|
| 1 | Earthwork in excavation in foundation trenches in ordinary soil (vide classification of soil item-A) and disposal of excavated earth as obtained to a distance upto 50 M. including all lifts, levelling, ramming the foudation trenches, removing roots of trees, shrubs all complete as per approved design, building specification and direction of E/l. |
| 2 | Extra for earth work in hard soil as per specification and direction of E/I. (vide classification of soil item - B). |
| 3 | Earth filling in foundaion trenches and plinth in layers not exceding 150 mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I. (mode of measurement compacted volume)25 % of Total earth Excavated For Fdn. |
| 4 | Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including' cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/l (Mode of measurement complacted volume). |
| 5 | Providing designation 75A one Brick Flat Soling joints with local sand including cost of watering taxes royalty all complete as per building specification & direction of E/I. |
| 6 | Providing designation 75A brick work in CM (1:6) in superstructure with approved quality of clean coarse & of F.M. 2.5 including providing 10mm thick mortar joints cost of screening, racking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I. |
| 7 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering-All work up to plinth level :1:4:8 (1 Cement : 4 coarse sand ) : 8 graded stone aggregate 40 mm nominal size ) |
| 8 | Providing and fixing at or near ground level precast cement concrete in kerbs, edgings etc. as per approved pattern and setting In position with cement mortar 1:3 (1 Cement : 3 coarse sand), including the cost of required centering, shuttering complete. |
| 9 | Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.“(Note :- Cement content considered in this item is @ 330 kg/cum.“Excess/ less cement used as per design mix is payable/recoverable separately). |
| 10 | Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete |
| 11 | Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing: |
| 12 | Centering and shuttering including strutting, propping etc. and removal of form work for :Retaining walls, return walls, walls (any thickness) including attached pilasters, buttresses, plinth and string courses fillets, kerbs and steps etc. |
| 13 | Providing TMT steel reinforcement as per approved design & drawing. |
| 14 | Providing 12mm thick cement plaster (1:6) with with clean coarse sand of F.M. 1.5 and including screening, curing with all leads and lifts of water, scaffolding, taxes and royalty all complete as per building specification and direction of E/I |
| 15 | Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade : New work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm) |
| 16 | Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slabover 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade includingrubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge :Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent. |
| 17 | Stone tile (polished) work for wall lining over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and cement slurry @ 3.3 kg/sqm including pointing in white cement complete. Granite of any colour and shade |
| 18 | Providing & fixing of White River (Stone Pebbles size of 2\\" to 2.50\\" dia in natural colour at site of work including loading, unloading, carriage and all taxes paid etc.and as per direction of officer in charge. |
| 19 | Stone work ashlar sunk or moulded or sunk and moulded upto floor five level in cement mortar 1:6 (1 cement : 6 coarse sand) including pointing with white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade :Red sand stone |
| 20 | Extra for stone work ashlar sunk or moulded in cornices |
| 21 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 22 | Supplying and stacking of good earth at site including royalty and carriage up to 1 km (earth measured in stacks will be reduced by 20% for payment). |
| 23 | Supplying and stacking at site dump manure from approved source, including carriage up to 1.0 km (manure measured in stacks will be reduced by 8% for payment)Screened through sieve of IS designation 20 mm |
| 24 | Supplying and stacking at site dump manure from approved source, including carriage up to 1.0 km (manure measured in stacks will be reduced by 8% for payment)Screened through sieve of IS designation 16 mm |
| 25 | Supplying and stacking at site dump manure from approved source, including carriage up to 1.0 km (manure measured in stacks will be reduced by 8% for payment)Screened through sieve of IS designation 4.75 mm |
| 26 | Supplying and stacking of well decayed cow dung manure at site including royalty and carriage up to 1.0 km (cow dung manure measured in stacks will reduced by 8% for Payment) |
