Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | Scheme 1-Providing MS shutters, hoisting bridge and mechanism for various off take shutters and cross regulators at LBC Malampuzha under Koduvayur Section. |
| 2 | OD29465/2023-2024:Taking out the mud debris and cleaning the bay, removing the plastic and bio waste and disposing at a suitable place 50m away from site |
| 3 | OD26330/2023-2024:Dismantling of the Canal Shutter ( Up to 2 Tonne weight )/ Hoisting unit, Embedded parts, etc. of the same and stacking at a distance of 100 metre including hire of machinery, labour etc. complete as directed by the departmental officer at site. (Weight of the unserviceable shutters and embedded parts may be calculated as 60% and unserviceable hoisting units as 80%) |
| 4 | 15.2.1:Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 5 | 2.6.1:Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil |
| 6 | 2.25:Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m. |
| 7 | 5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete |
| 8 | 5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more |
| 9 | 5.1.2:Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size |
| 10 | 13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) |
| 11 | OD26329/2023-2024:Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges |
| 12 | OD26328/2023-2024:Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges |
| 13 | OD29469/2023-2024:Supply of MS round bar including cost of conveyance charges |
| 14 | OD26327/2023-2024:Supply of MS BOLT and NUT up to 300mm Length including cost of conveyance. |
| 15 | OD29706/2023-2024:Fabrication, Supply, erection and assembling in correct position and alignment by welding SS Embedded parts in 304L Grade like roller track, seal track, Seal seat etc. as per approved specifications, drawings and directions of deptl. officer at site including cost of all materials, labour, machinery for planing, welding, shearing, grinding etc., lead and lift, conveyance, incidental and handling etc. complete |
| 16 | OD26333/2023-2024:Fabrication and erection of Embedded parts of Canal shutters ( Up to 2 tonne weight ) and accessories as per approved specifications, drawings and directions of deptl. officer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc. complete but excluding cost of material already supplied |
| 17 | OD29483/2023-2024:Fabrication and supply of Structural steel Canal shutters ( Up to 2 tonne weight ) /Hoisting bridge/ Platform and accessories etc. as per approved specifications, drawings and directions of deptl. officer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc. complete but excluding cost of material already supplied |
| 18 | 85.116:Supplying and fixing in correct position with specified initial interface the flat type rubber seal confirming to IS 11855 to the gates including cost of SS bolts and nut all labour and machinery and incidental and conveyance charges complete as per approved specification and drawing |
| 19 | 85.118:Supplying and fixing in correct position with specified initial interface L-type / bulb nose rubber seal confirming to IS11855 to the gates including cost of SS bolts and nuts and all labour and machinery and incidental and conveyance charges complete as per approved specifications and drawings |
| 20 | OD29476/2023-2024:Providing of worm and pinion having a lifting speed of around 5.00 cm/min for hand operation including cost of all materials, labour, hire charges and conveyance. |
| 21 | OD29477/2023-2024:Providing base and nut arrangement for hoisting the shutter including cost of all materials, labour, etc. complete |
| 22 | OD29479/2023-2024:Providing EN-8 screw rod 7.50 tonne capacity 4.00 M lift screw hoist having one number of EN-8 screw shaft, worm gear units having a lifting speed of around 5.00 cm/min for 24 rpm of hand operation including cost of all materials, labour, hire charges and conveyance. 1m Screw rod, dia 67mm with single start square thread with head pitch of 12.7mm, root dia 62.3mm EN -8 shaft |
| 23 | OD29481/2023-2024:THREAD LESS portion of the screw rod (per metre rate) |
| 24 | OD29480/2023-2024:SUPPLYING and APPLYING GREASE on NEW SCREW ROD for CANAL GATE |
| 25 | 85.114:Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc on dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350 microns after cleaning the surface using hand and power tool cleaning including cost of all materials, labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site |
| 26 | OD26331/2023-2024:Erection of the Canal Shutter ( Up to 2 Tonne weight ) / Hoisting bridge/ Platform including hand rails, ladder etc. for the same including alignment correcting and setting complete including cost of all labour, machinery, incidental and conveyance, lead and lift charges etc. complete but excluding cost of materials already supplied |
| 27 | Scheme 2-Providing Gate valve arrangements for various sluices at LB main canal and Erimayur branch canal under Koduvayur Section (Total 12nos in LB main canal and 47nos in Erimayur branch canal) |
| 28 | OD29595/2023-2024:Taking out the mud debris and cleaning the bay, removing the plastic and bio waste and disposing at a suitable place 50m away from site |
| 29 | OD29596/2023-2024:Dismantling of the Canal Shutter ( Up to 2 Tonne weight )/ Hoisting unit, Embedded parts, etc. of the same and stacking at a distance of 100 metre including hire of machinery, labour etc. complete as directed by the departmental officer at site. (Weight of the unserviceable shutters and embedded parts may be calculated as 60% and unserviceable hoisting units as 80%) |
| 30 | 15.2.1:Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 31 | 2.6.1:Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil |
| 32 | 2.25:Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m. |
| 33 | 5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete |
| 34 | 4.1.8:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size) |
| 35 | 5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more |
| 36 | 5.1.2:Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size |
| 37 | 13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) |
| 38 | 18.72.19:Providing and laying S & S Centrifugally Cast (Spun) / Ductile Iron Pipes conforming to IS : 8329:300 mm dia Ductile iron Class K-9 pipes |
| 39 | OD29767/2023-2024:Supply of dia 12" slip-on flange. |
| 40 | OD29850/2023-2024:Labour charges for cutting 300mm DI pipe diametrically, the cut being perpendicular to the axis of pipe with steel saw and smoothening of the cut end etc. complete. |
| 41 | OD29849/2023-2024:Welding charges for fixing additional DI flanges to DI pipe with suitable welding rod including cost of labour, machinery, consumables, incidental and handling charges etc. complete butexcluding material already supplied. |
