Tender For Construction Of Sp Office At East Bank Of Jagannath Dighi At Udaipur , Gomati Tripura Including Water Supply, Sanitary Installation And Internal Electrical Installation. (Balance Part)., Udaipur-Tripura

TDR : 54545999

Tender Notice
BOQ

Expired

Udaipur , Tripura

Tender Brief : Tender For Construction Of Sp Office At East Bank Of Jagannath Dighi At Udaipur , Gomati Tripura Including Water Supply, Sanitary Installation And Internal Electrical Installation. (Balance Part).

Document Fees
₹ 15000 /-

EMD
₹ 2132540.0 /-

Tender Value
₹ 10.66 Crore /-

Submission Date
23-03-2026

Competition Type
Indian

Bidding Type
Tender

Need a Business Loan? Apply Now !


1	(A) S.H. EARTH WORK Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed - All kinds of soil
2	Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. -All kinds of soil
3	Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. -All kinds of soil
4	Supplying and filling in plinth, under floor, foundations etc. With sand (fine) from local quarry with all lifts including spreading in horizontal layers, watering, grading to required slope, ramming, consolidating and compacting each layer by using plate compactor or by any suitable method complete.
5	Supplying chemical emulsion in sealed containers including delivery as specified. (i) Chlorpyriphos/Lindane emulsifiable concentrate of 20%
6	Treatment of soil under plinth filling using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with sand filling:(i) With Chlorpyriphos/Lindane E.C. 20% with 1% concentration
7	(B) S.H. CONCRETE WORK Providing and Laying in position cement concrete of specified grade excluding the cost of centring and shuttering- (A). All work upto plinth level: (i) 1:4: 8 (1 cement :4 fine sand : 8 graded well burnt brick aggregate 40 mm nominal size).
8	(ii) 1:3:6 ( 1 Cement: 3 fine sand : 6 graded well burnt brick aggregate 40 mm nominal size)
9	(C) S.H. PILE WORK Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by percussion drilling using Direct Mud Circulation (DMC) or Bailer and Chisel Technique by Tripod and Mechanical Winch Machine all complete, including removal of excavated earth with all its lifts and leads. (Length of pile for payment shall be measured upto bottom of pile cap). Note: Truck Mounted rotary / TMR / Tubewell Boring Machine shall not be used. i) 450 mm dia piles.
10	Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer incharge:- Note: 1. Initial and Routine Load Test shall not be carried out by Dynamic Method of TestingNote: 2. Testing agency shall submit the design of loading platform for the approval of Engineer-in-Charge. (A) Single pile above 50 tonne and upto 100 tonne safe capacity pile:- (i) Routine test (Test Load 1.5 times the safe Capacity).
11	(B) Group of two or more piles upto 50 tonne safe capacity (i) Routine test (Test Load 1.5 times the safe Capacity).
12	Providing and laying dry flat brick flooring in required pattern complete.
13	(D) S.H. REINFORCED CEMENT CONCRETE WORK Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centring, shuttering, finishing and reinforcement. -All work upto plinth level:(i) 1:1:2 ( 1 Cement: 1 fine sand : 2 graded stone aggregate 20 mm nominal size)
14	ii) 1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size)
15	Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto floor five level excluding the cost of centring, shuttering, finishing and reinforcement- (i) 1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size)
16	Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and skirting courses, fillets, columns, pillars, piers, abutments, posts and struts etc. upto floor five level excluding cost of centring, shuttering, finishing and reinforcement- (i) 1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size )
17	Reinforced cement concrete work in vertical and horizontal fins individually or forming box louvers, facias and eaves boards above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with (i) 1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size).
18	Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. (i) Thermo-Mechanically Treated bars of grade Fe-500D or more.
19	Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. (i) Thermo-Mechanically Treated bars of grade Fe-500D or more.
20	Centering shuttering including struttings, propping etc. and removal of form work for: (i) Foundations, footings, bases for columns etc. for mass concrete with timber plank
21	ii) Suspended floors, roofs, landings, balconies and access platform with timber plank.
22	iii) Suspended floors, roofs, landings, balconies and access platform with 12 mm thick shuttering ply
23	iv) Weather shade, Chajjas, corbels etc., including edges.
24	v) Lintels, beams, plinth beams, girders, bressumers and cantilevers with wooden plank
25	vi) Lintels, beams, plinth beams, girders, bressumers and cantilevers with shuttering ply
26	vii) Columns, Pillars, Piers, Abutments, Posts and Struts with wooden plank
27	viii) Columns, Pillars, Piers, Abutments, Posts and Struts with shuttering ply
