ fan point/exhaust fan point / call bell point with 1.5 sq.mm FR PVC Modular type GROUP - B |
| 49 | Wiring for Twin control light point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, with 2way modular switch ,modular plate, suitable GI box and earthing the point with 1.5sq mm FR PVC insulated copper conductor single core cable etc as required. |
| 50 | Wiring for light/power plug with 2x 4 sq.mm FR PVC insulated, copper conductor |
| 51 | Circuit/submain wiring in PVC conduit - 2X1.5 sq mm +1 x 1.5sq mm earth wire |
| 52 | Circuit/submain wiring in PVC conduit - 2X2.5 sq mm +1 x 2.5sq mm earth wire |
| 53 | 2X10 sq mm + 1X 10 sq mm earth wire. |
| 54 | Supplying and fixing suitable size GI box with moduler plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps moduler socket outlet and 5/6 amps moduler switch , connection painting etc.as reqd. |
| 55 | Supplying and fixing suitable size GI box with moduler plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps moduler socket outlet and 15/16 amps moduler switch , connection painting etc.as reqd. |
| 56 | Supplying and fixing 20amp 240v SPN industrial type socket outlet , with 2 pole and earth metal enclosed plug top alongwith 20amps, G- series, SP MCB ,in sheet steel enclosure , on surface or in recess, with chained metal cover for the socket , outlet , and complete with connections , testing and commissioning etc . as requried . |
| 57 | S/F of following sizes of PVC conduit alongwith the accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required .20 mm PVC coduit. |
| 58 | 25 mm PVC coduit. |
| 59 | Suppling and fixing following moduler type switch / socket on the existing switch box / cover including connection etc. as reqd.5/6 amps switch |
| 60 | 5/6 amps socket |
| 61 | 1 or 2 module moduler boxes,base & cover plate. |
| 62 | S/F Moduler type electronic fan regulator. |
| 63 | S/F moduler type blanking plate. |
| 64 | Supplying and fixing of following way single pole & neutral, sheet steel , MCB distribution board 240 volts, on surface /recess , complete with tinned copper bushbars, neutral busbar, earth bar, din bar, detachable gland plate, interconnections ,phosphatized and powder painted including earthing etc. as requried. (but without MCB/RCCB/ISOLATOR) 2+12 way |
| 65 | Supplying and fixing 5 amps to 32 amps, rating, 240 volts, 'B' series - 6/32amp Single pole |
| 66 | Earthing with copper earth plate 600*600*3 mm thick including accessories and providing masonary inclosure with cover plate having locking arrangement and watering pipe etc. with charcoal and salt as reqd. |
| 67 | Suppying & laying 8 SWG copper wire at 0.50 mtr below ground level for conductor earth electode including soldering etc .as reqd. |
| 68 | Providing & fixing of 300MM exhaust fan. |
| 69 | SITC of 1200mm (48\\") BLDC 5 star rating 32 W Ceiling fan conforming to IS:374:2019 suitable for 230 V50Hz single phase supply etc complete as required. |
| 70 | SITC of 20/22 W LED tubelight fitting suitable for 230 V50Hz single phase supply etc complete as required. |
| 71 | P & F of 30w LED street light |
| 72 | 15/16 watt LED Bulb |
| 73 | Cost of drilling 200mm x 165mm x 230meter deep bore well in all kinds of soil and rock in rural or any other area for installation of pump set with Hydraulic DTH Rig machine, all complete including supplying all materials, tools drilling rig and Air Compressor and equipments, as well as fuel, lubricants and cost of transportation of Rig machine and other vehicles up to the site including cost of flushing charges, Geological investigation etc. all complete.(Sl. No. 119)(i) From 0 – 50 meter |
| 74 | (ii) From 51 – 230 meter onwards |
| 75 | Supplying all tools, equipment, labours and doing washing, flushing and development of drillled tube well to give clean and clear water all complete as per direction E/I. (Sl. No. 126) |
| 76 | Supply of 200 mm dia x 3.00 m long UPVC casing pipe conferming to IS:12818:2016 (CML No. 5543459) latest revision including carriage. (Basic rate ) (Sl. No. 129) |
| 77 | Supplying all tools, equipment, labours and lowering 32 mm dia G.I suspension pipe in 3mtrs length in the drilling bore of T/W etc. all complete job as direction of E/I. (Sl. No. 132) |
| 78 | Providing labours for fitting and fixing deep well cylinder jointing materials, chrome leather bucket all tools and plant etc .required for the job for low water level all complete job as per specification and direction of E/I.(Sl. No. 133) |
| 79 | Cost of 32mm dia. G.I. Medium quality pipe 3Mtrs long screwed at both ends with seamless socket as per IS: 1239 (part-1 to 8)/2004 with latest amendment Including all taxes, royalty and contractor profit etc. (SOR Sl. No. 109) |
| 80 | Supplying submersible pump sets conforming to IS 8034 and motor conforming to IS 9283. Pump shall be suitable for various delivery head and discharge with stainless steel pumpshaft and polypropylene impeller. Motor suitable for working on 415V(+-)10% ,3PH, 50Hz, A.C supply with cable guard, thrust carbon/ fiber bearing to withstand entire hydraulic thrust water proof winding shall be provided. (SOR Sl. No. 139)Submersible pump 150 mm dia 2.0 HP |
| 81 | DOL starter with SS Enclosure with 380/415 volt coil as per IS 3914 (5 HP) |
| 82 | FR PVC insulated 3 core 4sqmm Copper wire |
| 83 | GST @ 18% |
| 84 | Labour Cess 1% Please Enable Macros to View BoQ information |