| 42 | OD29758/2023-2024:Supply of 12" Gate valve, ANSI 150,OS&Y Structure, flanged ends (Flange dimensions as per ANSI B16.5), bolted bonnet. Valve body: cast iron or WCBStem and disc: stainless steel, Hand wheel with locking arrangements, vertical operated. Valve tested to applicable International standards. Working fluid: water. |
| 43 | OD29756/2023-2024:Conveying and fixing gate valves by providing bolts, nuts, rubber insertions, etc., complete, but excluding the cost of the valve (tail pieces, if required , will be paid separately): 300mm diameter , Class I. |
| 44 | OD29856/2023-2024:Supply and fixing of fabricated strainer 300mm dia including the cost of material, labour, conveyance, etc. complete. |
| 45 | OD29859/2023-2024:Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges |
| 46 | OD29858/2023-2024:Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges |
| 47 | OD29857/2023-2024:Supply of MS round bar including cost of conveyance charges |
| 48 | OD29860/2023-2024:Supply of MS chequered plates including cost of conveyance charges |
| 49 | OD29862/2023-2024:BUTT HINGE |
| 50 | OD29863/2023-2024:SUPPLYING & FIXING of TOWER BOLT |
| 51 | OD29861/2023-2024:SUPPLYING and STACKING of PAD LOCK. |
| 52 | OD29864/2023-2024:Fabrication and supply of Structural steel Canal shutters ( Up to 2 tonne weight ) /Hoisting bridge/ Platform and accessories etc. as per approved specifications, drawings and directions of deptl. officer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc. complete but excluding cost of material already supplied |
| 53 | 85.114:Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc on dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350 microns after cleaning the surface using hand and power tool cleaning including cost of all materials, labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site |
| 54 | OD29865/2023-2024:Erection of the Canal Shutter ( Up to 2 Tonne weight ) / Hoisting bridge/ Platform including hand rails, ladder etc. for the same including alignment correcting and setting complete including cost of all labour, machinery, incidental and conveyance, lead and lift charges etc. complete but excluding cost of materials already supplied |
| 55 | Scheme 3-Providing MS shutters, hoisting bridge and mechanism for various Head sluices at Ch:01/900, Ch:04/000, Ch:08/190, Ch:12/900, Ch:14/200, Ch:09/700, Ch:10/610, Ch:11/080, Ch:14/290 (Total 9nos) under Palakkad Section |
| 56 | OD41552/2023-2024:Taking out the mud debris and cleaning the bay, removing the plastic and bio waste and disposing at a suitable place 50m away from site |
| 57 | OD41553/2023-2024:Dismantling of the Canal Shutter ( Up to 2 Tonne weight )/ Hoisting unit, Embedded parts, etc. of the same and stacking at a distance of 100 metre including hire of machinery, labour etc. complete as directed by the departmental officer at site. (Weight of the unserviceable shutters and embedded parts may be calculated as 60% and unserviceable hoisting units as 80%) |
| 58 | 15.2.1:Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 59 | 2.6.1:Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil |
| 60 | 2.25:Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m. |
| 61 | 5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete |
| 62 | 5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more |
| 63 | 5.1.2:Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size |
| 64 | 13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) |
| 65 | OD41606/2023-2024:Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges |
| 66 | OD41611/2023-2024:Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges |
| 67 | OD41621/2023-2024:Supply of MS round bar including cost of conveyance charges |
| 68 | OD41637/2023-2024:Supply of MS BOLT and NUT up to 300mm Length including cost of conveyance. |
| 69 | OD41639/2023-2024:Fabrication, Supply, erection and assembling in correct position and alignment by welding SS Embedded parts in 304L Grade like roller track, seal track, Seal seat etc. as per approved specifications, drawings and directions of deptl. officer at site including cost of all materials, labour, machinery for planing, welding, shearing, grinding etc., lead and lift, conveyance, incidental and handling etc. complete |
| 70 | OD41640/2023-2024:Fabrication and erection of Embedded parts of Canal shutters ( Up to 2 tonne weight ) and accessories as per approved specifications, drawings and directions of deptl. officer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc. complete but excluding cost of material already supplied |
| 71 | OD41643/2023-2024:Fabrication and supply of Structural steel Canal shutters ( Up to 2 tonne weight ) /Hoisting bridge/ Platform and accessories etc. as per approved specifications, drawings and directions of deptl. officer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc. complete but excluding cost of material already supplied |
| 72 | 85.116:Supplying and fixing in correct position with specified initial interface the flat type rubber seal confirming to IS 11855 to the gates including cost of SS bolts and nut all labour and machinery and incidental and conveyance charges complete as per approved specification and drawing |
| 73 | 85.118:Supplying and fixing in correct position with specified initial interface L-type / bulb nose rubber seal confirming to IS11855 to the gates including cost of SS bolts and nuts and all labour and machinery and incidental and conveyance charges complete as per approved specifications and drawings |
| 74 | OD41659/2023-2024:Providing base and nut arrangement for hoisting the shutter including cost of all materials, labour, etc. complete |
| 75 | OD41660/2023-2024:Providing EN-8 screw rod 7.50 tonne capacity 4.00 M lift screw hoist having one number of EN-8 screw shaft, worm gear units having a lifting speed of around 5.00 cm/min for 24 rpm of hand operation including cost of all materials, labour, hire charges and conveyance. 1m Screw rod, dia 67mm with single start square thread with head pitch of 12.7mm, root dia 62.3mm EN -8 shaft |
| 76 | OD41662/2023-2024:THREAD LESS portion of the screw rod (per metre rate) |
| 77 | OD41663/2023-2024:SUPPLYING and APPLYING GREASE on NEW SCREW ROD for CANAL GATE |
| 78 | 85.114:Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc on dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350 microns after cleaning the surface using hand and power tool cleaning including cost of all materials, labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site |
| 79 | OD41667/2023-2024:Erection of the Canal Shutter ( Up to 2 Tonne weight ) / Hoisting bridge/ Platform including hand rails, ladder etc. for the same including alignment correcting and setting complete including cost of all labour, machinery, incidental and conveyance, lead and lift charges etc. complete but excluding cost of materials already supplied |