28	ix) Stairs (excluding landings) except spiral-staircases with wooden plank
29	x) Vertical and horizontal fins individually or forming box louvers band, facias and eaves boards
30	xi) Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. using shuttering ply
31	(E) S.H. BRICK WORK First class brick work in foundation and plinth including cost of all materials as required complete: (i) In cement mortar 1:6 ( 1 cement : 6 fine sand )
32	First class brick work in superstructure above plinth level & upto floor-five level including cost of all materials as required complete:- (i) In cement mortar 1:6 ( 1 cement : 6 fine sand ).
33	Half brick masonry work with first class bricks in foundation and plinth including cost of all materials as required complete: (i) In cement mortar 1:4 ( 1 cement : 4 fine sand ).
34	Half brick masonry work with first class bricks in superstructure upto floor five level including cost of all materials as required complete:- (i) In cement mortar 1:4 ( 1 cement : 4 fine sand ).
35	(F)S.H: ALUMINIUM WORK Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixing with dash fasteners of required dia and size, including necessary filling up of gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawing and the direction of Engineerincharge. (Glazing and paneling and dash fasteners to be paid for separately) : (A) For fixed portion of approved quality:- (i) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15).
36	(B) For shutters/ sliding shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing fittings wherever required including the cost of EPDM rubber/ neoprene gasket required ( Fittings shall be paid for separately ):- (i) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15).
37	Providing and fixing glazing of approved quality in aluminium doors, windows, ventilator, shutters and partition frames with EPDM rubber/ neoprene gasket etc. complete as per architectural drawing and the direction of Engineer-in-charge :-(Cost of snap beading shall be paid in basic item.) (i) With float glass panes of 4.0 mm thickness ( weight not less than 10.0 kg / sqm )
38	(G)S.H: STEEL, WOOD & PVC WORK Providing and fixing T-iron frames for doors, windows and ventilators of mild steel Tee-sections, joints mitred and welded, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer. i) Fixing with 15x3 mm lugs 10cm long embedded in cement concrete blocks 15x10x10 cm of 1:3:6 (1 cement : 3 river sand : 6 graded stone aggregate 20 mm nominal size)
39	Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veeners on both faces of shutters. (i)35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws.
40	Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : (i)4.0 mm thick glass panes
41	Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. all complete. (i) Fixed to openings /wooden frames with rawl plugs screws etc.
42	Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).
43	Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2mm at 100 mm centre to centre and braced with flat iron diagonals 20x5mm size with top and bottom rail of T-iron 40x40x6mm with 40mm dia. steel pulleys & with riveted bolts, nuts, locking arrangement, stoppers, handles, hold fast /anchor bolt including embedding in cement concrete of required grade for fixing in position, all necessary fittings, including applying a priming coat of approved steel primer etc. complete as required.
44	Supplying and fixing rolling shutters of approved make, made of required size M.S. laths interlocked together through their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete including the cost of providing and fixing necessary 275mm long wire springs grade No.2 and M.S. top cover of required thickness for rolling shutters & with handles, hold fast including embedding in cement concrete of required grade required for fixing in position, all necessary fittings, including applying of approved steel primer etc. complete as required:- (i) 80xl.25mm M.S. laths with 1.25 mm thick top cover
45	Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.
46	Providing and fixing chromium plated brass handles with necessary screws etc. complete: (i) 125 mm
47	ii) 75 mm
48	Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete : (i) 300x10 mm
49	ii) 100x10 mm
50	Providing and fixing ISI marked oxidised M.S.sliding door bolts with nuts and screws etc. complete (i) 300×16 mm
51	Providing and fixing fan clamp type-I of 16 mm dia M.S. bar bent to shape with hooked ends in R.C.C. slabs during laying including painting the exposed portion of loop, all as per standard design complete.
52	Providing and fixing factory made door frame (single rebate) made of solid PVC foam profile with homogenous fine cellular structure having smooth outer integral skin having 60mm width & 30mm thickness and shall be fixed to wall as per instructions of Engineer-In-Charge using 100x8 sheet metal CSK screws.
