|
| 1 | Good Earth for filling un-even land [HSR 3.1.2 plus 17.8.2 plus 17.8.3] |
| 2 | (i) 6 No. Ornamental Design FRP pillar FRP base pedestal with vertical fitted design having base width of size 260mm x 260mm and height 900mm having 4 no. of size 15mm drilled in the base with hold fasts and having B class vertical m.s pipe of size 89 mm and height 2890mm, the central m.s pipe having FRP capital suitably mounted at appropriate height complete as per design enclosed. Complete pillar suitably grinded spray primered and subsequently spray painted with two coats of enamel paints is required shade. (ii) 12 No. spndred and 6 no. Friezes Floral and Ornate decorative design combination of spandrel and frieze, matched to be suspended between two m.s pillars as per the design copy enclosed. The spandrel (L-Bracker) having length 310mm and height 300mm the frieze (Top Panel) height 220mm and length as per the size of the gazebo. The frieze mounted on m.s tabular pipe frame of size 40mm x 25mm, frieze properly welded to the column pollars at either ends. Complete set of spandrel and frieze uniformly grinded spray primered, spray painted with two coats of enamel paint.(iii) 3 No. cast iron base panel railing with frame Floral and Ornate decorative design cast iron side railing panel as per design copy enclosed having height of 730mm and length as per size of Gazebo. Each panel top and bottom mounted with mild steel tubular pipe frame of size 40 x 25 mm. the bottom mild steel pipe having 3 nos. of hold fasts in m.s pipe of size 40 x 40mm and length 50mm welded at the base to hold the panel in the ground. The complete railing panel grinded for neat surface finishes spray primered and subsequently spray painted with two coats of enamel paint in required shade. (iv) One set of top frame with frp roof Top frame in m.s tubular pipe of size 40 x 40mm properly welded and grinded. The top frame mounted with FRP molded Sheet of 2 mm thick bent to profile on either ends with clear width installation of frp sheets fixed horizontally along the length between column pillars. Each sheet enamel painted in red color on both sides. Each such sheet properly riveted to horizontal sheets. The roof pipe frames properly primered and painted in red color. The complete item is without C.C floor and without sitting bench. rates are including with all taxes |
| 3 | Bridge Ladder: 10’L x 2’W x 6’H. Horizontal ladder is of m.s pipe 2” and ¾” and vertical ladder is of same material of 12 gauge ISI mark with suitable PU Primer and PU Paints. Complete item with GST, Transportation, Installation with C.C and labor at site. |
| 4 | Providing and fixing Chain Swing - 2 seater ( Swing). Specifications Attached. |
| 5 | merry go round 4 seater 5dia main frame is m s sq pipe round pipe centrel pipe which further pipe supports with pipe ball bearing assembly chair made of molded frp plastic pu primer and pu paints |
| 6 | Wave Slide: 9’.5 L x 5’H. Wave slide is of molded Fiberglass Reinforced Plastic (FRP) of 6mm thick and climbing ladder is of m.s pipe 1” x 12 gauge and m.s rectangular pipe |
| 7 | Arm Wheel/ Shoulder Wheel:- Providing, and fixing Arm Wheel in a pair of size 850 X 800 X 1800 mm make of Green Gym or Equivalent fabricated with main post of 140 mm dia and 3.0 mm thick rest of the pipes are 40 mm dia and 2.5 mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe |
| 8 | Air Swing: Providing designing and fixing air swing in pair of size 1150 x 900 x 1250 mm fabricated with main post of 114mm dia and 2.5mm thick and rest of the pipes 40mm dia and 2.5 mm thick. All pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber. Pedals shall be made up of Nylon alloy with rounded edges to prevent any impact or injury. Seats and base plate cover to be made up from virgin LLDPE manufactured by rotational |
| 9 | Leg Press: Providing designing and fixing of leg press of size 2000x550x1600 mm fabricated with main post of 114mm dia and 2.5mm thick and rest of the pipes 40mm dia and 2.5mm thick. All pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel or equivalent of 80-120 micror thick. |
| 10 | Knee HIP Raise:-Providing, and fixing Knee Hip Raise of size 1105 X 550 X 11480 mm make of Green Gym or Equivalent fabricated with main post of 140 rum din and 3.0 mm thick rest or the pipes are 40mm dia and 2.5 mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Mao Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped |
| 11 | Seated chest press: Providing designing and fixing of seated chest press in a pair of size 1800 x 700 x2000 mm fabricated with main post of 114mm dia and 2.5mm thick and rest of the pipes 40mm dia and 2.5 mm thick. All pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. |
| 12 | Double Cross Walker/ Cross trainer double:-Providing, and fixing Double Cross Walker of size 1600 X600 X 1600 mm make of Green Gym or Equivalent fabricated with main post of 140 mm dia and 3.0 mm thick rest of the pipes are 40 mm dia and 2.5 mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U Vresistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Officer -in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength N425 and J shaped welded bolts and once the concrete is set |
| 13 | NS Item = Supply of RH Pipe 1` dia. |
| 14 | Providing and fixing 25 mm id GI pipe with GI fitting |
| 15 | Providing and fixing 3/4`dia Hydrant connection |
| 16 | Providing and fixing of Gate valve for hydrant connection |
| 17 | Multiplay Single Station coveringArea: 13’L x 4’W It Contains: FRP Waveslide 6mm thick at 5’H-1no. FRP Square canopy 2mm thick-1no. FRP Platform 3’.5 x 3’.5 x 5mm thick-1no. M.S Vertical Station made of m.s pipe 2”.5 x 12G-1no. M.S Zig-Zag Climber-1no. M.S Climbing Ladder-1no. |
| 18 | -Horse Rider Station:- Providing, and fixing of horse rider station of size 1000 x600 x 1100 mm make of Green Gym or Equivalent fabricated with main post of 140 mm dia and 3.0 mm thick rest of the pipes are 40mm dia and 2.5 mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Alczo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer |
| 19 | `-``Twister:-Providing, and fixing Twister of size 1700 X 1300 X 1300 mmmake of Green Gym or Equivalent fabricated with main post of140 mm dia and 3.0 mm thick rest of the pipes are 40mm diaand 2.5 mm thick all pipes made up of hot rolled tubular steeland hot dipped galvanized, and powder coated using AkzoNobel or equivalent of 80-120 micron thick. All welding jointsof pipe are robotic welded with joints scalloped as necessaryand dressed off removing sharp edges and burrs. Zinc primerpaint to be applied at all welding points prior to finishing.Padals shall be made up of Nylon alloy with rounded edge ofprevent any impact of injury and seat to be made from virginLLDPE manufactured by rotational moulding with minimumthickness of plastic 4.00mm, colourful and U V resistantenvironmental friendly. Bearing used shall be maintenancefree, duly oiled sealed and self lubricated made by reputedcompany to be approved by Officer-in-Charge. Equipment to befitted within built limiters to prevent unwanted movements. Allopen ends of pipe to be coloured by GI/LLDPE caps for usersafety. The equipment to be fixed on ground with concrete ofminimum strength M25 and ishapod welded bolts and once theconcrete is set, fix the equipment on to it and cover nuts andbolts with the base plate cover, all complete as per direction andapproval of Officer -in-Charge regarding material, shape ofequipment, colour on metal, seat and base cover plate andfixing of. equipment etc.``` |
| 20 | Providing and Fixing mono block 1 HP motor Texmo make complete in all respect. |
| 21 | NS Item= Ornamental Canopy with base complete in all respect – with 6 No. Ornamental Design FRP Molded Pillar FRP base pedestal with vertical fitted design having base width of size 260mm x 260mm and height 900mm having 4 no. of size 20mm drilled in the base with hold fasts and having B class pipe of size 88 mm and height 2890mm, the central m.s pipe holds FRP Molded taj 6no of size 260 x 260 x 210mm high suitably mounted at appropriate height complete as per design. Complete pillar suitably grinded and subsequently spray painted with two coats of P.U Paints in required shade. (ii) 12 No. spndred and 6 no. Friezes Floral and Ornate decorative design combination of spandrel and frieze, matched to be suspended between two m.s pillars as per the design. The spandrel (L-Bracket) having length 420mm and height 400mm the frieze (Top Panel) height 250mm and length as per the size of the gazebo. The frieze mounted on m.s tabular