| 80 | Scheme 4-Providing Gate valve arrangements for various sluices at LB main canal Direct sluices from Ch:0/690 to Ch:19/100 (Total 31nos) and Kadalakurissi Direct sluices from Ch:0/272 to Ch:08/400 (Total 24nos) under Palakkad Section |
| 81 | OD41668/2023-2024:Taking out the mud debris and cleaning the bay, removing the plastic and bio waste and disposing at a suitable place 50m away from site |
| 82 | OD41669/2023-2024:Dismantling of the Canal Shutter ( Up to 2 Tonne weight )/ Hoisting unit, Embedded parts, etc. of the same and stacking at a distance of 100 metre including hire of machinery, labour etc. complete as directed by the departmental officer at site. (Weight of the unserviceable shutters and embedded parts may be calculated as 60% and unserviceable hoisting units as 80%) |
| 83 | 15.9.2:Demolishing stone rubble masonry manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer -in- Charges:In cement mortar |
| 84 | 15.2.1:Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 85 | 2.6.1:Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil |
| 86 | 2.25:Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m. |
| 87 | 5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete |
| 88 | 4.1.8:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size) |
| 89 | 5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more |
| 90 | 5.1.2:Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size |
| 91 | 13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) |
| 92 | 18.72.19:Providing and laying S & S Centrifugally Cast (Spun) / Ductile Iron Pipes conforming to IS : 8329:300 mm dia Ductile iron Class K-9 pipes |
| 93 | OD41671/2023-2024:Supply of 12 inch dia slip-on flange. |
| 94 | OD41672/2023-2024:Labour charges for cutting 300mm DI pipe diametrically, the cut being perpendicular to the axis of pipe with steel saw and smoothening of the cut end etc. complete. |
| 95 | OD41673/2023-2024:Welding charges for fixing additional DI flanges to DI pipe with suitable welding rod including cost of labour, machinery, consumables, incidental and handling charges etc. complete butexcluding material already supplied. |
| 96 | OD41674/2023-2024:Supply of 12" Gate valve, ANSI 150,OS&Y Structure, flanged ends (Flange dimensions as per ANSI B16.5), bolted bonnet. Valve body: cast iron or WCBStem and disc: stainless steel, Hand wheel with locking arrangements, vertical operated. Valve tested to applicable International standards. Working fluid: water. |
| 97 | OD41675/2023-2024:Conveying and fixing gate valves by providing bolts, nuts, rubber insertions, etc., complete, but excluding the cost of the valve (tail pieces, if required , will be paid separately): 300mm diameter , Class I. |
| 98 | OD41676/2023-2024:Supply and fixing of fabricated strainer 300mm dia including the cost of material, labour, conveyance, etc. complete. |
| 99 | OD41677/2023-2024:Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges |
| 100 | OD41678/2023-2024:Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges |
| 101 | OD41679/2023-2024:Supply of MS round bar including cost of conveyance charges |
| 102 | OD41681/2023-2024:Supply of MS chequered plates including cost of conveyance charges |
| 103 | OD41682/2023-2024:BUTT HINGE |
| 104 | OD41683/2023-2024:SUPPLYING & FIXING of TOWER BOLT |
| 105 | OD41684/2023-2024:SUPPLYING and STACKING of PAD LOCK. |
| 106 | OD41685/2023-2024:Fabrication and supply of Steel structures confirming to IS2062 Gr including chequered plates for platform, covers for hoisting unit etc as per approved specifications, drawings and directions of departmental officer at site including cost of labour, machinery, incidental and handling charges etc complete but excluding material already supplied and weight of pipes for hand rails etc |
| 107 | 85.114:Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc on dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350 microns after cleaning the surface using hand and power tool cleaning including cost of all materials, labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site |
| 108 | OD41686/2023-2024:Erection of the Canal Shutter ( Up to 2 Tonne weight ) / Hoisting bridge/ Platform including hand rails, ladder etc. for the same including alignment correcting and setting complete including cost of all labour, machinery, incidental and conveyance, lead and lift charges etc. complete but excluding cost of materials already supplied |
| 109 | Scheme 5-Providing MS shutter, hoisting bridge and mechanism for Kodunthirappully cross regulator (1no), Edathara head sluice (1no) and Kodunthirappully cross shutter at Ch:10/600Km (1no) under Palakkad Section |
| 110 | OD41690/2023-2024:Taking out the mud debris and cleaning the bay, removing the plastic and bio waste and disposing at a suitable place 50m away from site |
| 111 | OD41691/2023-2024:Dismantling of the Canal Shutter ( Up to 2 Tonne weight )/ Hoisting unit, Embedded parts, etc. of the same and stacking at a distance of 100 metre including hire of machinery, labour etc. complete as directed by the departmental officer at site. (Weight of the unserviceable shutters and embedded parts may be calculated as 60% and unserviceable hoisting units as 80%) |
| 112 | 15.2.1:Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 113 | 5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete |
| 114 | 5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more |
| 115 | 5.1.2:Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size |
| 116 | 4.1.5:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) |
| 117 | 13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) |
| 118 | OD41693/2023-2024:Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges |
| 119 | OD41694/2023-2024:Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges |
| 120 | OD41695/2023-2024:Supply of MS chequered plates including cost of conveyance charges |
| 121 | OD41696/2023-2024:Supply of MS round bar including cost of conveyance charges |
| 122 | OD41697/2023-2024:Supply of MS BOLT and NUT up to 300mm Length including cost of conveyance. |
| 123 | OD41698/2023-2024:Fabrication, Supply, erection and assembling in correct position and alignment by welding SS Embedded parts in 304L Grade like roller track, seal track, Seal seat etc. as per approved specifications, drawings and directions of deptl. officer at site including cost of all materials, labour, machinery for planing, welding, shearing, grinding etc., lead and lift, conveyance, incidental and handling etc. complete |