53	Providing and fixing 28 mm thick door shutter made of solid PVC foam profile with homogenous fine cellular structure having smooth outer integral skin having 71mm width & 28mm thick as vertical & horizontal styles. Joints are made using solvent adhesive and GI ‘C sections (39mm x 19mm x 0.6mm thick) or M S pipe (40mm x 20mm ) stiffener frame insert & telescopic polymeric ‘L’ corners .The panel shall be filled with 3mm thick high - pressure compact laminate as per manufacturer’s specifications and directions of the Engineer-in-charge, cover moulding shall be provided for covering fixing screws and elegant look.( for W.C. bathroom door shutter).
54	(H) S.H. FLOORING WORK Providing and fixing Kota stone in floors over 20 mm thick bed of cement mortar 1 : 4 ( 1 cement : 4 fine sand) jointed with ordinary cement slurry including pointing with ordinary cement mixed with pigment of matching shade, including rubbing and polishing etc. all completeas per direction of Engineer-in-charge. (i)Kota stone slab 25mm thick
55	Providing and laying 1st class quality vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and, conforming to IS: 15622 - 2017of approved make, in all colours and shades, laid over 20mm thick cement mortar 1:4 (1 cement : 4 fine sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc. all complete as per direction of the Engineer-in-charge..(A)Double charged Stainfree vitrified tiles (Glossy)(i) Size of tile 600 mm x 600 mm (i)300 mm x 300 mm in all shades and designs
56	Providing and laying 1st class quality ceramic floor tiles in different sizes (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 - 2017 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid over 20 mm thick cement mortar 1:4 (1 cement : 4 fine sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc. all complete as per direction of the Engineer in-charge.Mat Finish Tiles/ Anti-skid Tiles/ Glossy Tiles. (i)300 mm x 300 mm in all shades and designs
57	Providing and fixing Marble stone in floors over 20 mmthick bed of cement mortar 1 : 4 ( 1 cement : 4 fine sand) jointed with ordinary cement slurry including pointing with white cement mixed with of matching shade, including rubbing and polishing etc. all complete as per direction of Engineer-in-charge. (i)14 mm thick Marble stone (i) Raj Nagar plain marble
58	Providing and fixing chequered terrazo tiles 22 mm thick with graded marble chips of size upto 6 mm, laid on floors, footpath & courtyard on 20 mm thick bed of cement mortar 1 : 4 ( 1 cement : 4 fine sand ) jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and polishing etc. all complete as per direction of Engineer-in-charge. (i) Dark shade pigment using ordinary cement
59	Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622 ( thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1 : 3 ( 1 cement : 3 fine sand ) jointed with ordinary cement slurry including pointing with white cement mixed with pigment of matching shade complete. i)450 mm X 300 mm in all shades and design
60	Providing and laying factory made chamfered edge cement concrete paver block of required strenght thickness and size shape made by table vibratory method to attain superior smooth finish using PU or equivalent moulds laid in required grey color and pattern over and including 50 mm thick compacted bed of sand, compacting and and proper embedding / laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator , filling the joints with fine sand and cutting of paver blocks as per required size and pattern finishing and sweeping extra sand in footpath, parks lawns drive ways or light traffic , parking etc all complete as per specification & approval / direction of Er in charge.(a) 60 mm thick C.C. paver block of M-35 grade with approved color design and pattern.
61	(I) S.H. FINISHING WORK 12 mm cement plaster of mix(i) In cement mortar 1 : 6 ( 1 cement : 6 fine sand )
62	15 mm cement plaster on the rough side of single or half brick wall of mix:(i) In cement mortar 1 : 6 ( 1 cement : 6 fine sand )
63	6 mm cement plaster of mix : (i) Cement mortar 1:3 (1 cement : 3 fine sand)
64	12 mm cement plaster of mix(i) In cement mortar 1 : 4 ( 1 cement : 4 fine sand )
65	Neat cement punning.
66	Finishing walls with acrylic smooth exterior paint of required shade of approved brand and manufacture [Payment shall be made after submission of Test Certificate issued by the Manufacturer] : (i)New work ( two or more coats applied @ 1.67 litre/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)
67	Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.
68	Wall painting with acrylic plastic emulsion paint of approved brand and manufacture to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer] : (i)Two or more coats on new work
69	Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 grams/ litre, of approved brand and manufacture, of required shade and colour complete, as per manufacurer's specification. [Payment shall be made after submission of Test Certificate issued by the Manufacturer]. i)Two or more coats on new work.
70	Applying priming coat [Payment shall be made after submission of Test Certificate issued by the Manufacturer] : (i) With ready mixed Pink or Grey primer of approved brand and manufacture on wood work ( hard & soft wood ).
