Sales : +91-777 804 8217
| Sl. No. | Item Description |
| 1 | CREMATORIUM CIVIL WORKS |
| 2 | 2.8.1:Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil |
| 3 | 2.26.1:Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials.All kinds of soil |
| 4 | 2.25:Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m. |
| 5 | 5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more |
| 6 | OD256079/2025-2026:Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. All work upto plinth level Concrete of M30 grade with minimum cement content of 350 kg /cum (Excess or less cement used as per design mix will not be payable or recoverable separately ) |
| 7 | OD256080/2025-2026:Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. All work above plinth level upto floor V levelConcrete of M30 grade with minimum cement content of 350 kg /cum (Excess or less cement used as per design mix will not be payable or recoverable separately ) |
| 8 | OD313413/2025-2026:Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. All work upto plinth levelConcrete of M25 grade with minimum cement content of 330 kg /cum (Excess or less cement used as per design mix will not be payable or recoverable separately ) |
| 9 | OD256080/2025-2026:Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. All work above plinth level upto floor V levelConcrete of M30 grade with minimum cement content of 350 kg /cum (Excess or less cement used as per design mix will not be payable or recoverable separately ) |
| 10 | 5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete |
| 11 | 5.9.5:Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers |
| 12 | 5.9.6:Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts |
| 13 | 4.1.8:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 14 | 50.6.1.5:Solid block masonry using pre cast solid blocks ( Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 Part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement : 6 coarse sand) etc complete |
| 15 | 13.16.1:6 mm cement plaster of mix:1:3 ( 1 cement : 3 fine sand) |
| 16 | 13.4.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 coarse sand) |
| 17 | 13.80:Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 18 | 13.82.2:Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound) content less than 50 grams/ litre, of approved brand and manufacture including applying additional coats wherever required, to achieve even shade and colour.Two coats |
| 19 | 13.85.3:Applying priming coats with primer of approved brand and manufacture, having low VOC ( Volatile Organic Compound) content.With water thinnable cement primer on walls surface having VOC content less than 50 grams / litre |
| 20 | 9.117.1:Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1 mm), with wall thickness 2.0mm (±0.2 mm), corners of the door frame to be jointed with galvanized brackets and stainless steel screws, joints mitred and plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 x 19 mm and 1 mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer's specification and direction of Engineer-in-chargeExtruded section profile size 48x40 mm |
| 21 | 9.118.1:Providing and fixing to existing door frames24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness,fixed to the shutter styles by means of plastic/galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-in-charge( For W.C. and bathroom door shutter). |
| 22 | 9.147B.1:Providing and fixing factory made uPVC white colour fixed glazed windows/Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.) |
| 23 | 10.30.2:Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows all complete with :5.5 mm thick glass panes |
| 24 | 11.39:Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS: 15622, of approved make in colours White, Ivory, Grey, fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 Coarse sand), including grouting the joints with white cement and matching pigments etc., complete. |
| 25 | 8.31:Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in- Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 26 | 11.46.2:Providing and laying Vitrified tiles indifferent sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.Size of Tile 600x600 mm |
| 27 | 11.41.2:Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600 x 600 mm. |
| 28 | 16.1:Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres. |
| 29 | 16.91.1:Providing and laying factory made chamfered edge Cement Concrete paver blocksin footpath, parks, lawns, drive ways or light traffic parking etc, of required strength,thickness & size/ shape, made by table vibratory method using PU mould, laid inrequired colour & pattern over 50mm thick compacted bed of sand, compacting andproper embedding/laying of inter locking paver blocks into the sand bedding layerthrough vibratory compaction by using plate vibrator, filling the joints with sand andcutting of paver blocks as per required size and pattern, finishing and sweepingextra sand. complete all as per direction of Engineer-in-Charge.60mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern. |
| 30 | 12.1.3:Providing corrugate G.S. sheet roofing including vertical/ curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete ( up to any pitch in horizontal / vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.0.63 mm thick with zinc coating not less than 275 gm/m2 |
