|
| 1 | Clearing and grubbing road land including uprooting rank vegetation, grass, bushes, shrubs, saplings and trees girth up to 300 mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, up to a lead of 1000 meters including removal and disposal of top organic soil not exceeding 150 mm in thickness as per technical specification and direction of Engineer-in-Charge. |
| 2 | Scarifying the existing bituminous road surface to a depth of 50mm (By Mechanical means) and disposal of scarified material within all lifts and lead upto 1000m and as per direction of the Engineer-in-Charge. |
| 3 | Reworking the scarified bituminous surface after supplementing the base materials with sand and water compacting with PRR including hire and running charges of PRR cost, conveyance, royalty of all materials, labour charges, T&P etc. required for the work complete as per specification and direction of the Engineer in charge. |
| 4 | Earth work in excavation of foundation trenches in hard soil within initial lead and lift including dressing and leveling the bed upto the required depth and depositing the excavated materials away from the working area etc.complete as per the specification and direction of the Engineer-in-charge. |
| 5 | Excavation for road work in soil with hydraulic excavator of 0.9 cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross-sections, and transporting to the embankment location with a lift upto 1.5m and lead upto 1000m as per Technical Specification Clause 302.3 of MoRD. |
| 6 | Construction of embankment with approved material obtained from borrow pits with all lifts & leads, transporting to site by mechanical means, spreading, grading to required slope and compacting to meet requirement of Tables 300.2 & clause 305 of MoRT&H specification for Road & Bridge works as per direction of the Engineer-in-Charge. |
| 7 | Supplying & filling good clean river sand of approved quality including watering to complete saturation & ramming complete with all leads & lifts including cost, conveyance, royalty of all materials & cost of all labour & T&P required for the work etc. complete as per specification & direction of Engineer in charge. |
| 8 | Construction of granular sub-base by providing Close Graded Granular sub-base Grading - III material as per table 400-1, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density complete with all leads & lifts including cost, conveyance, royalty of all materials & cost of all labour & T&P required for the work etc as per clause 401 of MoSRT&H Specifications for Road & Bridge works as per direction of the Engineer-in-Charge. |
| 9 | Providing, laying, spreading and compacting graded stone aggregates of specific sizes to wet mix macadam specification including premixing the material with water at OMC in mechanical mix plant carriage of mixed material by tipper to site, laying in uniform layers with paver in sub-base/ base course on well prepared surface and compacting with vibratory roller to achieve the desired density as per Technical Specification Clause 406 of MoSRT&H specification for road & bridge works (4th revision) including cost, conveyance, royalty, labour charges, T&P etc. required for the work complete as per specification and direction of the Engineer-in-Charge. |
| 10 | Providing and applying primer coat with bitumen emulsion (SS) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.60 kg/sqm using mechanical means for low porosity surface including cost, conveyance, royalty of materials, labour charges, T&P etc, required for the work complete as per clause 502 of MoRT&H specification and direction of Engineer in Charge. |
| 11 | Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.20 kg/sqm on the prepared bituminous / granular surfaces cleaned with mechanical broom as per Clause 503 of MoSRT&H specifications including cost, conveyance, royalty, labour charges, T&P etc. required for the work complete as per specification and direction of the Engineer-in-Charge. |
| 12 | Providing & laying compacted Bituminous Macadam (Grading - II ) using 60/70 grade Bitumen with Hot Mix Plant using crusher broken hard granite aggregates of specified grading premixed with bituminous binder @ 3.3 % by weight of total mix and filler, transporting the hot mix to works site, lying with Hydrostatic Paver Finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled vibratory and tandem rollers to achieve the desired compacting as per Clause No.106, 108, 111, 112, 501, 503 , 504 and section 900 of specifications for Road and Bridge works of Ministry of Road Transport & Highways (5th Revision) & including cost of all materials, labour, T&P, royalty etc complete in all respect and as per direction of the Engineer-in-charge. |