| 27 | Fine dressing of the ground |
| 28 | Mixing earth and sludge or manure in the required proportion specified or directed by the Engineer-in-charge |
| 29 | Spreading of sludge, dump manure and / or good earth in required thickness as per direction of Engineer-in-charge (cost of sludge, dump manure and / or good earth to be paid separately). |
| 30 | Uprooting rank vegetation and weeds by digging the area to a depth of 60 cm, removing all weeds and other growth with roots by forking repeatedly, breaking clods, rough dressing, flooding with water, uprooting fresh growths after 10 to 15 days and then fine dressing for planting new grass, including disposal of all rubbish with all leads and lifts |
| 31 | Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately)Holes 1.2 m diameter and 1.2 m deep |
| 32 | Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately)Holes 90 cm diameter and 90 cm deep |
| 33 | Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately)Holes 60 cm diameter and 60 cm deep |
| 34 | Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately)Holes 45 cm diameter and 45 cm deep |
| 35 | Complete maintenance of the entire garden features having as per yard stick in the garden area i.e. lawn trees, shrubs, herbs, edge, flower beds, foliages, creepers etc. including hoeing, weeding, pruning, replacement of plants, gap filling, watering, mowing of lawn, grass cutting by lawn mover and brush cutter, removal of garden waste, applying insecticide, pesticide & fertilizers (whenever required) top dressing of lawn with good earth and manure and maintenance of other garden related works as directed by office-in-charge (Cost of Good Earth, Manure, Fertilizer, Insecticide, Pesticide will be provided by the Department & lawn mover and brush cutter with fuel and other T & P material/articles shall be provided by the contractor.) and as per direction of officer in charge. |
| 36 | Providing and stacking of Plumeria alba of height 165-180 cm. with 3-4 branches and thick stem in big size HDPE bags as per direction of the officer-in-charge. |
| 37 | Providing and stacking of Plumeria rubra of height 120-150 cm. with 3-4 branches and thick stem in big size HDPE bags as per direction of the officer-in-charge. |
| 38 | Supply and planting of 3-meter-high Terminalia Mantaly (Madagascar Almond), healthy and well-branched with a developed root system, including transportation to site, pit preparation, planting, staking, and maintenance such as watering and fertilizing for 3 months; measured and paid per tree (each). |
| 39 | Providing and stacking of Bottle palm of ht. 210-240 cm bottom girth 30-35 cm well developed in big HDPE bags. |
| 40 | Providing and displaying of Areca Palm plant, having ht. 90 cm to 1.20 m with 4 to 5 suckers, well developed, fresh and healthy with lush green foliage in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge. |
| 41 | Providing and Displaying Travelers palm well developed with fresh & healthy leaves foliage 210 to 240 cm ht specimen plant in 40 cm Cement Pot as per direction of the officer-in-charge. |
| 42 | Providing and Displaying Bismarckia Palm 115 to 180 cm ht., well developed 12 and above good color fresh and healthy leaves in 40 cm Cement Pot as per direction of the officer-in-charge. |
| 43 | Providing and Displaying Bamboo Buddha vally variety with umbrella shape having 120 to 135 ht. with fresh & healthy foliage well developed in 40 cm Cement pot multy branch, bushy as per direction of the officer-in-charge. |
| 44 | Providing and stacking of Clerodendrum inerme having ht. 25 cm to 30 cm multi branched in 20 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. |
| 45 | Providing and stacking of Ficus panda of height 90-105 cm. with 10-12 branches and healthy foliage, well formed in cement pots of size 30 cm as per direction of the officer-in-charge. |
| 46 | Providing and Displaying Ficus Starlight with fresh, healthy and attractive foliage 45 to 60 cm spread 75 to 90 cm ht., specimen bushy plant,in 35 cm Cement Pot as per direction of the officer-in-charge. |
| 47 | Providing and stacking of Gardenia jasminoides of height 45-60 cm. with 3-4 branches in earthen pots of size 20 cm as per direction of the officer-in-charge. |
| 48 | Providing and stacking of Duranta Golden, having ht.15 to 20 cm bushty shape with fresh and healthy leaves in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.. |
| 49 | Providing and stacking of Hamelia patens of height 30-45 cm. with 3-4 branches in poly bags of size 20 cm as per direction of the officer-in-charge. |
| 50 | Providing and stacking of Hibiscus rosasinensis of height 45-60 cm. with 3-4 branches in earthen pots of size 20 cm as per direction of the officer-in-charge. |