| 31 | 50.10.1:Steel work in built up G I tubular ( round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting,fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete |
| 32 | 50.10.2:Steel work for purlin/single section with G I pipes including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete |
| 33 | OD256084/2025-2026:Door of primary chamber:- Front opening, vertical sliding, counter weight balanced with view port using MS sheet supported and connected using MS flat, MS pipe and MS channel of minimum thickness of 6 mm. The door to be operated using steering wheel with bearings and MS Sprocket roller chain of suitable size , door to have ceramic wool, SS mesh 304 grade with finished thickness 6-7cm necessary fittings for proper closure painting with hammertone silverash paint inclusive of primer and thinner including all labour, installation, transportation charges etc complete. |
| 34 | OD256086/2025-2026:Constructing MS Chimney foundation in M20 concrete as per technical specification. Rate is inclusive of earth work, P.C.C ,centering shuttering , reinforcement and 25mm dia foundation bolt nut as per requirement including labour charges all complete as per the drawings |
| 35 | OD256085/2025-2026:Providing and laying Gas line using MS pipe including fixing of 50mm and 15mm dia non-return valves, 1/2" Suraksha hose,1/2" hydraulic hose, 1/2" LPG and brass adaptor ,1/2” and 2” regulators ,1/2" pressure gauge , 100KW high pressure burner and 1" LPG mass weighing machine. Provision for shutting down the burner to maintain the temperature between 800 and 850 degree celsius also need to be provided all complete as per the drawings and as per requirement including painting the gas lines using red and yellow paint and labour charges etc |
| 36 | OD256078/2025-2026:Providing and fixing MS Chimney total 30m height on RCC Chimney foundation , as per CPCB norms and State PCB norms, using MS flange bottom outer dia 1.5m and inner dia 1m and MS sheet diameter varying from 1m to .8m meters for a height of 6m, from 0.8m to 0.6m meters for a height of 6m , from 0.6m to 0.325m meters for a height of 6m and topmost part with diameter 0.325m for a height of 12m. MS sheet of thickness minimum 8mm for a height of 6m and 6mm for the remaining height to be used with inner lining lagged with high alumina refractory in the conical area . Providing and fixing full length MS ladder using MS pipe and rods -at 11m with platform and remaining 18m ladder to be provided. Fixing connection to chimney using 325 mm dia MS pipe need to be provided and sampling port at 11m from the chimney bottom. Lightning arrestor of 50m capacity using GI strip 25mm x3mm need to be provided and fixed using 32mm PVC pipe at the top of the chimney and should be connected to the earthing pit in the ground. The rate is inclusive of earthing compound but exclusive of charge for construction of earthing pit. Providing and fixing accessories such as nut bolt washers of appropriate sizes ,8mm asbestos rope and BI metal 4" dia (0-300 range) dial thermometer .Rate is inclusive of painting the chimney with black paint including primer and thinner, carriage of materials, cost of installation, erection. Other Engineering Organisations including labour charges all complete as per the drawings |
| 37 | OD256087/2025-2026:Providing and fixing purification tank using MS sheet of minimum size 2.55 m x 1.26 m x 1.26 m. Providing and fixing ventury scrubber of dia 750 x 1500 (Top Dish - 200 MM), MOC - SS 304, spray header, spray nozzle , CRI valves,MS flanges,1HP Pressure Pump ,1" dia drain Valve and stand for scrubber. Providing and fixing cyclon separator of dia - 800 x 1500 (Top Dish - 200 MM),MOC - SS 304, stand for cyclone seperator and mist eliminator of dia - 300 x 500 (Top Dish - 200 MM ).Providing and fixing centrifugal type 7.5 HP blower with dynamically balanced impeller made of SS 304 and driven by belt and En8 shaft of inlet size of dia 10"flange and outlet size 8" with outlet orientation vertical anticlockwise from the drive end and a motor speed of 2880 RPM . Providing and fixing 200 mm MS pipe and MS bend, 1000 litre water tank of good approved quality with appropriate valves and fittings all complete as per the drawings |
| 38 | OD256082/2025-2026:Secondary Chamber Separate secondary chamber of minimum outside dimension 0.8 m x 0.8 m x 0.8 m and inner dimension 0.35 m x 0.35 m x 0.35 m with secondary chamber stand of outside dimension 0.85 m x 0.85 m x 0.9 m made out of MS sheet of minimum plate thickness of 5 mm connected by MS angles and provided with refractory lining with insulation brick and able to withstand 1400 deg C. Separate ductarrangement with MS duct having minumum dimension 4.0 m x 0.45 m x 0.45 m and provided withOther Engineering Organisationsrefractory lining with insulation brick and able to withstand 1400 deg C complete including black colour painting inclusive of primer and thinner including all labour, installation, transportation charges ETC. |
