|
| 1 | DISMANTLING metal parts, DEMOLISHING structures, FORM WORK, REINFORCED CEMENT CONCRETE and PLASTERING. |
| 2 | OD19342/2025-2026:Dismantling of the Canal Shutter ( Up to 2 Tonne weight ) / Hoisting unit / Embedded parts etc. of the same and stacking at a distance of 100 meter including hire of machinery, labour etc. complete as directed by the departmental officer at the site. (Weight of the unserviceable shutters and embedded parts may be calculated as 60 % and unserviceable hoisting unit as 80%). |
| 3 | 15.2.1:Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 4 | 2.6.1:Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.All kinds of soil |
| 5 | 2.25:Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m. |
| 6 | 5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete |
| 7 | 5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more |
| 8 | 5.1.2:Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 9 | 13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) |
| 10 | SUPPLY, FABRICATION, PAINTING AND ERECTION OF EMBEDDED PARTS, SHUTTER, HOISTING MECHANISM AND HOISTING BRIDGE |
| 11 | OD19355/2025-2026:Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges. |
| 12 | OD19345/2025-2026:Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges. |
| 13 | OD19356/2025-2026:Supply of MS round bar including cost of conveyance charges. |
| 14 | OD19350/2025-2026:Supply of BOLT and NUT up to 300mm Length including cost of conveyance. (Data for 1Qtl) |
| 15 | OD19357/2025-2026:Fabrication, Supply, erection and assembling in correct position and alignment by welding SS Embedded parts in 304L Grade like roller track, seal track, Seal seat etc. as per approved specifications, drawings and directions of deptl. officer at site including cost of all materials, labour, machinery for planing, welding, shearing, grinding etc., lead and lift, conveyance, incidental and handling etc. complete |
| 16 | OD19348/2025-2026:Fabrication and erection of Embedded parts of Canal shutters ( Up to 2 tonne weight ) and accessories as per approved specifications, drawings and directions of deptl officer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc complete but excluding cost of material already supplied. |
| 17 | OD19349/2025-2026:Fabrication and supply of Structural steel canal gate ( Less than 2 tonne weight ) and accessories as per approved specifications, drawings and directions of deptl officer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc complete but excluding cost of material already supplied. |
| 18 | OD19359/2025-2026:Supplying and fixing in correct position with specified initial interface the flat type rubber seal confirming to IS 11855 to the gates including cost of SS bolts and nut all labour and machinery and incidental and conveyance charges complete as per approved specification and drawing |
| 19 | OD19358/2025-2026:Supplying and fixing in correct position with specified initial interface L-type / bulb nose rubber seal confirming to IS11855 to the gates including cost of SS bolts and nuts and all labour and machinery and incidental and conveyance charges complete as per approved specifications and drawings. |
| 20 | OD19347/2025-2026:Providing base and nut arrangement for hoisting the shutter including cost of all materials labour etc complete. |
| 21 | OD19351/2025-2026:Providing EN-8 screw rod 7.50 tonne capacity 4.00 M lift screw hoist having one number of EN -8 scerw shaft,worm gear units having a lifting speed of around 5.00 cm/min for 24 rpm of hand operation including cost of all materials, labour, hire charges and conveyance. 1m Screw rod, dia 67mm with single start square thread with head pitch of 12.7mm, root dia 62.3mm EN-8 shaft |
| 22 | OD19346/2025-2026:THREAD LESS portion of the screw rod (per metre rate). |
| 23 | 85.114:Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc on dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350 microns after cleaning the surface using hand and power tool cleaning including cost of all materials, labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site |
| 24 | OD19352/2025-2026:Erection of the Canal Shutter ( Up to 2 Tonne weight )/Hoisting Bridge etc. for the same including alignment correcting and setting complete including cost of all labour, machinery, incidental and conveyance , lead and lift charges etc complete but excluding cost of materials already supplied. |
| 25 | OD19353/2025-2026:SUPPLYING and APPLYING GREASE on NEW SCREW ROD for CANAL GATE (Data for 1m) Please Enable Macros to View BoQ information |