| 13 | Providing and laying semi dense bituminous concrete with batch type hot mix plant using crushed aggregates of 10mm nominal size (Grading-II) premixed with bituminous binder of 60/70 penetration grade of bitumen, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheelede,vibratory and tandem rollers to achieve the desired compaction as per Clause 508 of MoSRT&H Specifications for Road & Bridge works (4th Revision) including cost, conveyance, royalty, labour charges, T&P etc. required for the work complete as per specification and direction of the Engineer-in-Charge. |
| 14 | Construction of un-reinforced, plain cement concrete pavement, thickness as per design, over a prepared sub base, with 43 grade cement or any other type as per Clause 1501.2.2 M30 (Grade), coarse and fine aggregates conforming to IS:383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less than 0.2 cum capacity using approved mix design, laid in approved fixed side formwork (steel channel, laying and fixing of 125 micron thick polythene film, wedges, steel plates including levelling the formwork as per drawing), spreading the concrete with shovels, rakes, compacted using needle, screed and plate vibrators and finished in continuous operation including provision of contraction and expansion, construction joints, applying debonding strips, primer, sealant, near approaches to bridge/culvert and construction joints, admixtures as approved, curing of concrete slabs for 14-days, curing compound (where specified) and water finishing to lines and grade as per drawing and technical specification as per clause 1501 of MoRD and direction of Engineer in Charge. |
| 15 | Fine dressing and turfing including transportation by mechanical means with all leads and lifts and placing of turfs in position and ramming with thapies including watering and cost of labour and all materials etc.complete as per the direction of the Engineer-in-charge. |
| 16 | Providing plain cement concrete M-15 with clean black hard granite stone aggregates of 40mm & down graded size of approved quality from approved quarry consistent with strength & cover of concrete & laying in position in layers not exceeding 150mm thick in the proper packing by means of vibrator to proper slope and to the required level including hoisting lowering laying concrete providing side shuttering & finishing all exposed surface smooth supplying & working of pumps, labour & T&P articles & all machineries, dewatering if required with cost conveyance, royality of all materials complete in all respect as per specification & direction of the Engineer-in-Charge.In Foundation |
| 17 | In Substructure |
| 18 | RCC work M-25 grade as per approved designs and drawings having a minimum compressive strength (in work test) 250Kg / Sqm in 15 cm. cubes at 28 days after mixing and test conducted in accordance with I.S. 456 and I.S. 516 using 12 mm. to 20 mm. size black hard crusher broken granite stone chips and screened and washed sharp sand for mortar of approved quality from approved quarry, washed and cleaned (20 mm. size chips not to exceed 25 % ) to be mixed in concrete mixture with approved grade cement including hoisting, lowering, laying and compacting concrete by using vibrators, watering and curing for 28 days, centring and shuttering and finishing the exposed surface smooth providing grooves or beads wherever necessary including cost, conveyance, loading, unloading, royalties of all materials and cost of all labours, sundries, T&P, required for the work etc. complete in all respect but excluding cost and conveyance of Tor steel and binding wires and labour charges for straightening, cutting, bending etc. of steel tying the grills and placing in proper position as per direction of the Engineer in charge.Drain Cover Slab |
| 19 | Supply of HYSD bars confirming to grade Fe - 500 cutting bending, binding, lapping, splicing, welding etc. (conforming to IS 1786/1985 specification & jointing if necessary by lapping & tying the grills & placing in position as required for RCC works as per the approved design, hoisting, lowering & laying in position including cost & conveyance of tor steel & binding wires of 18 to 20 gauge(as to be approved by the Deptt.) etc. complete (weight of binding wire,laping shall not be considered for payment at all which will be borne by the contractor ) standard CO-efficient of different sizes of the steel shall be considered & welding & lapping should confirm to relevant clause of IRC-21/1987 as per direction of the Engineer in charge. |