| 39 | OD256083/2025-2026:Electrical Items For Gas crematorium with PVC PIPE 25 MM BEND 25 MM 3 WAY JTN BOX 25 MM TEE 25 MM FLEXIBLE HOSE 25 MM PHASOR CLAMP 25 MM GRIP 6 MM SCREW 25 MM / 1" SCREW DRY WALL 1 1/2" TIE 250 INSULATION TAP R B G Y COPPER 5 KG ANCHOR BOLT 6 MM C PVC PIPE 1 " CPVC ELBOW 1 " CPVC TEE 1 " CPVC 1" 45 UNION CPVC 1" VALVE CPVC 1" MTA CPVC 1" FTA CPVC 1" TUFFLON TAPE CPVC COUPLING 1" PVC FTA 1" VALVE PVC 1" PIPE PVC 1" ELBOW PVC 1" PVC TEE 1" CPVC SOLVENT PVC SOLVENT FOOT VALVE 1" WIRE 2.5 MM WIRE 1.5 MM WIRE 4 KG THERMO COUPLE LABOUR PANEL BOARD --3 PHASE CONTACT - 4 NOS TIMER RELY 25 A CAPASITOR - 3.0 KVAR & 2.7 KVAR NC & NO - 4 POLE - 1 NO AND 2 POLE - 2 NOS 32 A ISOLATOR - 4 POLE MCB CONNECTORS - 10 A - 14 NOS AND 5 A - 14 NOS TEMP INDICATORS - 2 NOS INDICATORS - 7 NOS START SWICH - 2 NOS STOP SWICH - 2 NOS ROTARY SWITCH - 3 NOS |
| 40 | OD256088/2025-2026:SS Bed of 20mm diameter arranged suitably in primary chamber with installation , fixing and transportation charges etc complete |
| 41 | OD256081/2025-2026:Primary Chamber with refractory work Primary Chamber of minimum outside dimension 2.9 m x 1.9 m x1.5 m and inner dimension 2.7m x 1.1 m x 0.9 m made with MS sheet of minimum plate thickness of 5Other Engineering Organisationsmm properly supported and connected using MS channels, MS angles and MS flat with inside refractorybrick lining insulation, sidearch, endarch , railbrick 70% STD fixed using fireclay , acooset, castableP RI CEnormal, castable super and insulate 7 withstanding 1400 degree heat, painting with hammerton silver ash paint with primer and thinner including all labour, conveyance and installation charges etc complete. |
| 42 | OD256077/2025-2026:Rail and trolley: Rail & Trolley of minimum outside dimension 3.35 m x 0.91 m x 0.61 m:- In two parts to lay body inside the primary chamber using MS angles, MS flat, MS pipe ,MS rods plain and MS square rod polished with proper wheel and wheel bearing mechanism , gearbox (size 850x250x90mm with gear box shaft right hand 2nos and drive pinion shaft) for movement painting with hammerton silverash paint with primer and thinner with all labour, transportation and installation charges etc complete |
| 43 | OD308436/2025-2026:Lettering with vinyl sticker type letter of standard size, font and colour as specified by the Engineer in charge. |
| 44 | OD308437/2025-2026:Providing and fixing braille directional signage with ADA Braille sign in Polymer sheet with tactile characters and picture. 2 mm thick of standard size round, square or triangle in shape fixed by foam tape mounting including cost of materials and fixing charges etc complete |
| 45 | OD308438/2025-2026:Providing and fixing braille pictogram signage with Aluminium backed acrylic sheet with tactile characters and picture. 2 mm thick of standard size round, square or triangle in shape fixed by foam tape mounting including cost of materials and fixing charges etc complete |
| 46 | OD308440/2025-2026:Providing and fixing signage with vinyl sticker type sheet including printing ncecessary emblems of standard size, font and colour as specified by the Engineer in charge |
| 47 | OD308441/2025-2026:Providing and laying Self Adhesive Polyurethane/Thermoplastic Elastomer Tactile Tiles of size 300X300mm in any colour for Hazard (Dots) & Directional (Lines) for visually impaired persons having size of 300x300x2 mm at base and 6.5 mm at projected area of Dash and Dots including cost of all materials and labour charges etc. |
| 48 | COMMUNITY HALL CIVIL WORKS |
| 49 | 2.6.1:Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.All kinds of soil |
| 50 | 2.25:Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m. |
| 51 | 4.1.8:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 52 | 20.2.3:Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by percussion drilling using Direct mud circulation (DMC) or Bailer and chisel technique by tripod and mechanical Winch Machine all complete, including removal of excavated earth with all its lifts and leads (length of pile for payment shall be measured up to bottom of pile cap).600 mm dia piles |
| 53 | 20.6.1.1:Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge/Anchor piles method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer in-charge.Single pile upto 50 tonne capacityInitial test (Test Load 2.5 times the Safe capacity) |
| 54 | 20.6.1.2:Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge/Anchor piles method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer in-charge.Single pile upto 50 tonne capacityRoutine test (Test Load 1.5 times the Safe capacity) |
| 55 | 20.9:Integrity testing of pile using Low Strain / Sonic Integrity Test/ Sonic Echo Test method in accordance with IS 14893 including surface preparation of pile top by removing soil, mud, dust & chipping lean concrete lumps etc. and use of computerised equipment and high skill trained personal for conducting the test & submission of results, all complete as per direction of Engineer-in-charge. Note:- The inclusion of the above item in the schedule of work shall be judiciously decided by the technical sanctioning authority, keeping in view the quality control, type of soil strata & importance of the project. |
| 56 | 5.11.1:Extra additional height in centering, shuttering where ever required with adequate bracing, propping etc. including cost of de-shuttering and decentering at all levels, over a height of 3.5m, for every additional height of 1 metre or part thereof (Plan area to be measured).Suspended floors, roofs, landing, beams and balconies (Plan area to be measured) |