| 51 | Providing and displaying of Rhapis Excelsa Palm plant, having ht. 75 cm to 90 cm with 12 to 15 equal suckers, well developed, full of fresh & healthy leaves from bottom to top in 25 cm size Earthen pot/Plastic pot & as per direction of the officer-in-charge. |
| 52 | Providing and stacking of Tecoma gaudichaudi of height 45-60 cm. in earthen pots of size 20 cm as per direction of the officer-in-charge. |
| 53 | Providing and stacking of Tabernaemontana coronaria (chandni variegated) of height 45-60 cm. with 3-4 branches earthen pots of size 20 cm as per direction of the officer-in-charge. |
| 54 | Providing and stacking of plant Canna dwarf of height 25 to 30 cm., 2 to 3 suckers in earthen pots of size 20 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge. |
| 55 | Providing and stacking of Alternanthera species of height 15 cm to 20 cm, full of branches and foliage in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. |
| 56 | Providing and stacking of Chlorophytum (Green), full of leafy suckers in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge. |
| 57 | Providing and stacking of Jatropha multifida (red colour) of height 45-60 cm. with 2-3 branches in earthen pots of size 20 cm as per direction of the officer-in-charge. |
| 58 | Providing and stacking of Asparagus sprengeri of height 15 cm to 20 cm, full of leafy branches in 15 cm size of Earthen Pot / Plastic Pot & as per direction of the officer-in-charge.. |
| 59 | Providing and stacking of Syngonium (Butterfly) variegated with 2-3 suckers healthy foliage in Earthen Pot/Plastic Pot of size 20 cm. as per direction of the officer-in-charge. |
| 60 | Providing and stacking of Tradescantia, full of leaves in Earthen Pot/Plastic Pot of size 15 cm. as per direction of the officer-in-charge. |
| 61 | Providing & laying Selection no. 1 doob grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with required tools wooden and than rolling the surface with light roller make the surface smoothen and light watering the same maintenance for 30 days or more till the grass establish properly,as per direction of officer in charge |
| 62 | Column light made of mild steel with fine laser cut design and predefine logo closed by diffuser and have ingress protection for optical compartment. Fitting height 2.5 mtr above ground level with mid light illumination of 40W. The column section shall be of 500mmx500mm with top part predesigned LOGO with two street light of 50W for illuminating the side areas. Mid-section gives the homogeneous light output. All pole section Shall be welded by certified welders using high MIG welding process. The Service door shall be provided at bottom part of the pole which equipped with a C clamp with sliding nuts to accommodate a built in connection box. The control gear tray is prewired with MCB, terminal connectors for loop in loop out arrangement. The base plate of the pole is design with elongated foundation holes for fine alignment of the pole during installation. Fitting is made of mild steel with fine laser cut design and signage closed by PMMA diffuser tailored with lighting to suit your specific needs as per detail drawing. Color tolerance ,3 SCDM to avoid color deviation. All exterior parts are made of stainless steel. Diffused symmetric light without glare. Light output of source is more than 110lm/ watt, CRI>70, Surge protection 10k, operating voltage 140-270V, wired with Branded LEDs of Osram/Cree or equivalent and Fulham or equivalent constant voltage/current driver with efficiency>80%, power factor>0.9, THD<=10%. The CCT of led will be 3000k/4000k/5700k as required by the project. Proper thermal management for longer life of fixture. Led burning of 50,000 hours. Column light fixture is complete in all aspects with all accessories except foundation bolt. |
| 63 | Spike light for building/Tree facade. Fixture to be made of MS alloy in 10W LED engine with a beam of 36 degree to give a specified coverage to lit. The diffuser is toughened Clear glass of 6mm thickness with optical reflector to reduce glare controlled, Silicone clear gasket, SS fasteners. This luminaire contains built-in LED modules. Lifespan of the luminaire > 60,000 hours at 40°C. Driver efficiency >80%, power factor >0.90, Operating temp. -15°C to +50°C.THD <15%, |