71	ii)With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/steel works.
72	Painting with synthetic enamel paint of approved brand and manufacture to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer]: (i)Two or more coats on new work
73	(J) S.H. WATER PROOFING WORK Grading roof for water proofing treatment complete as required as per direction of the Engineer-in-charge with : (i) Cement concrete 1:2:4 (1 cement : 2 fine sand : 4 graded stone aggregate 20 mm nominal size)
74	(K) S.H. SANITARY INSTALLATION AND WATER SUPPLY WORK Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : (i) White Vitreous china Orrisa pattern W.C. pan of size 580x440 mm with integral type foot rests.
75	Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : (i) W.C. pan with ISI marked white solid plastic seat and lid
76	Providing and Fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 340x410x265mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :One urinal basin with 5 litre white P.V.C. automatic flushing cistern.
77	Providing and fixing white vitreous china squatting plate urinal with integral rim longitudinal flush pipe.
78	Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require : (i) White Vitreous China Flat back wash basin size 550x400 mm with single 15 mm C.P. brass pillar tap
79	Providing and fixing toilet paper holder : C.P. brass
80	Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings.
81	Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug 40mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete including painting of fittings and brackets, cutting and making good the wall wherever required :Size 450x300x150mm
82	Providing and fixing C.P. brass shower rose with 15 or 20 mm inlet: 100 mm diameter
83	Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. (A) Semi rigid pipe (i) 32 mm dia
84	Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.
85	Providing and fixing 600x120x5mm glass shelf with edges round of supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.
86	Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved 450mm long towel rail with total length of 495mm, 78mm wide and effective height quality and colour. (i) 600mm long towel rail with total length of 645mm, width 78mm and effective height of 88mm, weighing not less than 190gms.
87	Providing and fixing on wall face unplasticised Rigid PVC soil, waste & vent pipes (working pressure 6 kg / cm2) conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion: i) Single socketed pipe - 110 mm OD
88	Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC soil, waste & vent pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing with cement mortar 1 : 4 (1cement : 4 fine sand) making good the wall etc. complete. (i) 110mm
89	Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC soil, waste & vent pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion: (i) Coupler-110mm
90	ii)Single equal tee without door -110x110x110mm
91	iii)Single equal tee with door-110x110x110mm
92	iv)Bend 87.5° -110mm
93	v)Terminal guard -110 mm
94	Providing and fixing to the inlet mouth of soil, waste & vent pipes pipe PTMT grating with thickness of 8mm and weighing not less than 100gm. complete.-i)100 mm
95	Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. (i) 15 mm nominal bore.
96	Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 (i) 15 mm nominal bore
97	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cementand testing of joints complete as per direction of Engineer in Charge.Internal work - Exposed on wall (i) 15 mm nominal outer dia .Pipes.
98	ii) 20 mm nominal outer dia .Pipes.
99	iii) 25 mm nominal outer dia .Pipes.
100	Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement trenching ,refilling & testing of joints complete as per direction of Engineer in Charge. External Work (i) 25 mm nominal outer dia .Pipes.
101	ii) 32 mm dia. nominal outer dia .Pipes.
102	iii) 40 mm dia. nominal outer dia .Pipes.
103	Providing and fixing brass stop cock of approved quality : (i) 15 mm nominal bore
104	ii) 20 mm nominal bore
105	Providing and fixing uplasticised PVC connection pipe with brass unions : (A) 45 cm length (i) 15 mm nominal bore
106	Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.
107	Providing and fixing on wall face unplasticised Rigid PVC rain water pipes (working pressure 4 kg/cm2) conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion etc. complete as per direction of Engineer-in-charge :Single socketed pipe - 110 mm OD
108	Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type-A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion etc. complete as per direction of Engineer-in-charge : (i)Coupler-110 mm
109	Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing with cement mortar 1 : 4 (1cement : 4 fine sand) making good the wall etc. complete as per direction of Engineer-in-charge.i)110mm
110	Providing and fixing to the inlet mouth of rain water pipe PTMT grating with thickness of 8mm and weighing not less than 100gm. etc. complete as per direction of Engineer-in-charge. (i) 100 mm