| 57 | 5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more |
| 58 | 5.22A.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo - Mechanically Treated bars of grade Fe-500D or more |
| 59 | OD256076/2025-2026:Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. All work upto plinth levelConcrete of M25 grade with minimum cement content of 330 kg /cum (Excess or less cement used as per design mix will not be payable or recoverable separately ) |
| 60 | OD256075/2025-2026:Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. All work above plinth level upto floor V levelConcrete of M25 grade with minimum cement content of 330 kg /cum (Excess or less cement used as per design mix will not be payable or recoverable separately ) |
| 61 | 5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete |
| 62 | 5.9.19:Centering and shuttering including strutting, etc. and removal of form for:Weather shade, Chajjas, corbels etc., including edges |
| 63 | 5.9.2:Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. |
| 64 | 5.9.3:Centering and shuttering including strutting, etc. and removal of form for:Suspended floors, roofs, landings, balconies and access platform |
| 65 | 5.9.5:Centering and shuttering including strutting, etc. and removal of form for:Lintels, beams, plinth beams, girders bressumers and cantilevers |
| 66 | 5.9.6:Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts |
| 67 | 5.9.7:Centering and shuttering including strutting, etc. and removal of form for:Stairs, (excluding landings ) except spiral - staircases) |
| 68 | 50.6.1.5:Solid block masonry using pre cast solid blocks ( Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 Part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement : 6 coarse sand) etc complete |
| 69 | 13.16.1:6 mm cement plaster of mix:1:3 ( 1 cement : 3 fine sand) |
| 70 | 13.4.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 coarse sand) |
| 71 | 13.39.1:Colour washing such as green, blue or buff to give an even shade:New work ( two or more coats) with a base coat of white washing with lime |
| 72 | 13.80:Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 73 | 13.82.2:Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound) content less than 50 grams/ litre, of approved brand and manufacture including applying additional coats wherever required, to achieve even shade and colour.Two coats |
| 74 | 13.85.3:Applying priming coats with primer of approved brand and manufacture, having low VOC ( Volatile Organic Compound) content.With water thinnable cement primer on walls surface having VOC content less than 50 grams / litre |
| 75 | 22.23A:Providing & Applying polymer modified, flexible cementatious negative side waterproofing coating with elastic waterproofing polymers on interior wall plaster surface in three coats @14.35 kg /10 sqm. one coat of self priming of cementatious waterproofing polymer(dilution with water in the ratio of 1:1) and two coats of cementatious waterproofing polymer (dilution with water in the ratio of 3:1 ) after scrapping and properly cleaning the surface to remove pre-existing paint film & loose particles till plaster is visible, complete in all respect as per the direction of Engineer-in-Charge. |
| 76 | 9.117.1:Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1 mm), with wall thickness 2.0mm (±0.2 mm), corners of the door frame to be jointed with galvanized brackets and stainless steel screws, joints mitred and plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 x 19 mm and 1 mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer's specification and direction of Engineer-in-chargeExtruded section profile size 48x40 mm |
| 77 | 9.118.1:Providing and fixing to existing door frames24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness,fixed to the shutter styles by means of plastic/galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-in-charge( For W.C. and bathroom door shutter). |
| 78 | 9.147B.1:Providing and fixing factory made uPVC white colour fixed glazed windows/Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.) |
| 79 | 11.41.2:Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4(1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600 x 600 mm. |
| 80 | 11.46.2:Providing and laying Vitrified tiles indifferent sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete.Size of Tile 600x600 mm |
| 81 | 11.40:Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer) of Ist quality conforming to IS: 15622 of approved make in all colours, shades, except white, Ivory, Grey Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand) including pointing the joints with white cement and matching pigments etc., complete. |
| 82 | 8.31:Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in- Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 83 | 10.28:Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) |
| 84 | 12.45.4:Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with:Fully Perforated Gypusm Plaster Board of size 1200 x 2400 x 12.5 mm having approx. 15% perforated area with perforation size and pattern as approved by the Engineer - in- charge and as per manufacturer's specification, with all 4 side tapered and backed by acoustical tissue with NRC value not less than 0.60. |