| 64 | Bollard light made of GI sheet and have Ingress Protection of IP66 for optical compartment. The decorative Bollard shall be of height 1mtr above ground level with LED of 20W for area illumination and Bollard with top predesigned NOIDA LOGO laser cut to illuminate the surroundings with noticeable mode. The Bollard light section of 350mmx350mm x 3mm thickness up to 1mtr long with four side illuminated portion. Bollard is made of GI sheet with fine laser cut design tailored with lighting to suit your specific needs as per detail drawing. Luminaire primarily coated with epoxy resin and top coated with powder coat. All exterior parts are made of stainless steel. Light output of source is more than 110lm/ watt, CRI>70, Surge protection 4k, operating voltage 140-270V, wired with Branded LEDs of Osram/ Cree and Fulham or equivalent constant voltage/current driver with efficiency>85%, power factor>0.9, THD<=10%. The CCT of led will be 3000/4000/5000 as required by the project. Proper thermal management for longer life of fixture. Led burning of 50,000 hours. Fitting is complete in all aspects with all accessories except foundation bolt. |
| 65 | Underwater LED focus light with 18 LEDs/fixture. 10MM tempered glass, color temperature options, high grade stainless steel. Underwater lights surface mounted for waterbody applications, to highlight the water body . The fixtures are of high grade stainless steel 316 material, suitable for places near salt-water. NICHIA and CREE LED source is used in underwater lights. The lifespan for the fixtures is above 50,000Hrs. With 24VDC the lumen output is high. A narrow and wide beam optics are standard options to chose. Color temperature options for underwater lights is 2000K, 3000K and 6000K. RGB and RGBW is also possible with DMX control system. These lights come with 18 LEDs/fixture & 10MM glass. |
| 66 | Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/recessed steel/ PVC conduit as required. - 3 x 1.5 SQMM ( make : Polycab/ KEI/ RR Kabel) |
| 67 | Design, Manufacture, Supply, Installation, Testing and Commissioning of Panel Fabricated out of 16 SWG CRCA sheet steel, IP 65, floor mounting type with rain canopy The sheet steel shall undergo minimum 7 tank treatment followed by finishing powder coating of min 60 micron thickness. the board includes 415 /240 V electrolitic Aluminium Bus Bar, removable gland plates, cable glands, including connection with outgoing feeders complete in all respect, Panel Should Have Double Earthing Provision Which Connected to the Nearest Earth Grid. 1 no. 100A, 50KA 4P MCCB with microprocessor based releases, ON indication, 1 no. multifunction meter (showing all power parameters), with Selector Switch, Matching Cast Resin CT's. + 3 Nos 63A DP MCB For each Phase.with 3 Nos Astronomical Weekly programmable time switch (SST- 1min) ON Phase for automaitc switching of landscape light fixtures at sun set and sun rise or twilight (auto on/ auto off and auto mode) with manual override faiclity with 12/24 hour display format with suitable battery and indication for relay status i/c programming at site. |
| 68 | Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required. |
| 69 | Incoming cable for the feeder pillar . Supplying & Laying of Following sizes 1100 volt grade XLPE insulated PVC sheathed aluminium conductor armoured cables as per specification in existing trenches/pipes, cable trays, ducts, clamped to wall with suitable clamps including, saddles fixing bolts, connecting testing and commissioning as Required. - 3-1/2 CORE 50 Sqmm |
| 70 | Providing and fixing brass/C.I. stop cock of approved quality all complete as per specification and direction of E/I.15 mm dia |
| 71 | Providing and fixing G.M. non return valve Horizontal/Vertical type of approved quality as per specification and direction of E/I.25 mm dia |
| 72 | Providing and fixing G.M. non return valve Horizontal/Vertical type of approved quality as per specification and direction of E/I.32 mm dia |
| 73 | Making holes in walls for laying G.I. pipe and restoring the same after pipe laying as per specification and direction of E/I.125 mm thick wall |
| 74 | Making holes in walls for laying G.I. pipe and restoring the same after pipe laying as per specification and direction of E/I.250 mm thick wall |
| 75 | Supplying materials and labours for constructing inspection chamber of designation class 75B bricks size 750mm deep, 600 x 450mm internal dimension having 250mm wall thickness in cement mortar (1:6) including 12mm cement plaster (1:4) with punning on inside and cement plaster (1:6) with 600 x 475mm G.I. Cover with frame (weight not leaa than 36 kg) alongwith earth work in exacavation and 80mm thick P.C.C. (1:3:6) in foundation and refilling all complete as per specification and direction of E/I. |
| 76 | Supplying NP2 R.C.C. hume pipe with colour as work site as per direction of E/I.150mm dia |
| 77 | Approved basic rates construction materials for preparation of schedule of rates only, (Material should conform to relevent B.I.S. specification). The rates are inclusive of all taxes, royalty, cess and carraige but exclusive of contractor's profit and overhead charges -Special type of C.P. Bath room fitting for V.I.P. buildings (JAL, Jaguar, Marc or equivalent mark)Pillar cock |