| 20 | Rough stone dry packing in aprons & revetments with hard granite stone of 30cm.size & above having individual weight not less than 40kg. of approved quality from approved quarry including cost, conveyance, royality of all materials, cost of all labour including filling the interstics with small key stones by wedging & hammering & finishing to proper slope including dewatering & T&P articles etc. complete as per specification & direction of the Engineer-in-Charge. |
| 21 | Providing weepholes in brick masonry/Plain/Reinforced concrete abutment, wing wall/return wall with 100 mm dia AC pipes, extending through the full width of the structures with slope of 1(V):20(H) towards drawing face including cost, conveyance, royalty of materials, labour charges, T&P etc, required for the work complete as per specification and direction of Engineer in Charge. |
| 22 | Construction of embankment with approved materials deposited at site from roadway cutting and excavation from drain & foundation of other structures with all lead & lift by mechanical means graded and compacted to meet requirement of Tables 300.1 and 300.2 as per Technical Specification Clause 301.5 & MORD clause 301.5 as directed by Engineer in charge. |
| 23 | Providing & laying of hot applied thermoplastic compond 2.5mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35. The finished surface to be level, uniform & free from streaks & holes as per drawing and Technical Specifications of MoRT&H clause 803 and as per direction of Engineer-in-Charge. |
| 24 | Supplying and laying R.C.C. Hume pipes of NP3 class(confirming to relevant IS specification) for culverts including fixing collar with cement mortar 1:3 including cost, conveyance royality, labour, T&P,all other materials required for the work etc.complete as per direction of Engineer-in-charge.(i) 600 mm dia |
| 25 | (ii) 1000 mm dia |
| 26 | Providing and fixing of semi reflective cautionary, mandatory and informatory sign board as per IRC:67 made of 1.5 mm thick MS Sheet duly stove white colour in front and gray colour on back with red reflective border of 65 mm width and required letters and figures with reflective tape engineering grade as per Clause 1701.3.9 of MORD for Rural Roads of required shade and colour supported and welded on 47mm x 47 mm x 12 SWG sheet tube firmly fixed to the ground by mean of properly designed foundations with M-15 grade cement concrete 450x450x600 mm, 600 mm below ground level as per approved drawing Clause 1701.2.2 of MORD Specification for Rural roads including cost,conveyance,royalty, labour and T&P required for the work as per direction of the Engineer-in-Charge.i) 600mm equilateral triangle |
| 27 | ii) 600mm dia circular |
| 28 | Providing & fixing guard stones of M-15 grade guard /boundary stone /local stone of standard design as per IRC-25 fixed position as per drawing and Technical Specifications MORD clause 1704 and as per direction of Engineer-in-Charge. |
| 29 | Reinforced cement concrete M15 grade Kilometer stone of standard design as per IRC:8 fixing in position including painting & printing etc. as per the drawing &technical specification clause 1703 of MoRD and as per direction of Engineer-in-Charge.(i) 200 M Stone (Precast) |
| 30 | (ii) Ordinary kilometer stone (Precast) |
| 31 | Providing and erecting direction and place identification of semi reflective sign boards as per IRC-67 made of 2 mm thick M.S. Sheet duly stove enameled paint white colour in front and grey colour on back with reflective border of 70 mm width and required message, letters, figures, with reflective engineering grade tape as per MORD specifications of requied shade and colour as per clause no. 1701 of MORD specification for Rural roads and as per direction of the Engineer-in-Charge. Intermediate Logo Board |
| 32 | Providing and fixing of typical Citizens information board as per MORD specifications and drawing. Three MS Plates of 50 X 5 mm thick, back plate duly welded with 75mm dia steel tubes back on edges as per drawings. The lower & upper plate will be welded with MS flat iron frame of 50mm x 5mm. The steel tubes duly embeded in cement concrete M-15 grade blocks of 600mm x 600mm x 750mm below ground level. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per drawing Clause 1701 and Annexure 1700.1 |
| 33 | Providing and fixing of typical informatory sign board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6 mm thick, top and middle plate duly welded with MS flat iron 25mm x 5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mm x 25mm x 5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75 mm of 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All M.S. will be stove enameled on both sides. Lettering and printing arrows, border etc. will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy paint as per Clause 1701 and Annexure 1700.1 of MORD Specification for Rural roads including cost, conveyance, royalty, labour and T&P required for the work and as per direction of Engineer-in-charge. |