| 85 | 50.18.7.3.2:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 25 mm dia 10Kgf/ cm2- Internal work- Exposed on wall |
| 86 | 50.18.7.6.2:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing . This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge 50 mm dia 6 Kgf/cm2 - Internal work- Exposed on wall |
| 87 | 50.18.8.9.1:Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work, including cutting chased and making good the wall etc. 110 mm pipe 6kgf/cm2 |
| 88 | 50.18.9.21.3:Providing and fixing PVC moulded fittings / accessories for Rigid PVC pipes, including jointing with PVC solvent cement -75 mm dia Door Elbow |
| 89 | 50.18.9.21.5:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement -75x75x75 mm dia Tee |
| 90 | 50.18.9.22.12:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110x75 mm dia Reducer |
| 91 | 50.18.9.22.2:Providing and fixing PVC moulded fittings / accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 110 mm dia 45 degree Elbow |
| 92 | 50.18.9.22.4:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement- 110 mm dia Bend |
| 93 | 50.18.9.22.5:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes including jointing with PVC solvent cement 110x110x110 mm dia Tee |
| 94 | 18.15.1:Providing and fixing brass bib cock of approved quality :15 mm nominal bore |
| 95 | 18.15.2:Providing and fixing brass bib cock of approved quality :20 mm nominal bore |
| 96 | 17.31:Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 97 | 17.7.4:Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap |
| 98 | 17.71:Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms |
| 99 | 17.73.1:Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm. weighing not less than 170 gms |
| 100 | 17.78:Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/6 litre (adjustable to 4 litre /8 litres), including seat cover, and cistern fittings, nuts bolts and gasket etc complete. |
| 101 | 19.7.1.1:Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand) with R.C.C. top with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix ( 1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size,) inside plastering 12 mm thick with cement mortar 1:3 ( 1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ) finished with a floating coat of neat cement complete as per standard design:Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weigh of cover 23 kg and weight of frame 15 kg):With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 102 | 17.29:Providing and fixing 100 mm sand cast Iron grating for gully trap. |
| 103 | 17.4.1:Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I. clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required:One urinal basin with 5 litre white P.V.C. automatic flushing cistern |
| 104 | 51.19.ST4:Supplying and installing ready made PVC Septic tank including the cost of carriage, trenching, placing at the level below ground level as specified as per the direction of engineer in charge (Provision for CC/RCC/Sand/06mm aggregate for the preparation of bed shall be paid separately) 4. 35 to 50 flush capacity |
| 105 | 18.48:Providing and placing on terrace (at all floor levels) polyethylene water storage tank :ISI 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 106 | OD294591/2025-2026:Supplying and fixing CP Health faucet good quality including cost of materials and labour charges etc. complete as per the direction of site engineer-in- charge. The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space and removal of debris from work site etc. |
| 107 | OD294592/2025-2026:Providing and fixing PVC moulded fittings/ accessories for Rigid PVC pipes, including jointing with PVC solvent cement - 150 mm dia floor trap The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space and removal of debris from work site etc. for all heights, complete as per the direction of engineer in charge. |
| 108 | OD294593/2025-2026:Providing and fixing C.P. brass angle valve for wash basin, water closset etc of approved quality conforming to IS: 8931 15 mm nominal bore The rate inclusive of all material charge, labour, transportation, Scaffolding (If needed) loading/unloading at the work space and removal of debris from work site etc. for all heights, complete as per the direction of engineer in charge. |
| 109 | OD308448/2025-2026:Lettering with vinyl sticker type letter of standard size, font and colour as specified by the Engineer in charge. |
| 110 | OD308449/2025-2026:Providing and fixing braille directional signage with ADA Braille sign in Polymer sheet with tactile characters and picture. 2 mm thick of standard size round, square or triangle in shape fixed by foam tape mounting including cost of materials and fixing charges etc complete |
| 111 | OD308450/2025-2026:Providing and fixing braille pictogram signage with Aluminium backed acrylic sheet with tactile characters and picture. 2 mm thick of standard size round, square or triangle in shape fixed by foam tape mounting including cost of materials and fixing charges etc complete |