| 78 | Approved basic rates construction materials for preparation of schedule of rates only, (Material should conform to relevent B.I.S. specification). The rates are inclusive of all taxes, royalty, cess and carraige but exclusive of contractor's profit and overhead charges -Special type of C.P. Bath room fitting for V.I.P. buildings (JAL, Jaguar, Marc or equivalent mark)Angular Stopcock /2 way bib cock |
| 79 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.75 mm diameter |
| 80 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter |
| 81 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.Single tee without door - 75x75x75 mm |
| 82 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.Single tee without door - 110x110x110 mm |
| 83 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 75 mm bend |
| 84 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.110 mm bend |
| 85 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall25 mm nominal outer dia Pipes |
| 86 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall32 mm nominal outer dia Pipes |
| 87 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc.15 mm nominal outer dia Pipes |
| 88 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.Concealed work, including cutting chases and making good the walls etc.20 mm nominal outer dia Pipes |
| 89 | Providing and placing on terrace (at all floor levels) polyethylene waterstorage tank, ISI : 12701 marked, with cover and suitable lockingarrangement and making necessary holes for inlet, outlet and overflowpipes but without fittings and the base support for tank. |
| 90 | Cost of Drilind 200 mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site.(a) From 0.00 M to 50.00 M below G.L. |
| 91 | Cost of Drilind 200 mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site.(b) From 51.0 M to125.00 M |
| 92 | Cost of Drilind 200 mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site.(c) From126.0 M to175.00 M |
| 93 | Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge.200 mm nominal size dia |
| 94 | Development of tube well in accordance with IS : 2800 (part I) andIS: 11189, to establish maximum rate of usable water yield withoutsand content (beyond permissible limit), with required capacity aircompressor, running the compressor for required time till well isfully developed, measuring yield of well by \\"V\\" notch method or anyother approved method, measuring static level & draw down etc. bystep draw down method, collecting water samples & getting testedin approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessoriesetc., all as per requirement and direction of Engineer-in-charge |
| 95 | Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of:200 mm dia |
| 96 | Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete.200 mm clamp |
| 97 | Supplying 100mm dis submersible pump sets confirming to 8034 and motor confirming to IS 9283 pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415 + 10, 3HP, 50 Hz, AC supply with cable guard, thurst carbon/fiber bearing to withstand entire hydraulic thurst, water proof winding shall be provided. The pump set shall be suitable for diret coupling Pump shall have suitable outlet as per manufacturers design. Anti thurst stream lined non return valve shall be provided with pump, 3 meter submersible copper conductor cable in single/double run shall be provided with each pump.Submersible pump set 100mm dia (with Polypropylene/Noryl Impeller) up to 20 stages5 HP |
| 98 | Supply fitting and fixing of standered make starter pannel Board with arrangement of all necsssury protection including all taxes , all complete job as per direction of E/I. |
| 99 | Supplying fitting and fixing 3 crore 4 sqmm Flat copper submersible cable FINOLEX / HEVELS make including all taxes ,royalty etc all complete job as per direction of E/I. |
| 100 | Supply fitting and fixing lowering 40 mm dia G.L. collumn pipe - do - do - all complete job as per direction of E/I. |
| 101 | 15 FEET HIGH BRONZE STATUE OF A PROMINENT PERSONALITY AS PER DIRECTION OF EICBronze specifications shall be Copper:82- 85%, Zinc:3-5%, Lead:3- 5%, Tin:3-5% |