111	(L) S.H. DEEP TUBEWELL Drilling and boring pilot hole in any soil strata by manual means, collection of soil samples of different strata met with during drilling at various suitable levels, preservation of samples in polythene bags / sample boxes and disposal of excess soil or mud, including the cost for water etc. as required to maintain the pilot hole properly as per specification and direction of the Engineer - in - charge. (i) 100 mm
112	Reaming of pilot hole to an enlarged bore hole in any soil strata bby manual means, disposal of excess soil or mud, including the cost for water etc. As required to maintain the bore hole properly as per specification and direction of the Engineer-in-charge. i) from 100 mm dia pilot hole to 250 mm bore hole
113	Washing and development of tube well by using hand pump or by any suitable method and testing of the well as per specification and direction of the Engineer-in-charge.
114	Providing & lowering of UPVC pipe as per IS:12818 after washing of the bore hole by manual means as per specification and direction of the Engineer-in-charge.UPVC CM Casing pipe (i) 150 mm dia
115	UPVC RS Pipe (i) 150 mm dia
116	UPVC RS Pipe (i) 100 mm dia
117	Providing fixing of UPVC end cap / well suitable for UPVC 'CM' casing or 'CS' casing or 'RS' pipes as per specification and direction of the Engineer in charge.
118	Providing and shrounding of the deep tube well assembly with washed pea gravels ( 2.0 - 4.75 mm effective size ) as per specification ( IS : 4097) and direction of the Engineer-in-charge. With Contractor's rig i) Pea gravels obtained deom Durgapur, West Bengal.
119	Providing and fitting fixing with PVC insulated 3 core flat Copper cable conforming to relevant IS code for submerssible motor with all necessary equipments and fittings as required as per specification and direction of the Engineer-in-charge.i) 2.5 Sqmm
120	Providing and fixing G.I bend / elbow in the pipe line including testing of joints complete as per CPWD specification and direction of the Engineer in charge. (a) 40 mm dia
121	Supplying and fitting fixing of single phase motor starter panel unit 5 HP capacity comprising with 2 pole conductor , over load relay capacitor , voltsmeter of ISI marked (Havells or equivalent) with necessary copper wire etc complete as per direction of engineer in charge.
122	Supplying & installation of water libricated Submersible pump having ISI marked capacity 1000 GPH at total head upto 60mtr cuple with submersible motor 5 HP (Havells or equivalent) suitable for 220 voltas (+105 variation single phase 50HP AC supply DOL starting method to run at 2790 RPM along with 35 mtr 2.5 Sqm cables including fitting fixing and lowering it with 40 mm dia G.I pipe upto 100 Ft (30.00 mtr) etc complete as per direction of the Engg In Charge .(40 mm GI pipe and fittings will be paid separately).
123	(M) S.H. INTERNAL ELECTRICAL INSTALLATION: Wiring for light/ fan/ exhaust fan/ call bell point with 2x1.5 sq. mm PVC insulated copper conductor cable (FR) in PVC conduit (medium gauge) recessed in slab/ wall complete with 6/10 amps modular type switch, cover plate, GI box, cover all openings with bakelite sheet including necessary connection etc. as required.
124	Wiring for 2 way controlling light point with 3x1.5 sq. mm PVC insulated copper conductor cable (FR) in PVC conduit (medium gauge) recessed in slab/ wall complete with 6/10 amps modular type 2 way switch, cover plate, GI box including necessary connection etc. as required.
125	Providing and fixing of 3 pin 6/10 amps plug point with modular type 6/10 amps switch and socket including connection with 2 x 1.5 sq. mm PVC insulated Copper conductor cable (FR) on modular concealed switch board with cover plate,earthing the 3rd pin,cover all openings with bakelite sheet etc. as required.
126	Providing and fixing of 3/6 pin 16/20 amps plug point with modular type 16/20 amps switch and socket including connection with 2 x 2.5 sq. mm PVC insulated Copper conductor cable (FR) on modular concealed switch board with cover plate earthing the 3rd pin, cover all openings with bakelite sheet etc. as required.
127	Wiring for Circuit/Sub-main with the following sizes PVC insulated Copper conductor cable (FR) in PVC conduit (medium gauge) recessed in slab/ wall etc. as required:- (i) 2 X 1.5 + 1 X 1.5 sq mm
128	(ii) 2 X 2.5 + 1 X 1.5 sq mm
129	(iii) 2 X 4 + 1 X 1.5 sq mm
130	(iv) 4 X 4 + 2 X 1.5 sq mm
131	(v) 4 X 6 + 2 X 2.5 sq mm
132	(vi) 4 X 10 + 2 X 4 sq mm
133	(vii) 4 X 16 + 2 X 6 sq mm
134	Wiring for Circuit/Sub-main with the following sizes of PVC insulated Copper conductor cable (FR) in existing PVC casing capping/ conduit in recess/surface including connection etc. as required:- (i) 2 X 1.5 sq mm
135	(ii) 2 X 2.5 sq mm
136	(iii) 2 X 4 sq mm
137	(iv) 4 X 70 sq mm
138	(v) 1 X 6 sq mm
139	MAIN PANEL/ SWITCH GEARS:- Supplying and installation of powder coated steel sheet enclosure (MCB DB) suitable for 240/415 volts MCB/Isolator/RCCB (SP/SPN/DP/TP/TPN/FP) complete with necessary bus bar, neutral link, din rail, earth bar i/c connection in recessed manner,cover all openings with bakelite sheet etc as required. (a)4 way vertical TPN MCB DB suitable for FP MCCB incomer upto 250 amps (Double door):-