| 112 | OD308451/2025-2026:Providing and fixing office signage boards with good quality 4mm thick ACP sheet afapproved colour as directerd by the Engineer in charge and indicating necessary signs and lettering etc with vinyl sticker type letters and necessary provisions for hooks/chains/rings/screws etc including cost of materials, conveyance and fixing charges etc complete |
| 113 | OD308452/2025-2026:Providing and fixing signage with vinyl sticker type sheet including printing ncecessary emblems of standard size, font and colour as specified by the Engineer in charge |
| 114 | OD308453/2025-2026:Providing and fixing U- shaped moveable stainless steel grab bar of standrad lenght and approved make as per the direction of Engineer in charge for providing in toilets and urinals for using the persons with disabilities including cost of materials, fixing charges etc |
| 115 | OD308454/2025-2026:Providing and fixing L-shaped stationary stainless steel grab bar of standrad lenght and approved make as per the direction of Engineer in charge for providing in toilets and urinals for using the persons with disabilities including cost of materials, fixing charges etc |
| 116 | OD308455/2025-2026:Providing and fixing special type chest support stainless steel grab bar for urinals in which the front bar have 100mm long for chest suppoert and side U shaped bars of length 600mm is provided for user to hold on while standing etc including cost of materials and conveyance etc |
| 117 | OD308456/2025-2026:Providing and laying Self Adhesive Polyurethane/Thermoplastic Elastomer Tactile Tiles of size 300X300mm in any colour for Hazard (Dots) & Directional (Lines) for visually impaired persons having size of 300x300x2 mm at base and 6.5 mm at projected area of Dash and Dots including cost of all materials and labour charges etc. |
| 118 | 4.1.A.1:Granular Sub-base with Well Graded Material (Table 400.1) (A) By Mix in Place Method Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401. (i) For Grading I Material |
| 119 | ELECTRICAL WORKS COMMUNITY HALL |
| 120 | OD365394/2025-2026:VDB1:6 way TPN double door Vertical DB for fixing 4P 63A Isolater as incomer 1 no. and 25A TP MCBs - 3nos,16A MCB-1No,10A TP MCB-2No.s as outgoings. |
| 121 | OD365391/2025-2026:6 way TPN double door DB for fixing 4P 25A RCBO 30mA as incomer 1 no. and 6 SP MCBs - 18 nos as outgoings. |
| 122 | 1.10.3:Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVCinsulated copper conductor single core cable in surface / recessed medium class PVC conduit,with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLSPVC insulated copper conductor single core cable etc as required.Group C |
| 123 | OD365390/2025-2026:IP 44 enclosure and 3P/4P 6A to 32A MCB |
| 124 | 1.14.1:Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2x1.5 sq.mm + 1x1.5 sq.mm earth wire |
| 125 | 1.14.2:Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire |
| 126 | OD363772/2025-2026:LED TUBE LIGHT SET 40W |
| 127 | OD363773/2025-2026:SUPPLY INSTALLATION OF LED DOWN LIGHT 40W |
| 128 | OD294525/2025-2026:Supply, installation, testing and commissioning of 150 mm sweep exhaust fan complete with louvers and other fixing accessories as required. |
| 129 | OD335240/2025-2026:Supply and fixing of signages 12x4\\" in size 3mm thick foam board with auto glow material |
| 130 | 19.1:Supply, installation, testing and commissioning of 1200 mm sweep BEE-5 star rated ceiling fan with brushless direct current motor (BLDC) , class of insulation B , 3 no:s blades , 30 cm long down rod , 2no:s canopies, shackle kit, safety rope , copper winding, power factor not less than .9, service value (CM/M/W) minimum 6.00, Air delivery minimum 210 cum/min,350 RPM (tolerance as per IS :374-2019, THD less than 10% remote or electronic regulator unit for speed control and all remaining accesories including safety pin, nut and bolts , washers, temperature rise equal to 75 deg celsius ( maximum) , insulation resistance more than 2 Megaohm , suitable for 230V,50 Hz, single phase AC supply , earthing etc., complete as required: |
| 131 | OD365275/2025-2026:16A socket outlets Supply and wiring for 16A modular type power plug socket controlled with 16 A modular type switch in same sswitch board mounted on a suitable factory built MS box and wiring using two runs of 2.5 sq.mm 1.1KV grade FRLS PVC insulated copper wire and earthing using 1 run 1.5 sq.mm green copper wire (including circuit mains) continuously run as per IS through ISI marked 20/25mm medium guage rigid PVC conduits, giving interconnections etc complete as required and as directed by engineer in charge. |
| 132 | OD365277/2025-2026:6A socket outlets (independent position)Supply and wiring for 6A plug points in independent positions using two runs of 1.5 sq.mm FRLS PVC insulated copper conductor single core stranded wire and 1.5 sqmm green copper wire as earth, including circuit mains and fixing 6A modular type shuttered universal plug socket controlled by 6A switch with moulded front plate, housed in a suitable MS box. Giving connections, earthing as detailed above etc complete as required. |
| 133 | OD365278/2025-2026:EARTHING CONDUCTORS.Supply, Laying & clamping at site of Copperearthing conductors inclusive of providing earthing terminations and bracing of the terminations etc.Supply and laying of following size copper earth strip / wire through walls, trench etc. Including giving terminationsNo.4 SWG |