| 102 | WATER FEATURE FOAM JETSupplying, Installing, Testing & Commissioning of Water Fountain System , As per the specifications : Jet nozzle 4 set of supremepools.submersible water proof light made out of Noryl / stretched stainless steel and cable gland suitable to be fitted with emitter type power with all in one symmetrical optical lens of 85% effeciency step tempered glass 8mm with protection class of IP-68 i/c connection & water proof jointing etc as required 4 set of supremepools,.Indoor type Cubical Control Panel made of 16 gauge CRC sheet powder coated with 4 Starter of supremepools, Single phase preventer, MCB, volt-meter, Amp meter, TP MCB's, for switching on and off pumps and lights, Protection circuits etc with reputed makes L& T, Schneider . ,Complete with relays 4nos, of supremepools.Step Down/Power Supply Transformer For the Light 8 nos of supremepools ,.Enclosure Box For the Light 4 sets,. SS Light Stand 1 sets,.Recirculation submersible pump to acheive the design flow with proper head and discharge 4 nos, of supremepools.Capital fitting in uPVC such as control valves NRV's etc. required for the final installations 4 job,.Supply, installation, testing & commissioning of uPVC pressure Pipes with plain socket suitable for solvent cement jointing conforming to IS:4985/2000 & fittings conforming to IS 7834/87 including all necessary fittings and specials such as bends, tees, unions, reducers, flanges and plugs including necessary 1 job,. Complete Electrical Work such as conduits, bends, fittings etc. of required sizes 1 job,.Wires of Various sizesincluding accessories like glands, stickers, sub tape etc for final equipment installation 1 job,. of supremepools Providing MEP Shop drawings For the WF with all nozzles in details 1 job,. Installing, Tasting & Commissioning of the Water Feature equipments 1 job |
| 103 | Providing and fixing in position Non-Illuminated Pole mounted Speed limit -Informational signage consisting of the following: Signs made in Modular Aluminium extrusions (Alloy 6060 as per European standards EN755-2-2008 tensile strength 190 MPA typical BHN is 70 from virgin aluminium homogeneous billet) with Premium grade Anodizing (Thickness 15-20 microns, ISO:9001-2008 certified) International standards, with Lifetime warranty under normal working conditions. 1. Signage face made out of ‐ 3mm thick Aluminum sheet fabrication with a white retroreflective film, fixed to horizontal structural truss. Graphics as per requirement of respective vinyl and shade.2. Signage structure ‐ MS square post shaped 50 x 50 x 5 mm or 60 x 40 x 5 mm and mounting square sections, powder coated as per . Mounting square section span and the wind loads.3. Sign frame - Cosign make modular extruded aluminium profile Module plus outdoor system -Consisting of main pole 80 mm Octagonal shaped (1 nos) screw fitted with M.S structure vertically & horizontally, Coverlist profile inserted in octagonal shaped profile to hide screw fitting arrangement completely. Plastic moulded endcap (black coloured) on top side to cover octagonal shaped profile, attached to with 50 mm depth aluminium frame with 80 mm radius round corners as per design requirements with 80 mm radius round corners as per design requirements for media signage mounting , with media accommodation depth of 6 mm, frame screw fitted at multiple position along vertical and horizontal side facing the octagonal pole.4. Media - ACP /Acrylic router cut - vinyl wrapped / pasted with thickness upto 5 mm can be pasted (with help of dual lock or foam based 3M make double sided tape) on 50 mm depth profile (on both side) including post, RCC foundations, electrical connections (as required), cutting and opening the floor finish (as required) at location, and making good to match the original finish after fixing and installation of signage with all accessories such as thimbles, end connectors, nut‐inserts, screws, rivets, bolts, washers, nuts, etc. all complete with due considerations to harsh outdoor conditions as per approved design/ drawings and instructions of the engineer-in-chargePost Size 3000mm, Frame Size: 750mm x 250mm & 450mm x 450mm |
| 104 | Providing and fixing in position Non-Illuminated Pole mounted Speed limit -Informational signage consisting of the following: Signs made in Modular Aluminium extrusions (Alloy 6060 as per European standards EN755-2-2008 tensile strength 190 MPA typical BHN is 70 from virgin aluminium homogeneous billet) with Premium grade Anodizing (Thickness 15-20 microns, ISO:9001-2008 certified) International standards, with Lifetime warranty under normal working conditions. 1. Signage face made out of ‐ 3mm thick Aluminum sheet fabrication with a white retroreflective film, fixed to horizontal structural truss. Graphics as per requirement of respective vinyl and shade. 2. Signage structure ‐ MS square post shaped 50 x 50 x 5 mm or 60 x 40 x 5 mm and mounting square sections, powder coated as per . Mounting square section span and the wind loads. 