| 124 | OD41699/2023-2024:Fabrication and erection of Embedded parts of Canal shutters ( Up to 2 tonne weight ) and accessories as per approved specifications, drawings and directions of deptl. officer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc. complete but excluding cost of material already supplied |
| 125 | OD41700/2023-2024:Fabrication and supply of Structural steel Canal shutters ( Up to 2 tonne weight ) /Hoisting bridge/ Platform and accessories etc. as per approved specifications, drawings and directions of deptl. officer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc. complete but excluding cost of material already supplied |
| 126 | 85.116:Supplying and fixing in correct position with specified initial interface the flat type rubber seal confirming to IS 11855 to the gates including cost of SS bolts and nut all labour and machinery and incidental and conveyance charges complete as per approved specification and drawing |
| 127 | 85.118:Supplying and fixing in correct position with specified initial interface L-type / bulb nose rubber seal confirming to IS11855 to the gates including cost of SS bolts and nuts and all labour and machinery and incidental and conveyance charges complete as per approved specifications and drawings |
| 128 | OD41701/2023-2024:Providing of worm and pinion having a lifting speed of around 5.00 cm/min for hand operation including cost of all materials, labour, hire charges and conveyance. |
| 129 | OD41702/2023-2024:Providing base and nut arrangement for hoisting the shutter including cost of all materials, labour, etc. complete |
| 130 | OD41703/2023-2024:Providing EN-8 screw rod 7.50 tonne capacity 4.00 M lift screw hoist having one number of EN-8 screw shaft, worm gear units having a lifting speed of around 5.00 cm/min for 24 rpm of hand operation including cost of all materials, labour, hire charges and conveyance. 1m Screw rod, dia 67mm with single start square thread with head pitch of 12.7mm, root dia 62.3mm EN -8 shaft |
| 131 | OD41704/2023-2024:THREAD LESS portion of the screw rod (per metre rate) |
| 132 | OD41705/2023-2024:SUPPLYING and APPLYING GREASE on NEW SCREW ROD for CANAL GATE |
| 133 | 85.114:Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc on dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350 microns after cleaning the surface using hand and power tool cleaning including cost of all materials, labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site |
| 134 | OD41708/2023-2024:Erection of the Canal Shutter ( Up to 2 Tonne weight ) / Hoisting bridge/ Platform including hand rails, ladder etc. for the same including alignment correcting and setting complete including cost of all labour, machinery, incidental and conveyance, lead and lift charges etc. complete but excluding cost of materials already supplied |
| 135 | Scheme 6-Providing Gate valve arrangements at various chainages of Kodunthirappully branch canal (18nos), Kottekkad-1 branch canal (5nos) under Palakkad Section |
| 136 | OD41715/2023-2024:Taking out the mud debris and cleaning the bay, removing the plastic and bio waste and disposing at a suitable place 50m away from site |
| 137 | OD41716/2023-2024:Dismantling of the Canal Shutter ( Up to 2 Tonne weight )/ Hoisting unit, Embedded parts, etc. of the same and stacking at a distance of 100 metre including hire of machinery, labour etc. complete as directed by the departmental officer at site. (Weight of the unserviceable shutters and embedded parts may be calculated as 60% and unserviceable hoisting units as 80%) |
| 138 | 15.2.1:Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 139 | 2.6.1:Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil |
| 140 | 2.25:Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m. |
| 141 | 5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete |
| 142 | 4.1.8:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size) |
| 143 | 5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more |
| 144 | 5.1.2:Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size |
| 145 | 13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) |
| 146 | 18.72.19:Providing and laying S & S Centrifugally Cast (Spun) / Ductile Iron Pipes conforming to IS : 8329:300 mm dia Ductile iron Class K-9 pipes |
| 147 | OD41719/2023-2024:Supply of dia 12" slip-on flange. |
| 148 | OD41720/2023-2024:Labour charges for cutting 300mm DI pipe diametrically, the cut being perpendicular to the axis of pipe with steel saw and smoothening of the cut end etc. complete. |
| 149 | OD41721/2023-2024:Welding charges for fixing additional DI flanges to DI pipe with suitable welding rod including cost of labour, machinery, consumables, incidental and handling charges etc. complete butexcluding material already supplied. |
| 150 | OD41726/2023-2024:Supply of 12" Gate valve, ANSI 150,OS&Y Structure, flanged ends (Flange dimensions as per ANSI B16.5), bolted bonnet. Valve body: cast iron or WCBStem and disc: stainless steel, Hand wheel with locking arrangements, vertical operated. Valve tested to applicable International standards. Working fluid: water. |
| 151 | OD41723/2023-2024:Conveying and fixing gate valves by providing bolts, nuts, rubber insertions, etc., complete, but excluding the cost of the valve (tail pieces, if required , will be paid separately): 300mm diameter , Class I. |
| 152 | OD41727/2023-2024:Supply and fixing of fabricated strainer 300mm dia including the cost of material, labour, conveyance, etc. complete. |
| 153 | OD41728/2023-2024:Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges |
| 154 | OD41729/2023-2024:Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges |
| 155 | OD41731/2023-2024:Supply of MS round bar including cost of conveyance charges |
| 156 | OD41732/2023-2024:Supply of MS chequered plates including cost of conveyance charges |
| 157 | OD41734/2023-2024:BUTT HINGE |
| 158 | OD41735/2023-2024:SUPPLYING & FIXING of TOWER BOLT |
| 159 | OD41733/2023-2024:SUPPLYING and STACKING of PAD LOCK. |
| 160 | OD41736/2023-2024:Fabrication and supply of Structural steel Canal shutters ( Up to 2 tonne weight ) /Hoisting bridge/ Platform and accessories etc. as per approved specifications, drawings and directions of deptl. officer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc. complete but excluding cost of material already supplied |
| 161 | 85.114:Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc on dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350 microns after cleaning the surface using hand and power tool cleaning including cost of all materials, labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site |
| 162 | OD41737/2023-2024:Erection of the Canal Shutter ( Up to 2 Tonne weight ) / Hoisting bridge/ Platform including hand rails, ladder etc. for the same including alignment correcting and setting complete including cost of all labour, machinery, incidental and conveyance, lead and lift charges etc. complete but excluding cost of materials already supplied |