140	(b) 6 way vertical TPN MCB DB suitable for FP MCCB incomer upto 125 amps (Double door):-
141	(c) 4 way vertical TPN MCB DB suitable for FP MCB incomer (Double door):-
142	(d) 6 way horizontal TPN MCB DB (Double door):-
143	(e) 8 way horizontal TPN MCB DB (Double door):-
144	(f) 4 way horizontal TPN MCB DB (Double door):-
145	(g) (2+10) / 12 way SPN MCB DB (double door):-
146	(h) (2+6) / 8 way SPN MCB DB (double door):-
147	(i) 4 way SPN MCB DB (double door):-
148	(j) 2 way SPN MCB DB (single door):-
149	Supplying & installation of TP/FP MCCB of following ratings in the existing MCCB enclosure/ panel board including connection etc as required (Ics=100% of Icu with adjustable settings):- (i) 16 to 100 amps FP MCCB, Breaking capacity 16/18KA (Thermal Magnetic):-
150	(ii) 200 amps FP MCCB, Breaking capacity 25KA (Thermal Magnetic) :-
151	Supplying, installation, testing & commissioning of powder coated prewired digital meter module complete with ammeter, voltmeter, phase indicator lamp, control fuses, CTs, in the CRCA made board including connection etc. as required:-
152	Supplying & installation of 10 KA breaking capacity, B/C curve MCB of following ratings in the existing MCB DB including connection as required:- (i) 6 to 32 amps SP MCB:-
153	(ii) 6 to 32 amps DP MCB:-
154	(iii) 6 to 32 amps TP MCB:-
155	(iv) 6 to 32 amps FP MCB:-
156	(v) 40/50/63 amps TP MCB:-
157	(vi) 40/50/63 amps FP MCB:-
158	Supplying and installation of Switch disconnector fuse unit (main switch) of the following ratings with all accessories including necessary connection etc. as required:- (i) 200 amps 415 volts TPN main switch (rewireable):-
159	Supplying & installation of RCCB (sensitivity 30mA to 300mA) of following ratings in the existing MCB DB including connection etc as required:- (i) 25 to 40 amps FP RCCB:-(30mA )
160	(ii) 63 amps FP RCCB:- (ACDB 100 mA)
161	(iii) 16 to 40 amps DP RCCB:-(30mA )
162	Supplying & installation of Surge Protection Device (SPD) of following ratings in the existing Panels/MCB DBs including necessay connections etc as required:- (i) Surge Protection Device (SPD, withdrawable) (Type-2) with Imax 40 KA (3P+N) :-
163	(ii) Catridge for Surge Protection Device (SPD) (Type-2) with Imax 40 KA (3P+N) :-
164	LIGHTS FITTINGS :- Supplying and fixing of following surface/recess mounted LED luminaries in powder coated die cast housing complete with high efficiency polycarbonate diffuser and necessary connection ,cover all openings with bakelite sheet etc. as required (with 50000 burning hours and minimum lumen output of 100 lm/watt):- (i) Surface mounted box type batten suitable for single 18/20 watt integrated LED tube lamp (without lamp):-
165	(ii) Recessed/Surface mounted 4ft x 1ft decorative 30/36 watt LED panel light with integral driver and high quality polycarbonate diffuser:-
166	(iii) Recessed/Surface mounted 2ft x 2ft decorative 36 watt LED panel light with integral driver and high quality polycarbonate diffuser:-
167	(iv) Surface mounted round/Square shaped 12 watt LED downlight with integral driver and high quality polycarbonate diffuser:-
168	(v) Recessed round/Square shaped 12 watt LED downlight with integral driver and high quality polycarbonate diffuser:-
169	(vi) Surface mounted round/Square shaped 6/7 watt LED downlight with integral driver and high quality polycarbonate diffuser:-
170	(vii) Surface mounted round/Square shaped 18/20 watt LED downlight with integral driver and high quality polycarbonate diffuser:-
171	Supplying and fixing of following outdoor LED luminaries in powder coated die cast housing complete with heat resistant tempered glass/diffuser including necessary connection etc. as required (50000 burning hours and minimum lumen output of 100 lm/watt):- (i) 90 watt LED street light fixture with integral driver and secondary lens (IP 66):-
172	(ii) 40 watt LED post top light fixture with integral driver and high quality polycarbonate diffuser (IP 65):-
173	(iii) 120 watt LED flood light fixture with integral driver and secondary lens (IP 66):-
174	Decorative wall mounting fancy bracket light fixture suitable for GLS or retrofit CFL/LED (without lamp) :
175	Supplying and fixing of following LED Tubes, retrofit bulbs/lamps for LED luminaries including necessary connection etc. as required:- (i) 18/20 watt LED tube with integral driver and polycarbonate diffuser (50000 burning hours and minimum lumen output of 100 lm/watt):-
176	(ii) 12 watt LED retrofit lamp with polycarbonate body and aluminium heatsink :-
177	(iii) 20 watt LED retrofit lamp with polycarbonate body and aluminium heatsink :-
178	CEILING /EXHAUST FANS Supplying & fixing of 1200 mm sweep white color AC ceiling fan with brush less dirrect current (BLDC) motor having class B insulation, power factor not less than 0.9 complete with 300 mm down rod, canopies, shackle kit, 3nos blades, safety rope including wiring the down rod with 2x1.5 sqmm PVC insulated copper conductor cable(FR) (BEE 5 star/minimum service value 6.0 m3/min/W & tolerance as per IS:374-2019) : -