3. Sign frame - Cosign make modular extruded aluminium profile Module plus outdoor system -Consisting of main pole 80 mm Octagonal shaped (2 nos) screw fitted with M.S structure vertically & horizontally, Coverlist profile inserted in octagonal shaped profile to hide screw fitting arrangement completely. Plastic moulded endcap (black coloured) on top side to cover octagonal shaped profile, attached to with 50 mm depth aluminium frame with 80 mm radius round corners as per design requirements with 80 mm radius round corners as per design requirements for media signage mounting , with media accommodation depth of 6 mm , frame screw fitted at multiple position along vertical and horizontal side facing the octagonal pole.4. Media - ACP /Acrylic router cut - vinyl wrapped / pasted with thickness upto 5 mm can be pasted (with help of dual lock or foam based 3M make double sided tape) on 50 mm depth profile (on both side) including post, RCC foundations, electrical connections (as required), cutting and opening the floor finish (as required) at location, and making good to match the original finish after fixing and installation of signage with all accessories such as thimbles, end connectors, nut‐inserts, screws, rivets, bolts, washers, nuts, etc. all complete with due considerations to harsh outdoor conditions as per approved design/ drawings and instructions of the engineer-in-charge |
| 105 | Providing and fixing in position Non-Illuminated Pole mounted Speed limit -Informational signage consisting of the following: Signs made in Modular Aluminium extrusions (Alloy 6060 as per European standards EN755-2-2008 tensile strength 190 MPA typical BHN is 70 from virgin aluminium homogeneous billet) with Premium grade Anodizing (Thickness 15-20 microns, ISO:9001-2008 certified) International standards, with Lifetime warranty under normal working conditions. 1. Signage face made out of ‐ 3mm thick Aluminum sheet fabrication with a white retroreflective film, fixed to horizontal structural truss. Graphics as per requirement of respective vinyl and shade.2. Signage structure ‐ MS square post shaped 50 x 50 x 5 mm or 60 x 40 x 5 mm and mounting square sections, powder coated as per . Mounting square section span and the wind loads.3. Sign frame - Cosign make modular extruded aluminium profile Module plus outdoor system -Consisting of main pole 80 mm Octagonal shaped (2 nos) screw fitted with M.S structure vertically & horizontally, Coverlist profile inserted in octagonal shaped profile to hide screw fitting arrangement completely. Plastic moulded endcap (black coloured) on top side to cover octagonal shaped profile, attached to with 50 mm depth aluminium frame with 80 mm radius round corners as per design requirements with 80 mm radius round corners as per design requirements for media signage mounting , with media accommodation depth of 6 mm , frame screw fitted at multiple position along vertical and horizontal side facing the octagonal pole.4. Media - ACP /Acrylic router cut - vinyl wrapped / pasted with thickness upto 5 mm can be pasted (with help of dual lock or foam based 3M make double sided tape) on 50 mm depth profile (on both side) including post, RCC foundations, electrical connections (as required), cutting and opening the floor finish (as required) at location, and making good to match the original finish after fixing and installation of signage with all accessories such as thimbles, end connectors, nut‐inserts, screws, rivets, bolts, washers, nuts, etc. all complete with due considerations to harsh outdoor conditions as per approved design/ drawings and instructions of the engineer-in-charge900 mm (W) x 1200 mm (H) Approx (2400 mm post height) |
| 106 | ARTISTIC SCULPTURE DEPICTING TRIBALS, FREEDOM FIGHTERS/LEADER, TRIBAL ART WITH SCULPTURE\ AND EXTERNAL CONCEPT Creation - 4 MTRX 3 MTRX 3 MTR Creating design and creation of Art work concept on given subject. With initial visit to site, preparation of various designs with different material, providing the samples, layout for approval, improvisation in short listed creative’s and making of final layout for final production by enlargement of drawing as per ratio of actual size, to prepare detailed working shop drawings (full scale) based on the Concept drawings / Views / site conditions, Display of actual size dummy /mock up Fabricated in sun board with digital print for client approval. Artwork Execution:Execution of approved design in ss 316 grade steel / stone/casted alluminum pu colored antique as per approved finish (mrf/akzo nobel) and protected against discoloration by sealing it with top coat of Mrf/Akzo nobel clear Pu. Proper support system will be given as per approved shop drawing & Staad file etc., to withstand high wind pressure. The sculpture will be free from any Undulation/Dent unless it is part of the design. The cost is inclusive of transport/packing and installation of the same at site. Fastener/screws hilti or equivalent company.Approved Make - East Craft Designs Pvt. Ltd., New Delhi / Ram Sutar or equivalent artist with relevant experience |
| 107 | CARRIAGE OF MATERIALS : SAND (UPTO 38 KM LEAD) |
| 108 | CARRIAGE OF MATERIALS : CHIPS (UPTO 37 KM LEAD) Please Enable Macros to View BoQ information |