| 163 | Scheme 7-Providing MS shutter, hoisting bridge and mechanism for Edathara branch cross shutter at Ch:10/450Km under Palakkad Section |
| 164 | OD41743/2023-2024:Taking out the mud debris and cleaning the bay, removing the plastic and bio waste and disposing at a suitable place 50m away from site |
| 165 | OD41744/2023-2024:Dismantling of the Canal Shutter ( Up to 2 Tonne weight )/ Hoisting unit, Embedded parts, etc. of the same and stacking at a distance of 100 metre including hire of machinery, labour etc. complete as directed by the departmental officer at site. (Weight of the unserviceable shutters and embedded parts may be calculated as 60% and unserviceable hoisting units as 80%) |
| 166 | 15.2.1:Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 167 | 5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete |
| 168 | 5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more |
| 169 | 5.1.2:Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size |
| 170 | 4.1.5:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) |
| 171 | 13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) |
| 172 | OD41747/2023-2024:Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges |
| 173 | OD41746/2023-2024:Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges |
| 174 | OD41745/2023-2024:Supply of MS round bar including cost of conveyance charges |
| 175 | OD41750/2023-2024:Supply of MS BOLT and NUT up to 300mm Length including cost of conveyance. |
| 176 | OD41751/2023-2024:Fabrication, Supply, erection and assembling in correct position and alignment by welding SS Embedded parts in 304L Grade like roller track, seal track, Seal seat etc. as per approved specifications, drawings and directions of deptl. officer at site including cost of all materials, labour, machinery for planing, welding, shearing, grinding etc., lead and lift, conveyance, incidental and handling etc. complete |
| 177 | OD41752/2023-2024:Fabrication and erection of Embedded parts of Canal shutters ( Up to 2 tonne weight ) and accessories as per approved specifications, drawings and directions of deptl. officer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc. complete but excluding cost of material already supplied |
| 178 | OD41754/2023-2024:Fabrication and supply of Structural steel Canal shutters ( Up to 2 tonne weight ) /Hoisting bridge/ Platform and accessories etc. as per approved specifications, drawings and directions of deptl. officer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc. complete but excluding cost of material already supplied |
| 179 | 85.116:Supplying and fixing in correct position with specified initial interface the flat type rubber seal confirming to IS 11855 to the gates including cost of SS bolts and nut all labour and machinery and incidental and conveyance charges complete as per approved specification and drawing |
| 180 | 85.118:Supplying and fixing in correct position with specified initial interface L-type / bulb nose rubber seal confirming to IS11855 to the gates including cost of SS bolts and nuts and all labour and machinery and incidental and conveyance charges complete as per approved specifications and drawings |
| 181 | OD41756/2023-2024:Providing base and nut arrangement for hoisting the shutter including cost of all materials, labour, etc. complete |
| 182 | OD41761/2023-2024:Providing EN-8 screw rod 7.50 tonne capacity 4.00 M lift screw hoist having one number of EN-8 screw shaft, worm gear units having a lifting speed of around 5.00 cm/min for 24 rpm of hand operation including cost of all materials, labour, hire charges and conveyance. 1m Screw rod, dia 67mm with single start square thread with head pitch of 12.7mm, root dia 62.3mm EN -8 shaft |
| 183 | OD41762/2023-2024:THREAD LESS portion of the screw rod (per metre rate) |
| 184 | OD41763/2023-2024:SUPPLYING and APPLYING GREASE on NEW SCREW ROD for CANAL GATE |
| 185 | 85.114:Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc on dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350 microns after cleaning the surface using hand and power tool cleaning including cost of all materials, labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site |
| 186 | OD41764/2023-2024:Erection of the Canal Shutter ( Up to 2 Tonne weight ) / Hoisting bridge/ Platform including hand rails, ladder etc. for the same including alignment correcting and setting complete including cost of all labour, machinery, incidental and conveyance, lead and lift charges etc. complete but excluding cost of materials already supplied |
| 187 | Scheme 8-Providing Gate valve arrangements at various chainages of Edathara branch canal (41nos), Edathara-Pirayiri branch canal (3nos) under Palakkad Section |
| 188 | OD41765/2023-2024:Taking out the mud debris and cleaning the bay, removing the plastic and bio waste and disposing at a suitable place 50m away from site |
| 189 | OD41766/2023-2024:Dismantling of the Canal Shutter ( Up to 2 Tonne weight )/ Hoisting unit, Embedded parts, etc. of the same and stacking at a distance of 100 metre including hire of machinery, labour etc. complete as directed by the departmental officer at site. (Weight of the unserviceable shutters and embedded parts may be calculated as 60% and unserviceable hoisting units as 80%) |
| 190 | 15.2.1:Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 191 | 2.6.1:Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead up to 50 m and lift up to 1.5 m, disposed earth to be levelled and neatly dressed.All kinds of soil |
| 192 | 2.25:Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m. |
| 193 | 5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete |
| 194 | 4.1.8:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 nominal size) |
| 195 | 5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more |
| 196 | 5.1.2:Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size |
| 197 | 13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) |
| 198 | 18.72.19:Providing and laying S & S Centrifugally Cast (Spun) / Ductile Iron Pipes conforming to IS : 8329:300 mm dia Ductile iron Class K-9 pipes |
| 199 | OD41771/2023-2024:Supply of dia 12" slip-on flange. |
| 200 | OD41772/2023-2024:Labour charges for cutting 300mm DI pipe diametrically, the cut being perpendicular to the axis of pipe with steel saw and smoothening of the cut end etc. complete. |
| 201 | OD41773/2023-2024:Welding charges for fixing additional DI flanges to DI pipe with suitable welding rod including cost of labour, machinery, consumables, incidental and handling charges etc. complete butexcluding material already supplied. |