179	Supplying & fixing of 1400 mm sweep white color AC ceiling fan capacitor type double ball bearing complete with 300 mm down rod,canopies,shackles, 3nos blades, including wiring the down rod with 2x1.5 sqmm PVC insulated Copper conductor cable(FR) (ISI marked) : -
180	Supplying & installation of 225/230 mm sweep metalic body exhaust fan including connection etc as required:-
181	Supplying & installation of 300 mm sweep 900 rpm metalic body exhaust fan including connection etc as required (ISI marked) :-
182	Supplying & installation of shutter for 225/230/300 mm sweep metalic body exhaust fan in the existing hole as required:-
183	Making different sizes of hole in the wall for fixing of exhaust fan including finishing the same with cement plastering and painting etc as required:
184	EARTHING & LIGHTNING PROTECTION Earthing with 40 mm dia G.I. Earth pipe (medium gauge) 4.5 m. long complete with masonry enclosure on top CI cover plate size 12\\"x 12\\" having locking arrangement including CC work, holes on earth pipe etc. as required.
185	Extra for using salt (5 kg) and charcoal (46kg) for pipe earth electrode as required.
186	Proving and fixing / drawing of 4.06 mm dia (8 SWG) G.I. wire on surface or in existing G.I/ PVC/ Polythene pipe for loop earthing as required.
187	Supply and fixing of the following sizes GI /Copper prong with necessary nuts & bolts etc as required grouted on roof for Lightning protection. Copper. Prong 1000 mm long
188	Supply and fixing of 25mm x 3mm Copper on walls/ floor of the building for horizontal/ vertical network including necessary spacers and porcelain insulators at regular intervals.
189	Providng and laying 15mm dia(medium gauge) G.I. pipe for drawing of 4.06mm (8SWG) dia G.I./ Copper wire for earth connection from earth electrodes etc as required.
190	CC CAMERA :- SITC of 5MP IR Bullet Camera as per following specification• 1/2.8” SONY - CMOS (STARVIS Series) • 5MP, 0Lux with IR LED on, 2.8mm • IR Range of up to 50 meters • Video Analytics: Trip Wire, Intrusion Detection and Motion Detection,• H.265/H.264/M-JPEG Video Compression, BIS, CE, FCC, RoHS, IK10, IP67, UL, NEMA 4X.• PoE Support, NAS Storage, SD Card(512GB), Quad Stream Support,1/1 Audio I/O, 1/1 Alarm I/O • True WDR, 3D Noise Reduction, Adaptive Streaming, Smart Streaming and ROI, SNR > 70 dB • ER Compliant & Cyber Secured as per ISO / IEC 27402, NDAA Compliant, STQC cretified. make: Matrix/Panasonic/Bosch
191	SITC of 5MP IR Dome Camera as per following specification• 1/2.8” SONY - CMOS (STARVIS Series)• 5MP, 0Lux with IR LED ON.• IR Range of up to 30 meters.• Video Analytics: Motion Detection, Tamper Detection, Intrusion Detection, Tripwire• H.265/H.264/MJPEG Video Compression, BIS, CE, FCC, RoHS, IP67.• NAS Storage, Quad Stream Support• True WDR, 3D Noise Reduction, Adaptive Streaming, Smart Streaming and ROI, SNR > 70 dB• ER Compliant & Cyber Secured as per ISO / IEC 27402, NDAA Compliant, STQC cretified. make: Matrix/Panasonic/Bosch
192	SITC of 64 Channel NVR with 4K Support as per following specification.• 64 IP Channel Inputs; 4K HDMI, 1/1 Audio I/O and 2/1 Alarm I/O.• 12MP, 8MP, 5MP, 4MP, 3MP, 2MP, 720p, D1 and CIF Recording Resolution• 4x 4K/ 10x 3MP/16x 1080p Local Decoding• 8 SATA HDD Support (Maximum 18TB Capacity per Slot, Hard Disk Not Included)• Save Storage Space with Adaptive Recording and Camera-wise Recording Retention • SMS & Email Notification, Video Pop-up, Alarms and Instant Calling from Mobile Application as compitable.• Throughput - 512Mbps Uplink, 512Mbps Downlink, ONVIF and support for other camera brands.make: Matrix/Panasonic/Bosch
193	SITC of Display ,Screen Size 43 Inches as per following specification. Resolution: Technology LED, 4K Ultra HD (3840 x 2160) \| Refresh Rate: 60 Hertz. Special Feature Smart TV Features: Google TV , Energy Rating: 2 Star \| Annual Energy Consumption: 134.38 kWh (HDMI 2.1 Compatible) Included Components 1 LED TV, 1 AC Power Cord, 1 Remote Control, 2 BatteriesConnectivity Technology Ethernet, HDMI, USB, Wi-FiAspect Ratio 16:9,Product Dimensions 7.9D x 95.8W x 57H Centimeters, Sound : 20 Watts Output \| 2ch \| Open Baffle Speaker\| DTS Digital Surround \| DTS:X \| Dolby Atmos, Dolby AudioMake: SONY/SAMSUNG
194	NETWORK SWITCH :- SITC of 24-Port Gigabit Ethernet Unmanaged PoE+ Switch with 190W PoE Budget and 16 Ports PoE+ , • NETWORK CONFIGURATION: Gigabit Switch 24 Port (10/100/1000 Mbps) RJ45 LAN Splitter Ethernet Switch• Plug and play: easy setup of the LAN distributor Gigabit switch, no software and no configuration requireMake: Netgear, Model (GS324P) or equivalent CISCO/Extreme
195	SITC of PoE Switch 16 Port, Gigabit Ethernet Unmanaged Network Switch - with 16 x PoE+ @ 76 W Upgradeable, Desktop, Wall Mount or Rackmount, and Limited ProtectionMake: Netgear, Model(GS116LP) or equivalent CISCO/Extreme
196	SITC of 8-Port Gigabit Ethernet Unmanaged PoE Switch - with 8 x PoE+ @ 123W Upgradeable, Desktop/RackmountMake: Netgear, Model(GS108PP) or equivalent CISCO/Extreme
