Name of Work:- RENOVATION OF ELECTRIC FURNACE NO.-1 AND ALLIED WORKS AT DHAPA HUMAN CREMATORIUM.
Sl. No.
Item Description
1
REMOVING OF STACK: Removing the broken bricks & all rubbishes to outside crematory/ dumping ground incl. loading, unloading, stacking & cost for transportation during patch repairing purpose .
2
CLEANING AND REPAIRING OF FUEL DUCT PASSAGE:Removing the complete damaged R.S bricks and R.S slab of the (U.G) duct passage of the furnace chamber and thorough cleaning of the duct passage upto the start of brick build chimney by removing ash/carbon particles and relining the same with R.S Slabs & R.S bricks after mending good damages in the duct passages with insulation brick and red brick (1:4) with all necessary cementing masonry work
3
PATCH WORK WITH BRICKS: Good quality fire clay mortar Washing of the entire chamber with Sodium Siliminate clay should be necessary.
4
CONSTRUCTION OF DOOR BLANKET: a) Supply, Fixing the S.S304 spike from inside the furnace door each of 280mm dia for holding the ceramic blanket
5
HEATING ELEMENT: Supply and fixing the Heating element (Heatcomake) of capacity 4.5 K.W to be working in supply voltage of 240 V 50 Hz made from 80/20 Nicrome wire of 8 SWG in coiled coil from welded S.S stud on both ends. The coil should be inserted into the groove of existing coil brick after proper cleaning and the S.S Studs housed into the ceramic caller tube wrapped. With asbestos rope for tight fitting and sealing as heat proof extended S.S stud to be connected brass/ copper connector with complete connection in all respect of existing system.
6
THERMOCOUPLE: a) Supply and fixing the thermocouple of heat sensing range 0-1200 deg. C having (Cr-A1) sensor house in S. Sd 304 casing of dimension 1200 mm long x 22 mm OD complete encased in to it and fitted terminal on other end for connection of compensating wire. Heatco make
7
HEATING ELEMENT: Supplying and fixing the terminal connector having drill holes for inserting S.S stud of 8.5 mm dia and connection point of existing copper wires of overall dimension 80mm long x25mm square shape.
8
CLEANING AND REPAIRING OF FUEL DUCT PASSAGE: Supply &Fixing of R.S. slab after removing the same with necessary fire clay mortar.
9
ALTER (WITH BRICKS M.K.92): Construction of Alter in front of furnace chamber flash to furnace door inside with M.K ...92 fire bricks with good quality fire clay mortar
10
FRONT COVER OF FURNACE DOOR: Supplying and fixing the new cover made of from 3.15 mm (10 SWG) CRCA sheet over all dimension 2400 mm X 1200mm with top arched shape as per existing drill holes for fixing over the furnace door in two halves. R.H Side
11
FRONT COVER OF FURNACE DOOR: Supplying and fixing the new cover made of from 3.15 mm (10 SWG) CRCA sheet over all dimension 2400 mm X 1200mm with top arched shape as per existing drill holes for fixing over the furnace door in two halves. L.H Side
12
BACK COVER OF FURNACE DOOR: Supplying and fixing the new cover made of from 3.15 mm (10 SWG) CRCA sheet over all dimension 2400 mm X 1200mm with top arched shape as per existing drill holes for fixing over the furnace door in two halves. R.H Side
13
Sub Total
14
GST 18%
15
CESS 1% Please Enable Macros to View BoQ information
We takes all possible care for accurate & authentic tender information, however Users
are requested to refer Original source of Tender Notice / Tender Document published by
Tender Issuing Agency before taking any call regarding this tender.