| 202 | OD41774/2023-2024:Supply of 12" Gate valve, ANSI 150,OS&Y Structure, flanged ends (Flange dimensions as per ANSI B16.5), bolted bonnet. Valve body: cast iron or WCBStem and disc: stainless steel, Hand wheel with locking arrangements, vertical operated. Valve tested to applicable International standards. Working fluid: water. |
| 203 | OD41775/2023-2024:Conveying and fixing gate valves by providing bolts, nuts, rubber insertions, etc., complete, but excluding the cost of the valve (tail pieces, if required , will be paid separately): 300mm diameter , Class I. |
| 204 | OD41776/2023-2024:Supply and fixing of fabricated strainer 300mm dia including the cost of material, labour, conveyance, etc. complete. |
| 205 | OD41777/2023-2024:Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges |
| 206 | OD41778/2023-2024:Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges |
| 207 | OD41779/2023-2024:Supply of MS round bar including cost of conveyance charges |
| 208 | OD41780/2023-2024:Supply of MS chequered plates including cost of conveyance charges |
| 209 | OD41782/2023-2024:BUTT HINGE |
| 210 | OD41783/2023-2024:SUPPLYING & FIXING of TOWER BOLT |
| 211 | OD41781/2023-2024:SUPPLYING and STACKING of PAD LOCK. |
| 212 | OD41784/2023-2024:Fabrication and supply of Structural steel Canal shutters ( Up to 2 tonne weight ) /Hoisting bridge/ Platform and accessories etc. as per approved specifications, drawings and directions of deptl. officer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc. complete but excluding cost of material already supplied |
| 213 | 85.114:Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc on dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350 microns after cleaning the surface using hand and power tool cleaning including cost of all materials, labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site |
| 214 | OD41785/2023-2024:Erection of the Canal Shutter ( Up to 2 Tonne weight ) / Hoisting bridge/ Platform including hand rails, ladder etc. for the same including alignment correcting and setting complete including cost of all labour, machinery, incidental and conveyance, lead and lift charges etc. complete but excluding cost of materials already supplied |
| 215 | Scheme 9-Provinding new MS shutters, new worm and pinion mechanism with stool arrangements at Karingarapully cross regulator (Ch:12/090), Anappuram cross regulator (Ch: 17/340) of Malampuzha LB main canal under Palakkad section |
| 216 | OD41542/2023-2024:Taking out the mud debris and cleaning the bay, removing the plastic and bio waste and disposing at suitable place 50m away from site |
| 217 | 15.39.3:Dismantling wooden boardings in lining of walls and partitions, excluding supporting members but including stacking with in 50 metres lead:Thickness above 25 mm upto 40 mm |
| 218 | OD41546/2023-2024:Dismantling of the Canal Shutter ( Up to 2 Tonne weight )/ Hoisting unit, Embedded parts, etc. of the same and stacking at a distance of 100 metre including hire of machinery, labour etc. complete as directed by the departmental officer at site. (Weight of the unserviceable shutters and embedded parts may be calculated as 60% and unserviceable hoisting units as 80%) |
| 219 | 15.2.1:Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 220 | 15.9.1:Demolishing stone rubble masonry manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer -in- Charges:In Lime Mortar |
| 221 | 5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete |
| 222 | 4.1.2:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:1/2:3 (cement : 11/2 coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 223 | 5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more |
| 224 | 5.2.2:Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up tot floor five level excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 225 | 13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) |
| 226 | OD41549/2023-2024:Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges |
| 227 | OD41548/2023-2024:Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges |
| 228 | OD41547/2023-2024:Supply of MS round bar including cost of conveyance charges |
| 229 | OD41550/2023-2024:SUPPLYING & STACKING of Dia 32 mm NB (1 1/4'') G.I. PIPE |
| 230 | OD41551/2023-2024:Supply of MS BOLT and NUT up to 300mm Length including cost of conveyance. |
| 231 | OD41605/2023-2024:Fabrication and erection of Embedded parts of Canal shutters ( Up to 2 tonne weight ) and accessories as per approved specifications, drawings and directions of deptl. officer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc. complete but excluding cost of material already supplied |
| 232 | OD41554/2023-2024:Fabrication, Supply, erection and assembling in correct position and alignment by welding SS Embedded parts in 304L Grade like roller track, seal track, Seal seat etc. as per approved specifications, drawings and directions of deptl. officer at site including cost of all materials, labour, machinery for planing, welding, shearing, grinding etc., lead and lift, conveyance, incidental and handling etc. complete |
| 233 | OD41555/2023-2024:Fabrication and supply of Structural steel Canal shutters ( Up to 2 tonne weight ) /Hoisting bridge/ Platform and accessories etc. as per approved specifications, drawings and directions of deptl. officer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc. complete but excluding cost of material already supplied |
| 234 | 85.116:Supplying and fixing in correct position with specified initial interface the flat type rubber seal confirming to IS 11855 to the gates including cost of SS bolts and nut all labour and machinery and incidental and conveyance charges complete as per approved specification and drawing |
| 235 | 85.118:Supplying and fixing in correct position with specified initial interface L-type / bulb nose rubber seal confirming to IS11855 to the gates including cost of SS bolts and nuts and all labour and machinery and incidental and conveyance charges complete as per approved specifications and drawings |
| 236 | OD41556/2023-2024:Providing of Double worm and pinion having a lifting speed of around 5.00 cm/min for hand operation/ manual operation including cost of all materials, labour, hire charges and conveyance. |
| 237 | OD41557/2023-2024:Providing of worm and pinion having a lifting speed of around 5.00 cm/min for hand operation including cost of all materials, labour, hire charges and conveyance. |
| 238 | OD41558/2023-2024:Providing EN-8 screw rod 7.50 tonne capacity 4.00 M lift screw hoist having one number of EN-8 screw shaft, worm gear units having a lifting speed of around 5.00 cm/min for 24 rpm of hand operation including cost of all materials, labour, hire charges and conveyance. 1m Screw rod, dia 67mm with single start square thread with head pitch of 12.7mm, root dia 62.3mm EN -8 shaft |