197	Supplying and laying of solid bare copper conductor 4 pair unshielded twisted pair (UTP) Cat 6 cable FR PVC Jacket in dedicated pvc conduits on slab or wall as recessed/surface manner in/c connection with necessary RJ 45 connector etc as required.
198	SITC of 6U Network Rack with 4 Power Socket and AC Axial Cooling Fan -Transparent Glass Door, Metal Cabinet Box Wall mount (Size 6: 45 X 55 X 35 cm), Make: D Link/CP Plus
199	SITC Network Rack/Cabinet/with Lock/Server Rack with Power Socket - 2U - Wall Mount - (Metal) Transparent Glass Door Cabinet Box with keylock. Make: D Link/CP Plus.
200	SITC of 10TB Purple Pro Surveillance SATA HDD 3.5 Internal Hard Drive HDD 7200 RPM 512MB Cache CMR - WD102PURP, Make: Western Dlgital/ Ceagate Skyhawk./Matrix
201	Supplying, installation, testing and commissioning of following ratings online UPS with inbuilt isolation transformer, 50/60Hz (Auto sensing) frequency, P.F range 0.95-0.99, voltage regulation +/-1%, Pure sine wave form, total harmonic distortion < 5% with full load, Noise level 50db at 1m, LED indication for Normal mode/Load on battery/Load on bypass/System fault, Audible alarm for Mains failure, low battery, Overload, fault and Bypass mode complete with M. S Rack for mounting battery bank, Battery inter link cables and all other necessary accessories including connections etc. as required:- 2 kVA, 1 Ph input/1 Ph output Online UPS with 7200 VAH battery bank for minimum 2 hours Backup:-
202	Supplying and installation of Galvanized Iron (GI) Single-Arm 7 M Octagonal Pole For Outdoor Street light, 70 TOP 130 BOTTOM 200X200X12MM, 3 to 4 m thickness BASE PLATE Hot Dip Galvanizing FINISH 80 MICRON.
203	Supplying and installation of Galvanized Iron (GI) Double-Arm 7 M Octagonal Pole For Outdoor Street light, 70 TOP 130 BOTTOM 200X200X12MM, 3 to 4 m thickness BASE PLATE Hot Dip Galvanizing FINISH 80 MICRON.
204	Supplying and fixing of the following modular accessories including necessary connection etc. as required. (i) 5 step fan regulator (2M):-
205	(ii) RJ45 LAN socket outlet (1M):-
206	(iii) Switch board indicator lamp (1M):-
207	(iv) Buzzer call bell (1M):-
208	(v) Bell push SP (1M) :-
209	(vi) Blank plate (1M):-
210	(vii) 20/25 amps single phase motor starter switch (2M):-
211	Supplying and laying of the following sizes XLPE insulated PVC sheathed aluminium conductor armoured cable with necessary cable lugs and connection etc as required. (i) 3 core 4 Sq mm
212	(ii) 4 core 95 Sq mm
213	Excavation of earth for cable trench of 800mm depth & 300mm width in all kinds of soil including back filling of cable trench with the excavated soil with 20cm layer of sand, 3.5 nos bricks per metre for protection including ramming, consolidating to the original shape as per dirrection of Site Engineer :-
214	Drawing of armoured/un-armoured cable with proper saddling etc as required:-
215	Supplying and fixing of heat shrinkable cable end termination kits of following sizes : -Havells/Polycab/KEI - 3.5 core or 4 core 70/95/120/150 sqmm size:-
216	Supplying and fixing of thermoplastic cable junction box with connectors suitable for following sizes cable : - 1.5 sqmm - 4 sqmm Cable:-
217	Supplying & fixing of G.I. pipe (medium gauge) bracket fabricated at suitable angle for fixing of outdoor light on wall/ RCC base with necessary MS clamp, nut, bolt etc as required:- 40 mm dia
218	Supplying and fixing of the following sizes PVC conduit (medium gauge) on surface with all accessories etc. as required. (i) 19/20 mm dia
219	(ii) 25 mm dia
220	(iii) 40 mm dia
221	Supplying and fixing of the following sizes GI (in recess) and plastic (on surface) modular switch boards etc. as required.(Havells/Schnider/Philips) (i) 4 module GI switch board:-
222	(ii) 6 module GI switch board:-
223	(iii) 8 module GI switch board:-
224	(iv) 12 module GI switch board:- Please Enable Macros to View BoQ information

Tender Documents

SR No	FileName	File Description
1	Click here to download tender document	Tender Documents
2	Click here to download tender document	Tender Documents
3	Click here to download tender document	Tender Documents
4	Click here to download tender document	Tender Documents
5	Click here to download tender document	Tender Documents

Also Visit

Tenders

Tripura Tenders

Electrical Industry Tenders

Electrical Work Tenders

Electrical Maintenance Tenders

Disclaimer

We takes all possible care for accurate & authentic tender information, however Users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender.

Top

Tender For Construction Of Sp Office At East Bank Of Jagannath Dighi At Udaipur , Gomati Tripura Including Water Supply, Sanitary Installation And Internal Electrical Installation. (Balance Part)., Udaipur-Tripura

Tender Documents

Disclaimer

About Us

Services

Browse Tenders

For Sales Inquiry

Tender For Construction Of Sp Office At East Bank Of Jagannath Dighi At Udaipur , Gomati Tripura Including Water Supply, Sanitary Installation And Internal Electrical Installation. (Balance Part)., Udaipur-Tripura

Tender Documents

Disclaimer

OTP Verification

About Us

Services

Browse Tenders

For Sales Inquiry

Connect With Us