| 134 | OD365279/2025-2026:EARTHING CONDUCTORS.Supply, Laying & clamping at site of Copperearthing conductors inclusive of providing earthing terminations and bracing of the terminations etc.Supply and laying of following size copper earth strip / wire through walls, trench etc. Including giving terminationsNo.10 SWG |
| 135 | OD365280/2025-2026:PIPE EARTH STATION.Supply of ISI marked Nickel Sealed Copper Bonded Rod Having Diameter of 32 mm with a minimum length of 3 Meter and an average Copper Coating Thickness of 250 microns Having Tinned Vertical Strip (Vstrip)/plate of dimension 150mm x 50mm X5mm with stainless steel 304 grade fasteners which is surrounded by IEC 62561-7, TCLP and RoHS Certified Earth Enhancing Compounds of minimum 40 kgs in a 8\\" Diameter Earth pit and the whole arrangement is enclosed by UV treated PVC Earth Pit Chamber of top dimensions 24cm x 24cm having minimum weight bearing Capacity of 25kN. |
| 136 | 90.12.7.40:Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.4 core 10 sq mm with factory made clamp |
| 137 | 90.12.7.42:Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.4 core 25 sq mm with factory made clamp |
| 138 | 9.1.32:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 10 sq. mm (25mm) |
| 139 | 9.1.34:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 25 sq. mm (28mm) |
| 140 | OD375336/2025-2026:4 WAY ENCLOSERIP 66 enclosure and 3P/4P 6A to 32A MCB |
| 141 | OD375338/2025-2026:EARTHING CONDUCTORS.Supply, Laying & clamping at site of Copper earthing conductors inclusive of providing earthing terminations and bracing of the terminations etc.Supply and laying of following size copper earth strip / wire through walls, trench etc. Including giving terminations25 x 3 mm copper |
| 142 | OD375339/2025-2026:METER PANEL (WHETHERPROOF)Bottom cable entry for incoming and outgoing feeders. Fabricated out of 16SWG CRCA sheet1) Busbars:150A TPN Al. Busbar - 1no.Earth bus - 25 x 3mm CU.2) Incomer1:63 A Cut-off fuse base - 3 NOSControl HRC fuse - 3 nos3) Outgoings:63 A 4P MCCB 25kA Ics -1 no |
| 143 | ELECTRICAL ESTIMATE CREMATORIUM |
| 144 | OD374905/2025-2026:Supply, delivery, and installation of Three Phase DG SET with Manual Start Control Panel and alternator suitable for continuous operation rated 25 kVA / 20KW (30.5HP) at 1500 rpm, 415 V, 0.8 PF, 50. Hz, 3 Ph. in SPDP enclosure, self-excited, self-regulated Brush less. The alternator conforms to IS:4722, BS EN 60034-1 and will be suitable for tropical condition. Diesel engine conforms to present CPCB IV+ norms.The walls of enclosure are insulated with the fire-retardant & noise absorbent foam/rock wool so as to comply with the noise level of 75dB(A) at distance of 1meter in open free field environment as per ISO 8528 part 10 specified by ministry of Environment & Forest. The Control Panel is manufactured with CRCA sheet and is powder coated for a weather-proof and long lasting finish. The Control Panel consists of Microprocessor based genset controller, MCB of suitablerating, Push Button (starter), LED Battery Charging alternator fail indication, Current Transformers, Instrument fuses etc complete as per KSEI Specifications. The Genset controller has all the basic safeties and protections. Daily service fuel tank 55 liters manufactured with sheet metal complete with drain valve, air vent, inlet and outlet connection. BATTERY: 12 V |
| 145 | OD416561/2025-2026:63 AMP COS WITH 4 WAY VDBSupply, installation, testing and commissioning of 4 Way VTPN DB with ENCLOSER(a) Incomer : 63 A 4P COS with door interlock & ROM - 1 no.(b) Incomer : 63 A 4P Isolater with door interlock & ROM - 1 no. (c ) Outgoing :1. 40 A TP MCB - 2 nos2. 32 A TP MCB - 2 nosIndication Lamps :1. LED type R,Y,B coloured indication lamps on the incoming side - 3 nos.32A Bakelite fuse carrier & bases with 2A HBC fuses :1. For Indication Lamps at the incomer - 1 set (3 nos.) |
| 146 | OD436215/2025-2026:6 way TPN double door Vertical DB for fixing 4P 32A Isolator as incomer 1 no. and 6A TP MCBs - 5 nos,16 A TP MCB-1 No. as outgoings. |
| 147 | OD374826/2025-2026:4 way TPN double door DB ,including4P 40A RCBO 30mA as incomer 1 no. and 6A SP MCBs - 12 nos as outgoings. |
| 148 | OD374824/2025-2026:IP 44 enclosure and 3P/4P 6A to 32A MCB |
| 149 | 1.11:Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. |
| 150 | OD374783/2025-2026:16A socket outlets Supply and wiring for 16A modular type power plug socket controlled with 16 A modular type switch in same sswitch board mounted on a suitable factory built MS box and wiring using two runs of 2.5 sq.mm 1.1KV grade FRLS PVC insulated copper wire and earthing using 1 run 1.5 sq.mm green copper wire (including circuit mains) continuously run as per IS through ISI marked 20/25mm medium guage rigid PVC conduits, giving interconnections etc complete as required and as directed by engineer in charge. |
| 151 | OD374785/2025-2026:6A socket outlets (independent position)Supply and wiring for 6A plug points in independent positions using two runs of 1.5 sq.mm FRLS PVC insulated copper conductor single core stranded wire and 1.5 sqmm green copper wire as earth, including circuit mains and fixing 6A modular type shuttered universal plug socket controlled by 6A switch with moulded front plate, housed in a suitable MS box. Giving connections, earthing as detailed above etc complete as required. |