| 239 | OD41559/2023-2024:THREAD LESS portion of the screw rod (per metre rate) |
| 240 | 85.112:Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350microns over the grit blasted and cleaned surface to class A standard of IS 14177 including cost of all materials , labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc complete as per the direction of departmental officer at site |
| 241 | 85.114:Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc on dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350 microns after cleaning the surface using hand and power tool cleaning including cost of all materials, labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site |
| 242 | 85.115:Cost of painting with 2 coats of enamel paint over 1 coat of zinchromate primer as per IS1477:1994 after hand and power tool cleaning including cost of all materials, labour charges, cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site |
| 243 | OD41567/2023-2024:Erection of the Canal Shutter ( Up to 2 Tonne weight ) / Hoisting bridge/ Platform including hand rails, ladder etc. for the same including alignment correcting and setting complete including cost of all labour, machinery, incidental and conveyance, lead and lift charges etc. complete but excluding cost of materials already supplied |
| 244 | 13.43.1:Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface:Water thinnable cement primer |
| 245 | 13.60.1:Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work |
| 246 | OD41564/2023-2024:SUPPLYING and APPLYING GREASE on NEW SCREW ROD for CANAL GATE |
| 247 | Scheme 10-Providing MS shutters, hoisting bridge and mechanism on Manamkulamp cross regulator, Kurissi and Chulannur off-take shutters.e shutters and cross regulators at LBC Malampuzha under Koduvayur Section. |
| 248 | OD41645/2023-2024:Taking out the mud debris and cleaning the bay, removing the plastic and bio waste and disposing at a suitable place 50m away from site |
| 249 | OD41649/2023-2024:Dismantling of the Canal Shutter ( Up to 2 Tonne weight )/ Hoisting unit, Embedded parts, etc. of the same and stacking at a distance of 100 metre including hire of machinery, labour etc. complete as directed by the departmental officer at site. (Weight of the unserviceable shutters and embedded parts may be calculated as 60% and unserviceable hoisting units as 80%) |
| 250 | 15.2.1:Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 251 | 5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete |
| 252 | 4.1.2:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:1/2:3 (cement : 11/2 coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 253 | 5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more |
| 254 | 5.2.2:Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up tot floor five level excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 255 | 13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) |
| 256 | OD41648/2023-2024:Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges |
| 257 | OD41647/2023-2024:Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges |
| 258 | OD41646/2023-2024:Supply of MS round bar including cost of conveyance charges |
| 259 | OD41650/2023-2024:SUPPLYING & STACKING of Dia 32 mm NB (1 1/4'') G.I. PIPE |
| 260 | OD41651/2023-2024:Supply of MS BOLT and NUT up to 300mm Length including cost of conveyance. |
| 261 | OD41652/2023-2024:Fabrication and erection of Embedded parts of Canal shutters ( Up to 2 tonne weight ) and accessories as per approved specifications, drawings and directions of deptl. officer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc. complete but excluding cost of material already supplied |
| 262 | OD41653/2023-2024:Fabrication, Supply, erection and assembling in correct position and alignment by welding SS Embedded parts in 304L Grade like roller track, seal track, Seal seat etc. as per approved specifications, drawings and directions of deptl. officer at site including cost of all materials, labour, machinery for planing, welding, shearing, grinding etc., lead and lift, conveyance, incidental and handling etc. complete |
| 263 | OD41654/2023-2024:Fabrication and supply of Structural steel Canal shutters ( Up to 2 tonne weight ) /Hoisting bridge/ Platform and accessories etc. as per approved specifications, drawings and directions of deptl. officer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc. complete but excluding cost of material already supplied |
| 264 | 85.116:Supplying and fixing in correct position with specified initial interface the flat type rubber seal confirming to IS 11855 to the gates including cost of SS bolts and nut all labour and machinery and incidental and conveyance charges complete as per approved specification and drawing |
| 265 | 85.118:Supplying and fixing in correct position with specified initial interface L-type / bulb nose rubber seal confirming to IS11855 to the gates including cost of SS bolts and nuts and all labour and machinery and incidental and conveyance charges complete as per approved specifications and drawings |
| 266 | OD41655/2023-2024:Providing of worm and pinion having a lifting speed of around 5.00 cm/min for hand operation including cost of all materials, labour, hire charges and conveyance. |
| 267 | OD41656/2023-2024:Providing EN-8 screw rod 7.50 tonne capacity 4.00 M lift screw hoist having one number of EN-8 screw shaft, worm gear units having a lifting speed of around 5.00 cm/min for 24 rpm of hand operation including cost of all materials, labour, hire charges and conveyance. 1m Screw rod, dia 67mm with single start square thread with head pitch of 12.7mm, root dia 62.3mm EN -8 shaft |
| 268 | OD41657/2023-2024:THREAD LESS portion of the screw rod (per metre rate) |
| 269 | OD41658/2023-2024:SUPPLYING and APPLYING GREASE on NEW SCREW ROD for CANAL GATE |
| 270 | 85.114:Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc on dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350 microns after cleaning the surface using hand and power tool cleaning including cost of all materials, labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site |
| 271 | OD41661/2023-2024:Erection of the Canal Shutter ( Up to 2 Tonne weight ) / Hoisting bridge/ Platform including hand rails, ladder etc. for the same including alignment correcting and setting complete including cost of all labour, machinery, incidental and conveyance, lead and lift charges etc. complete but excluding cost of materials already supplied |
| 272 | Scheme 11-Providing 3Nos of new SS Sluice shutters, extension channel and SS Cage Ladder at Malampuzha Dam LB canal Head Sluices. |
| 273 | OD41709/2023-2024:Providing with temporary platform for repair works of shutter and hoisting bridge including the cost of material charge, handling charge etc. complete (Temporary platform for 1 set) |
