|
| 1 | Surface Dressing of the ground in any kind of soil including removing vegetation inequalities not exceeding 15 cm depth and disposal of the rubbish within a lead upto 75 m as directed. |
| 2 | Earth work in filling in compound, tank, low land, ditches etc. with good earth, in layers not exceeding 150 mm. including breaking clods and consolidating the same by ramming and dressing complete.(Payment will be made on profile measurement before and after the work)With carried earth arranged by the contractor within a radius exceeding 5 km. but not exceeding 10 km. including cost of carried earth. |
| 3 | Supplying and fixing grasses tiles of grass Maxican Carpet/Selection No. 1 Healthy & fresh grasses (size 1'x1' or bigger) including watering and maintenance of the lawn for 30 days or more till the grass forms a thick lawn free from wees and fit for mowing including supplying good earth as required by Engineer-in-charge. (Rate includes supply of labour, tools & plants including materials) |
| 4 | Single Brick Flat Soling of picked jhama bricks including ramming and dressing bed to proper level and filling joints with local sand. |
| 5 | Brick work with 1st class bricks in cement mortar (1:6).In foundation and plinth |
| 6 | 125 mm. thick brick work with 1st class bricks in cement mortar (1:4) in ground floor. |
| 7 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor). [Excluding cost of chipping over concrete surface]With 1:6 cement mortar : 20 mm thick plaster |
| 8 | Ordinary Cement concrete (mix 1:1.5:3) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant IS codes.Pakur Variety |
| 9 | Supplying & laying as per IRC-SP:063-2004 paver unit of any shade of approved quality as per relevant IS code, laid in pattern as directed in pavement, footpath, driveway (paver block only), etc including necessary underlay complete in all respect with all labour and material.[Border concrete if necessary to be paid separately].Note: Sub-grade CBR should not be less than 5.60 mm thick interlocking designer concrete paver block M 35 grade for light-traffic zone,commercial & office complex,tourist resort as per IS: 15658-2006 (over 20-40 mm medium sand bed on 250mm thk WBM/ WMM base course & 250 mm thk bound gnaular /granular sub-base course including cost of sand for sand bed but excluding cost of base ,sub-base course & subgrade preparation.)Coloured Decorative |
| 10 | M.S. structural works in roof trusses with tubular sections conforming to IS: 806-1968 & IS: 1161- 1998 cnnected to one another with bracket, gusset cleats as per design, direction of Engineer-in-charge complete including cutting to requisite size, fabrication with necessary metal arc welding conforming to IS: 816-1969 & IS: 9595 using electrodes of approved make and brand conforming to IS:814- 2004, haulage, hoisting and erection all complete.The rate includes the cost of rolled steel section, consumables such as electrodes, gas and hire charge of all tools and plants and labour reqired for the work including all incidental chages such as electricity charges, labour insurance charges etc. Payment to be made on the basis of calculated weight of structural tubular memebrs as specified in relevent IS code in finished work. Payment for gusset, bracket, cleat may be made by adding the actual weight of such items with weight of finished structural members. The rates are considered for a height of erection 8 m. / 2nd floor level from the ground. Add 1.5 % extra over the rate for each additional floor or 4m. beyond the initial 8 m. or part thereof.For trusses spanning up to 12.00 m |
| 11 | Supplying, fitting, fixing, Chain link fencing of approved quality with R.C.C posts wooden posts or iron posts by means of galvanised \\"C\\" clips to grid of horizontal strands of galvanised high tensile spring steel wire of 12 S.W.G which have to betensioned and fixed to the vertical posts by means of galvanised special clips, bolts and nuts etc.75 mm. x 75 mm. x 6 g. |
| 12 | M.S. gate of Jail type as per approved design made of strong M.S. frame work, intermediate stiffeners and round / square bars or angles. M.S. sheet (not less than 14 gauge) gussets, cleats etc. including necessary riveting, bolting, welding, locking and hanging arrangements, fitting and fixing complete as per direction of the Engineer-in -charge.In ground floor |
| 13 | Supplying fitting & fixing FRP Sprial Slide : Platform height - 5.5’’, DIAMETER: 5’ ; Structural parts made of GI pipes and MS hollow section (including cutting, fitting, welding, bolting and smoothing grinding etc. complete). Entire product is assembled with nut bolts. Outer diameter of metal parts: 76, 26.9, thickness of metal parts: min 2.9mm, slide MOC: FRP, FRP thickness: 6mm to 12mm, FRP density: 1600kg/m3. Color: multicolor ASPA finish paint on 2 coats of primer. Area: DIA: 6’ |
| 14 | Supplying fitting & fixing Duck MGR : DIAMETER: 5.5’The machine assy. / joint portion (on which the MGR rotates) should has heavy duty ball bearing. Structural parts made of GI pipes and MS hollow section (including cutting, fitting, welding, bolting and smoothing grinding etc. complete). Entire product is assembled with nut bolts. Outer diameter of metal parts: 26.9, thickness of metal parts: min 2.9mm, dolls MOC: FRP, doll-4no (duck), FRP thickness: 6mm to 8mm, FRP density: 1600kg/m^3. Color: multicolor ASPA finish paint on 2 coats of primer. Area: DIA 6‘ |
| 15 | Supplying fitting & fixing Circular Swing : Height –5’, ,Width-5’ The machine assy. / joint portion should has heavy duty ball bearing. Structural parts made of GI pipes and MS hollow section (including cutting, fitting, welding, bolting and smoothing grinding etc. complete). Entire product is assembled with nut bolts. Outer diameter of metal parts: 42.1, 48.3, 26.9, thickness of metal parts: min 2.9mm, seat MOC: FRP, FRP thickness: 6mm to 8mm, FRP density: 1600kg/m^3. Color: multicolor ASPA finish paint on 2 coats of primer. Area: 6’ X 6‘ |
| 16 | Supplying fitting & fixing Bench: Length –5’, Handle –with designing C.I. casting, Seat: M.S. Hollow pipe with 75mm x 25mm and 50mm x 25mm section, No of strip-10 nos , Color: multicolor ASPA finish paint on 2 coats of primer. Area: 6’ X 2 .5‘ |
| 17 | Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc. |
| 18 | Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary :On steel or other metal surface : With super gloss (hi-gloss) -Two coats (with any shade except white) Please Enable Macros to View BoQ information |
