|
| 1 | CIVIL WORKS- Demolishing, Centering & Shuttering, Concreting Work for fixing C GROOVE, SEAL TRACK and SILL BEAM. |
| 2 | OD52481/2025-2026:RING BUND Type-I-Putting up ring bund as per approved shape 2.5m bottom width, 1m top width using empty gunny/polythene bags filled with earth placed in 2 rows at 0.6m apart and filled in between with puddle clay to form bund for an average height 2.00m including labour dismantling the bund after completion of the work etc. complete. |
| 3 | 15.2.1:Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 4 | 4.3.3:Centering and shuttering including strutting, propping etc. and removal of form work for:Columns, piers, abutments, pillars, posts and struts |
| 5 | 5.22.5:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelHard drawn steel wire fabric |
| 6 | 4.1.2:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:1½:3 (1 Cement: 1½ coarse sand (zone-III) derived from natural sources : 3graded stone aggregate 20 mm nominal size derived from natural sources) |
| 7 | 5.2.2:Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up tot floor five level excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 8 | 13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) |
| 9 | OD53008/2025-2026:DRILLING (up to depth of 200mm for MS/SS/TMT rod dia. 8mm to 25mm) and FASTENING with MS/SS/TMT rod in concrete/Stone including conveyance and labor charges complete.[excluding cost of materials already supplied |
| 10 | OD53009/2025-2026:Anchoring the MS/SS rebars into the drilled hole using CHEMICAL ADHESIVES, including cost of hire charge of machine, cost of chemical adhesive and labour |
| 11 | MS SHUTTERS-SUPPLY, FABRICATION, PAINTING and ERECTION of embedded parts, shutter, hoisting mechanism and hoisting bridge. |
| 12 | OD19036/2025-2026:Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges |
| 13 | OD19031/2025-2026:Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges |
| 14 | OD19039/2025-2026:Supply of MS round bar including cost of conveyance charges |
| 15 | 85.103:Supply of MS checquered plates including cost of conveyance charges |
| 16 | OD52322/2025-2026:SUPPLYING and STACKING OF 32mm GI Pipe (NB :32mm , OD: 42.2mm to 42.9mm) as per IS 1239 including cost of all materials and conveyance. |
| 17 | OD19462/2025-2026:Supply of SS BOLT and NUT up to 300mm Length including cost of conveyance. |
| 18 | OD19038/2025-2026:Fabrication and errection of Embedded parts for canal shutters ( lJp to 2 tonne weight ) and accessories as per approved specifications, drawings and directions of deptl fficer at site including cost of labour,machinery, all leads and lifts, incidental and handling charges etc complete but excluding cost of material already supplied. |
| 19 | OD19043/2025-2026:Fabrication and supply of Structural steel canal shutters ( Up to 2 tonne weight ) /Hoisting Bridge /Platform and accessories etc. for the same as per approved specifications, drawings and directions of deptl fficer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc complete but excluding cost of material already supplied |
| 20 | OD19033/2025-2026:Fabrication,Supply,Erection and Assembling in correct position and alignment by welding SS Embedded parts in 304L Grade like roller track,seal track,Seal seat etc as per approved specifications,drawings and directions of deptl officer at site including cost of all materials,labour,machinery for planing,welding,shearing,grinding etc,lead and lift,conveyance,incidental and handling etc complete |
| 21 | 85.116:Supplying and fixing in correct position with specified initial interface the flat type rubber seal confirming to IS 11855 to the gates including cost of SS bolts and nut all labour and machinery and incidental and conveyance charges complete as per approved specification and drawing |
| 22 | 85.118:Supplying and fixing in correct position with specified initial interface L-type / bulb nose rubber seal confirming to IS11855 to the gates including cost of SS bolts and nuts and all labour and machinery and incidental and conveyance charges complete as per approved specifications and drawings |
| 23 | 85.114:Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc on dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350 microns after cleaning the surface using hand and power tool cleaning including cost of all materials, labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site |
| 24 | 85.115:Cost of painting with 2 coats of enamel paint over 1 coat of zinchromate primer as per IS1477:1994 after hand and power tool cleaning including cost of all materials, labour charges, cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site |
| 25 | OD19035/2025-2026:Providing EN-8 Screw Rod 7.50 Tonne Capacity 4.00 Mtr lift Screw Rod having one number of EN-8 Screw Shaft having a lifting speed of around 5.00 cm/min for 24 rpm of hand operation including cost of all material, labour, hire charges and conveyance. (63mm Dia Screw rod ) |
| 26 | OD19468/2025-2026:Providing of Double worm and pinion having a lifting speed of around 5.00 cm/min for hand operation. having gearbox wall thickness of 12mm for side, 16mm for top and 24mm base. Top plate fixed with minimum 8 nos of M12 bolt , including cost of Mechanical stoper, Locking arrangement, Operating handle and all other materials, labour, hire charges and conveyance. |
| 27 | OD52992/2025-2026:PROVIDING of WORM and PINION having a lifting speed of around 5.00 cm/min for hand operation. having gearbox wall thickness of 12mm for side, 16mm for top and 24mm base. Top plate fixed with minimum 8 nos of M12 bolt , including cost of Mechanical stoper, Locking arrangement, Operating handle and all other materials, labour, hire charges and conveyance. |
| 28 | OD19474/2025-2026:PROVIDING BASE & NUT arrangement for hoisting the shutter including cost of all materials labour etc complete., |
| 29 | OD19032/2025-2026:Re-Conditioning of existing EN-8 Screw rod including cost of all materials, labour charges, hire charges, energy charges, conveyance, all leads and lifts etc. complete. |
| 30 | OD19044/2025-2026:Dismantaling of the shutters (where there is road acess to the point ) from the grooves and stacking including cost of all machinery, labour all incidental and conveyance charges etc complete as per direction of departmental officer at site (Weight of the unserviceable shutters and embedded parts may be calculated as 60% and unserviceable hoisting units as 80%) .. |
| 31 | OD19034/2025-2026:Hire Charges of diesel generator set at site (Maintenance of Canal Shutters). |
| 32 | OD19042/2025-2026:Providing screw rod locking arrangement to the shutters including cost of materials ,fixing charges etc complete |
| 33 | OD53002/2025-2026:OVERHAULING OF EXISTING WORM AND PINION including cost of all materials,labour,hire charges, energy charges,conveyance and all leads and lifts for CANAL SHUTTER., |
| 34 | OD19041/2025-2026:SUPPLYING and APPLYING GREASE on NEW SCREW ROD for CANAL GATE |
| 35 | OD19037/2025-2026:SUPPLYING and STACKING of PAD LOCK. |
| 36 | OD53006/2025-2026:Erection of the Canal Shutter ( Up to 2 Tonne weight ) / Hoisting Bridge / Platform including hand rails , ladder etc. for the same including . alignment correcting and setting complete including cost of all labour, machinery, incidental and conveyance , lead and lift charges etc complete but excluding cost of materials already supplied., Please Enable Macros to View BoQ information |