| 274 | OD41710/2023-2024:Dismantling the existing LBC sluice shutter and its accessories after erection of emergency shutter and stacking of these items at proper places as per the direction of deptl : officers at site by using chain blocks and derrick crane including cost of all materials, labor charges etc. complete. |
| 275 | OD41713/2023-2024:Lifting, Leading and Stacking the Hoisting Mechanism with Screw rod for sluice from the sluice well safely at a convenient place. |
| 276 | OD41712/2023-2024:Dismantling existing hoisting mechanism, platform, extension channel and its accessories and stacking of these items at proper places as per the direction of deptl : officers at site, including cost of all materials, labour charges etc. complete. |
| 277 | OD41851/2023-2024:Dismantling and Stacking the Existing all kind of rubber seals of Sluice Gate including cost of all materials, labour, hire charges etc. complete |
| 278 | 15.2.1:Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 279 | OD41714/2023-2024:DRILLING and FASTENING with TMT rod in concrete/Stone including conveyance and labor charges complete excluding cost of materials already supplied. |
| 280 | 4.1.2:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:1/2:3 (cement : 11/2 coarse sand : 3 graded stone aggregate 20 mm nominal size) |
| 281 | 85.101:Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges |
| 282 | 85.102:Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges |
| 283 | 85.107:Supply of MS round bar including cost of conveyance charges |
| 284 | OD41855/2023-2024:SUPPLYING & STACKING of Dia 25mm NB (1") G.I Pipe |
| 285 | OD41856/2023-2024:SUPPLYING & STACKING of Dia 32mm NB (1 1/4") G.I. PIPE. |
| 286 | 85.103:Supply of MS checquered plates including cost of conveyance charges |
| 287 | OD41854/2023-2024:Fabrication, Supply, erection and assembling in correct position and alignment by welding SS Embedded parts in 304L Grade like roller track, seal track, Seal seat etc. as per approved specifications, drawings and directions of deptl. officer at site including cost of all materials, labour, machinery for planing, welding, shearing, grinding etc., lead and lift, conveyance, incidental and handling etc. complete |
| 288 | OD41717/2023-2024:Fabrication and supply of Structural steel Sluice shutter / Operating platform / Extension Channel / Cage ladder and accessories etc. as per approved specifications, drawings and directions of deptl. officer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc. complete but excluding cost of material already supplied. |
| 289 | OD41847/2023-2024:Supplying and fixing Stainless steel thrust roller assembly having 300mm Dia, 90mm tread width, SS(304) shaft and 22316E self aligning spherical roller bearing and accessories as per approved specifications and drawings including cost of all materials, machineries, labour, all lift and lead, incidental and conveyance charges etc. complete |
| 290 | 85.116:Supplying and fixing in correct position with specified initial interface the flat type rubber seal confirming to IS 11855 to the gates including cost of SS bolts and nut all labour and machinery and incidental and conveyance charges complete as per approved specification and drawing |
| 291 | 85.118:Supplying and fixing in correct position with specified initial interface L-type / bulb nose rubber seal confirming to IS11855 to the gates including cost of SS bolts and nuts and all labour and machinery and incidental and conveyance charges complete as per approved specifications and drawings |
| 292 | OD41853/2023-2024:Supply and Stacking of Angular Bulb Nose rubber seal for corner (400mm X 400mm) |
| 293 | OD41857/2023-2024:Drilling and Fastening with Expansion Bolt M16x125mm length in concrete including conveyance and labor charges complete. |
| 294 | OD41863/2023-2024:LOADING and UNLOADING charges for materials. |
| 295 | OD41864/2023-2024:CONVEYANCE charge for materials. Data Observed for the conveyance for 100km (Enquired from market Rs.40 for one way hence Rs.80 for two way) |
| 296 | OD41865/2023-2024:HOT DIP GALVANISING the fabricated work piece to get a minimum coating thickness of 80 microns. (The work piece is to be caustic cleaned for removing impurities like grease, dirt etc. then it is pickled to remove oxides and is then given flux coating to prevent further oxidation and is then finally dipped in zinc bath). |
| 297 | OD41849/2023-2024:Erection of new extension channels and connecting with sluice shutter in proper alignment and correct position including hire charges of tools and plant, labour charges, industrial charges etc. complete. |
| 298 | OD41850/2023-2024:Erection of newly fabricated shutter from the dam top to sluice well bottom in proper alignment including hire charges of tools and plant, labour charges etc complete. |
| 299 | OD41859/2023-2024:Erection of the Canal Shutter ( Up to 2Tonne weight ) / Hoisting bridge / Platform including hand rails, ladder etc. for the same including alignment correcting and setting complete including cost of all labour, machinery, incidental and conveyance, lead and lift charges etc. complete but excluding cost of materials already supplied |
| 300 | 85.114:Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc on dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350 microns after cleaning the surface using hand and power tool cleaning including cost of all materials, labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site |
| 301 | OD41862/2023-2024:PAINTING with 2 coats of ALUMINIUM PAINT over 1 coat of ZINCHROMATE PRIMER as per IS1477:1994 after HAND and POWER TOOL cleaning including cost of all materials, labour charges, cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site. |
| 302 | OD41866/2023-2024:Leading, Lowering and Fixing the Hoisting Mechanism with Screw rod in correct alignment. |
| 303 | OD41867/2023-2024:Supplying and refilling Grade 320 gear oil for Hoisting mechanism of Sluice gates. |
| 304 | OD41869/2023-2024:Supplying and Applying Grease on Screw Rod of Sluice gate. |
| 305 | OD41870/2023-2024:Supply, fabrication, engraving and fixing of Stainless steel scale for measuring sluice gate vent height with reference to sill level |
| 306 | OD41861/2023-2024:Supply of Industrial safety belt, with double lanyard and scaffolding hook. |
| 307 | OD41860/2023-2024:Supply of Retractable Wire Rope Fall Arrester Block with galvanized steel cable of 20meter length, auto locking, swivel type snap hooks, 150Kg safe working load. |
| 308 | OD41871/2023-2024:Trial running of Regulator/Spillway/Sluice gates manually, including cost of all materials, labour charges etc. complete. Please Enable Macros to View BoQ information |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
