|
| 1 | Providing and fixing Tank Type (Make of Metal) Fertilizer and Chemical Injector System confirming to IS 14483 (Part 3) of 2018 for demonstration and guiding the farmers regarding fertilization and chemicalisation of system. (rates include ventury with manifold 1.0`=1300 and 60 liter fertilizer tank= 4400 ) rate approved by worthy Administrator |
| 2 | Horizontal directional drilling with micro tunnelling methods, for pipe laying under pacca rast/road crossing |
| 3 | Galvanizes steel chain link both end twisted fence fabric having opening size 7.5x7.5 cm and 3.15 mm dia wire, 2.2 meter height of mesh, with 2.8 meter ht of MS Angle 50x50x5 mm supports fixing at spacing of 3 meter centre to centre, supports with MS Flat 35x5 mm. Fencing supported with MS Angle 35x35x5 at top and bottom. The M.S Angle supports shall be anchored in cement concrete (1:3:6) blocks 45x45x60 cm additional razor barbed wire fencing shall be provided at the top of mesh, fencing including gate |
| 4 | Providing and fixing 12 Watt LED Street Lighting of 75 watt solar panel, 12.8 volt 30 Ah Lithium Ferro Phosphate battery, 12 Watt White LED Luminaire and Pole of 5 Meter above ground level with dusk to dawn operation {first 4 hours full light Systemding, fixing and testing of Solar light including battery: min. 24 lux) , rest of the time at lower light (50% Min. 12 lux) level} and 3 days or minimum 36 operating hours autonomy or as per direction of engineer-in-charge |
| 5 | Providing fixing of Header Assembly/Manifold 3` to connenct the filtration unit (loose) |
| 6 | Providing fixing of Header Assembly/Manifold 3` to connenct the filtration unit (loose) |
| 7 | providing and fixing of 3` plastic hydraulic control valve threaded (quick pressure relief) |
| 8 | providing and fixing of 1.5` plastic air cum vacuum relief valve. |
| 9 | providing , fixing , testing and commissioning of 2.5` Dial pressure Gauge. |
| 10 | providing and fixing of 2` continuous acting air cum vacuum relief valve. |
| 11 | Complete operation and Maintenance and watch and ward of the project for one year including operation of pump, pipe line, accessories, electromechanical, solar plantscomplet in all respect of pump house, pipe line and accessories, electromechanical, solar plant etc complete in allrespect for one year |
| 12 | Providing and fixing of AC Submersible pump set with three phase 50Hz ±3% rated motor frequency, 415V ± 3% rated motor voltage, (Submersible motors shall conform to all the requirements of IS 9283) Solar A.C. Agricultural Pumps alongwith Universal Solar Pump Controller (USPC). All external part of motor used in open well submersible pump having casing of Alloy steel confirming to IS 3444 As per IS code 14220-2018 including third party inspection.Average discharge 13 LPS / Head 52 meter / minimum / minimum output rating of 15 KW duly installed on the suitable foundation. Actual pump set`s parameters will be finalized after approval of design and drawing. Solar Pumping Sets should be of the make: KSB / Shakti/ Kirloskar /CRI/Lubi/ Crompton/ WPIL (AC Submersible pump set 5 HP) |
| 13 | Supply, installation, Testing and Commissioning of VFD Drive for Pumps (5HP) |
| 14 | Supply, installation, Testing and Commissioning of VFD Drive for Pumps (7.5) |
| 15 | Supply Installation testing commissioning of Solar Photovoltaic Stand alone Plant conforming to MNRE specifications as amended, consisting of Mono Crystalline silicon solar cells, necessary protections, earthing, mounted on Aluminum/GI structure of suitable strength, anti-theft screws. Including lightning and surge voltage protection, fixing of Array junction box and Main junction box with IP 65 protection and termination arrangement for incoming and outgoing cable along with glands, lugs and other accessories etc. as required, built in metering system to monitor plant performance (Amp-meter, Vold-meter, Frequency meter, Energy meter, Watt-meter, and other instrument/equipment as required) Note:- PV modules used must qualify to the latest edition of IEC PV module qualification test or equivalent BIS standards Mono Crystalline Silicon Solar Cell Modules IEC 61215/IS14286. In addition, the modules must conform to IEC 61730 Part-1- requirements for construction and Part 2 – requirements for testing, for safety qualification or equivalent IS and be mounted on fixed Aluminum/GI structure of adequate strength and design as per IEC/IS specification. Including field-based electroluminescence (EL) study be performed after receiving the modules at site and after installation. Module mounting structure (MMS) including suitable foundation, design and drawing shall be duly vetted from government institute including third party inspection. |
| 16 | Supplying, erection, testing and commissioning of Solar AC Open-well Submersible Pump Set with three phase motor having casing of Alloy Steel for the required power capacity, discharge and Head including all PVC insulated polymer sheathed 3 core flat type cabling in conduit, required from solar plant to solar pump through control room. (7.5HP) |
| 17 | Providing, laying, aligning, and jointing at all level/ depths ISI marked HDPE pipe of PE 80 Grade SDR 17 PN 6 for irrigation as per IS 4984-2016 amended up to date in trenches in complete, including cost of HDPE Specials, labor, sectional hydraulic testing (including to cost of conveyance of water to site for testing ) and commissioning as per Technical Specifications and approved make as per direction of Engineer rates include cost of all specials like bends , tees required during laying of pipeline along required alignment. Dia. 140MM |
| 18 | Providing, laying, aligning, and jointing with uPVC heavy body solvent at all level/ depths OF Type B , class 2(4kg/cm2) ISI marked uPVC pipe of pressure as per design for raw water supply as per IS 4985:2021 (amended up to date)including cost of special,labour,sectional hydro testing in trenches in complete, including cost of all Specials, labor, and commissioning as per Technical Specifications and approved make as per direction of Engineer. Rates includes cost of all special like bend , tees required during laying of pipe line along required alignment. 110mm uPVC Pipes |
| 19 | Providing, laying, aligning, and jointing with uPVC heavy body solvent at all level/ depths OF Type B , class 2(4kg/cm2) ISI marked uPVC pipe of pressure as per design for raw water supply as per IS 4985:2021 (amended up to date)including cost of special,labour,sectional hydro testing in trenches in complete, including cost of all Specials, labor, and commissioning as per Technical Specifications and approved make as per direction of Engineer. Rates includes cost of all special like bend , tees required during laying of pipe line along required alignment. 110mm uPVC Pipes |
| 20 | Providing and lowering of HDPE floater manufactured with 225 mm dia PE pipe having PE -80 and PN 10 to float the submersible open well pump / motor. |
| 21 | Civil Work |
| 22 | Total for HSR Items for the work Installation of Solar powered pressurised irrigation infrastructure at overflowing village Pond Basanti Mata Johad of Village Nawagaon, Block Barwala and solar powered pressurized irrigation infrastructure at overflowing village pond Sarakpur, Block Raipurrani, District Panchkula. Please Enable Macros to View BoQ information |