| 152 | OD374787/2025-2026:EARTHING CONDUCTORS.Supply, Laying & clamping at site of Copperearthing conductors inclusive of providing earthing terminations and bracing of the terminations etc.Supply and laying of following size copper earth strip / wire through walls, trench etc. Including giving terminationsNo.10 SWG |
| 153 | OD446741/2025-2026:EARTHING CONDUCTORS.Supply, Laying & clamping at site of Copperearthing conductors inclusive of providing earthing terminations and bracing of the terminations etc.Supply and laying of following size copper earth strip / wire through walls, trench etc. Including giving terminationsNo.6 SWG |
| 154 | OD374788/2025-2026:PIPE EARTH STATION.Supply of ISI marked Nickel Sealed Copper Bonded Rod Having Diameter of 32 mm with a minimum length of 3 Meter and an average Copper Coating Thickness of 250 microns Having Tinned Vertical Strip (Vstrip)/plate of dimension 150mm x 50mm X5mm with stainless steel 304 grade fasteners which is surrounded by IEC 62561-7, TCLP and RoHS Certified Earth Enhancing Compounds of minimum 40 kgs in a 8\\" Diameter Earth pit and the whole arrangement is enclosed by UV treated PVC Earth Pit Chamber of top dimensions 24cm x 24cm having minimum weight bearing Capacity of 25kN. |
| 155 | 1.14.1:Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2x1.5 sq.mm + 1x1.5 sq.mm earth wire |
| 156 | 1.14.2:Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire |
| 157 | 9.1.32:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 10 sq. mm (25mm) |
| 158 | 90.12.7.40:Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.4 core 10 sq mm with factory made clamp |
| 159 | 90.12.7.41:Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.4 core 16 sq mm with factory made clamp |
| 160 | 90.12.7.42:Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.4 core 25 sq mm with factory made clamp |
| 161 | 9.1.33:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 16 sq. mm (28mm) |
| 162 | 9.1.34:Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 25 sq. mm (28mm) |
| 163 | OD375330/2025-2026:Earth BenchSupply and clamping 25 x 3 mm tinned Cu. Earth bench of following lengths on the surface of wall for connecting earth continuity leads at required locations.60 cm Earth Bench |
| 164 | OD375333/2025-2026:EARTHING CONDUCTORS.Supply, Laying & clamping at site of Copper earthing conductors inclusive of providing earthing terminations and bracing of the terminations etc.Supply and laying of following size copper earth strip / wire through walls, trench etc. Including giving terminations25 x 3 mm copper |
| 165 | OD375334/2025-2026:METER PANEL Bottom cable entry for incoming and outgoing feeders. Fabricated out of 16SWG CRCA sheet1) Busbars:150A TPN Al. Busbar - 1no.Earth bus - 25 x 3mm CU.2) Incomer1:63A Cut-off fuse base - 3 nosControl HRC fuse - 3 nos3) Outgoings:63A 4P MCCB 25kA Ics-1 no |
| 166 | OD374841/2025-2026:LED TUBE LIGHT SET 40W |
| 167 | OD374842/2025-2026:SUPPLY INSTALLATION OF LED DOWN LIGHT 40W |
| 168 | 19.1:Supply, installation, testing and commissioning of 1200 mm sweep BEE-5 star rated ceiling fan with brushless direct current motor (BLDC) , class of insulation B , 3 no:s blades , 30 cm long down rod , 2no:s canopies, shackle kit, safety rope , copper winding, power factor not less than .9, service value (CM/M/W) minimum 6.00, Air delivery minimum 210 cum/min,350 RPM (tolerance as per IS :374-2019, THD less than 10% remote or electronic regulator unit for speed control and all remaining accesories including safety pin, nut and bolts , washers, temperature rise equal to 75 deg celsius ( maximum) , insulation resistance more than 2 Megaohm , suitable for 230V,50 Hz, single phase AC supply , earthing etc., complete as required: |
| 169 | OD375294/2025-2026:Supply and installation of 150 mm sweep exhaust fan |
| 170 | OD375321/2025-2026:Supply and fixing of approved make Carbon-di-oxidetype Fire extinguishers of 4.5 Kg capacity, Co2 gasfilled in brand new seamless cylinder with powdercoated finish, made out of Manganese steel, withwheel type valve, discharge nozzle, bend & horn wallmounting bracket etc., confirming to IS:15683 |
| 171 | OD375322/2025-2026:Supplying, and fixing of Dry chemical powder type fireextinguisher of 4 Kgs. Capacity, with initial filling inbrand new cylinder with powder coated finish, fittedwith Gun metal union, discharge hose, wall mountingbracket etc. complete, confirming to IS:15683. Please Enable Macros to View BoQ information |
| SR No | FileName | File Description |
| 1 | Click here to download tender document | Tender Documents |
| 2 | Click here to download tender document | Tender Documents |
| 3 | Click here to download tender document | Tender Documents |
| 4 | Click here to download tender document | Tender Documents |
| 5 | Click here to download tender document | Tender Documents |
| 6 | Click here to download tender document | Tender Documents |
We are a group of professionals specializing in custom software development, web development, mobile app development, IOT base solutions, web design, graphics & Enterprise solutions provid.
Copyright © 2026 · All Rights Reserved. Terms of Usage | Privacy Policy
For Tender Information Services Visit : TenderDetail