| 34 | Maintenance Restoration of Rain-cuts with soil, moorum gravel or a mixture of these, clearing the loose soil, benching for 300mm width laying fresh materials in layers not exceeding 250mm and compaction with plate compactor or power rammer to restore the original alignment, level and slopes as per clause 1902 of MORD specification for Rural roads by manual means and as per direction of Engineer-in -charge. 1st Year |
| 35 | 2nd Year |
| 36 | 3rd Year |
| 37 | 4th Year |
| 38 | 5th Year |
| 39 | Maintenance of Earthen shoulder (filling with fresh selected soil) Making up loss of materials/ irregularities of shoulders to the design levels by adding fresh approved selected soil and compacting it with appropriate equipment at OMC upto a lead of 1000m as per clause 1903 of MORD specification for Rural roads and as per direction of Engineer-in-charge. 1st Year |
| 40 | 2nd Year |
| 41 | 3rd Year |
| 42 | 4th Year |
| 43 | 5th Year |
| 44 | Maintenance of earthen shoulder Stripping of excess soil from the shoulder surface to achieve the approved level and compacting with plate compactor at OMC as per clause 1903 of MORD specification for Rural roads and as per direction of Engineer-in- charge. 1st Year |
| 45 | 2nd Year |
| 46 | 3rd Year |
| 47 | 4th Year |
| 48 | 5th Year |
| 49 | Maintenance of Bituminous surface road i.e. repair to pot holes and removal of loose materials, trimming of sides, cleaning of surface by providing tack coat, 20 mm thick pre mix carpet and seal coat as per clause 1904.2 of MORD specification for Rural roads and as per direction of Engineer-in- charge. 1st Year |
| 50 | 2nd Year |
| 51 | 3rd Year |
| 52 | 4th Year |
| 53 | 5th Year |
| 54 | Maintenance of Hume Pipe culverts by way of clearing , cleaning erosion repair, repair to crack, parapet wall and protection work as per clause 1908 of MORD specification for Rural roads and as per direction of Engineer- in- charge. 1st Year |
| 55 | 2nd Year |
| 56 | 3rd Year |
| 57 | 4th Year |
| 58 | 5th Year |
| 59 | Maintenance of Road Signs by way of cleaning and repainting of mandatory. Regulatory/ cautionary/ informatory and place identification sign board as per clause 1910 of MORD specification for Rural roads and as per direction of Engineer-in-charge. 1st Year |
| 60 | 2nd Year |
| 61 | 3rd Year |
| 62 | 4th Year |
| 63 | 5th Year |
| 64 | Maintenance of 200 m stones and km stones by way of refixing of tilted stones repairing with cement mortar, cleaning, repairing and lettering on 200mtr. and KM. stone and 5 km stone as per clause 1912 of MORD specification for Rural roads and as per direction of Engineer-in-charge. 1st Year |
| 65 | 2nd Year |
| 66 | 3rd Year |
| 67 | 4th Year |
| 68 | 5th Year |
| 69 | Cutting of branches of trees from Roadway or with a R.O.W. including disposal of wood and leaves to suitable location as per clause 1914 of MORD specification for Rural roads and as per direction of Engineer-in-charge. 1st Year |
| 70 | 2nd Year |
| 71 | 3rd Year |
| 72 | 4th Year |
| 73 | 5th Year |
| 74 | Cutting of shrubs from roadway or with in R.O.W. and disposal of shrubs to suitable location as per clause 1914 of MORD specification for Rural roads and as per direction of Engineer-in- charge. 1st Year |
| 75 | 2nd Year |
| 76 | 3rd Year |
| 77 | 4th Year |
| 78 | 5th Year |
| 79 | Trimming of grass and weeds from shoulder, berms and disposing off the same to suitable location as per clause 1914 of MORD specification for Rural roads and as per direction of Engineer-in-charge. 1st Year |
| 80 | 2nd Year |
| 81 | 3rd Year |
| 82 | 4th Year |
| 83 | 5th Year |
| 84 | Maintenance of drains include erosion, repair, clearing, cleaning, reshaping, regrading deepening of side drains as well as catch water drains as per drawing and technical specification Clause 1907 of MORD specification for Rural roads and as per direction of Engineer-in-charge. 1st Year |
| 85 | 2nd Year |
| 86 | 3rd Year |
| 87 | 4th Year |
| 88 | 5th Year |
| 89 | White washing two coats on parapet walls of CD works and tree trunks including preparation of surface by cleaning scraping etc as per clause 1915 of MORD specification for Rural roads and as per direction of Engineer-in-charge. 1st Year |
| 90 | 2nd Year |
| 91 | 3rd Year |
| 92 | 4th Year |
| 93 | 5th Year Please Enable Macros to View BoQ information |