pipe frame of size 50mm x 25mm, frieze properly welded to the column pillars at either ends. Complete set of spandrel and frieze uniformly grinded spray primered, spray painted with P.U Paints. (iii ) 3 No. cast iron/frp base panel railing with frame Floral and Ornate decorative design cast iron/frp side railing panel as per design having height of 730mm and length as per size of Gazebo. Each panel top and bottom mounted with mild steel tubular pipe frame of size 50 x 25 mm. The bottom mild steel pipe having 2 nos. of hold fasts in m.s pipe of size 40 x 40mm and length 250mm welded at the base to hold the panel in the ground. Every panel length is as per the gap between the two pillars. The complete railing panel grinded for neat surface finishes spray primered and subsequently spray painted with P.U Paint in required shade. (iv) One set of top frame with Double Finishing FRP Molded Plastic Sheet roof Top frame in m.s tubular pipe of size 40 x 40mm properly welded and grinded. The top frame mounted with FRP molded Sheet of 4 mm thick with top and bottom good finishing (Double finishing sheet) to make it rust proof bent to profile of size 245mm width in -Z- section on either ends fixed horizontally along the length between column pillars. Also it contain FRP Moulded Ball of 14”Dia x 2mm thick at the central top for its beautification. Each sheet enamel painted in red color. Each such sheet properly riveted to horizontal sheets. The complete item is fitting at site with installation and construction of canopy base should be made of earth work .15 m deep, Brick ballast .15 m depth,two steps of first class brick work 1:5 of 3.00 mX.30 mX.45 m and 3.00 m X.30 m X.60m, cement concerete on .10 height and finishing with checqurred tiles on the base and steps. (Including fixing at site and supervision and transportation and all type taxes) |
| 22 | Supply and installation of 25 mm thick EPDM Rubberised flooring of 2 layers laid on PCC base.Layer 1 of 19mm SBR Sub Base cast in situ, Layer 2 of 6 mm EPDM Granules cast in situ ( Dow/ BASF binder tobe used for 6mm EPDM) . One year maintenance and warranty.As per approved pattern and colors, all works complete upto satisfaction of engineer incharge. Including 18% GST. |
| 23 | Providing And Installation Of Kids Play Equipment -Jungle GymAREA : 25 X 18 X 12 FEETAGE GROUP : 3-12 YRSCAPACITY : 3-10“A” Class ISI marked MS Pipe of Reputed Brand (Jindal, Apollo, Bharat Etc).Frp items – 2 wave slide , 2 frp roof , 1 frp tunnel , and all base with frp chequered (non-slippery), 1 fish attached to climber.SWING SEAT : RUBBER TYPE MAKE IN INDIAFRP Thickness between 3 To 8 mm.PU Coated Paint finish on the MS Structure.As Per Approved Design, including fixing In Ground With cement concrete at specifiedlocation till the satisfaction Of Engineer InchargeIncluding GST and other Charges. |
| 24 | Rowing machine: Providing designing and fixing rowing machine of size 1280x800x1150 mm fabricated with main past of 114 mm dia and 2.5mm thick and rest of the pipes 40mm dia and 2.5 mm thick. All pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber Foothold shall be made up of nylon alloy with rounded edges to prevent any impact or injury and base cover to be made up from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic as 3mm colourful and UV resistant and environmental friendly. Bearing used shall be maintenance free duly oil sealed and self lubricated made by reputed company to be approved by Engineer in charge. Equipments to be fitted with inbuilt limiters to |
| 25 | Description of Fountain in Dholpur stone (Red Stone) of size 12` dia complete in all respect. Plate (Down) 1. 5`-0`x5`-0`x12`-0` 2. 48`x48`x12` 3. 36`x36`x10` 4.24`x24`x7` Rutter (Down) Under Plate 1.20`x20`x36` 2. 15`x15`x20` 3. 13`x13`x18` 4. 12`x2`15` 5. 10`x10`x15` 12` dia out side boundary of fountain with Dholpur outside and top and 1st quality ceramic glazed wall tiles in side. Including 1 HP Motor, water connection, electricity connection Market Rate plus GST plus Transpotation, Labour for fixing plus 10% Contractor Profit complete in all aspect. |
| 26 | Estimate for renovation of Park green belts near B27, E1B, E21, Block-CandE Round Park and D14/21 Ardee City Sector-52 ward 21, MCG. Please Enable Macros to View BoQ information |
