|
| 1 | Providing and laying flat brick soling layer on prepared subgrade according to lines, grades and cross-section shown on the drawing, filling joints with Earth, free from clay with a Plasticity Index not exceeding 6, watering and rolling the same with three wheeled road roller 80-100 kN as per MoRD Technical Specification Clause 412. |
| 2 | Brick on edge solingProviding and laying brick on edge soling layer on prepared subgrade according to lines, grades and cross-section shown on the drawing, filling joints with sand, watering and rolling the same with three wheeled road roller 80-100 kN as per MoRD Technical Specification Clause 412. |
| 3 | Providing and applying tack coat with hot straight run Bitumen (VG-30) including heating the bitumen, spraying the bitumen, cleaning and preparing the existing road surface as per specification: on bituminous surface at the rate of 0.50 kg per sqm |
| 4 | Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80 - 100 KN Static rollar capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C or Type D as per Technical MoRD Specification Clause 508.By Manual means: 1) Bitumen (60/70 Grade) VG-30 |
| 5 | Providing and laying seal coat sealing the voids in a bituminious surface laid to the specified levels, grade and cross fall using Type A, or Type B or Type C or type D as per MoRD Techinical Specification Clause 510A. By Manual MeansCase IV Type D (Premix with fine sand)1) Bitumen (60/70 Grade) VG-30 |
| 6 | Repair to pot holes by removal of failed material, trimming the sides to vertical and levelling the bottom, cleaning the same with compressed air or any appropriate method, filled with 75 mm B.M, after applying bitumen emulsion prime coat at the bottom and bitumen emulsion tack coat on sides and on bottom as per MoRD technical specification Clauses 1900, 502, 503 and 504. |
| 7 | Filling in foundation trenches as per drawing & MoRD technical specification Clause 305.3.9, 1200.I) Sand filling |
| 8 | Providing concrete for plain/reinforced concrete in open foundations complete including formwork as per drawings & MoRD technical specifications Clauses 802, 803, 900, 1202 and 1203. (including centering, shuttering, staging etc. but excluding reinforcement).I) P.C.C grade M 10 : ii) Nominal mix 1:3:6 (Hand mixing) |
| 9 | Brick masonry work in cement mortar in foundation completed excluding pointing & plastering as per drawing & MoRD technical specifications Clauses 600, 1202 & 1203..ii) Brick masonry in 1:4 cement mortar |
| 10 | Providing concrete for plain/reinforced concrete in open foundations complete including formwork as per drawings & MoRD technical specifications Clauses 802, 803, 900, 1202 and 1203. (including centering, shuttering, staging etc. but excluding reinforcement).iv) R.C.C grade M 20 |
| 11 | Supplying, fitting & placing Thermo-Mechanically treated bar/ Cold twisted deformed steel bar reinforcement in foundation complete as per drawings & MoRD technical specifications Clauses 1000 & 1202. |
| 12 | Plastering with cement mortar (1:4) 12 mm thick on brickwork/ C.C. work including a finishing coat of neatcement punning with 2.75 kg of cement per sqm in substructure as per MoRD technical specification Clauses613.4 & 1204. |
| 13 | Dismantling of existing structures like culverts, bridges, retaining walls and other structure comprising of masonry,cement concrete, wood work, steel work, including T&P and scaffolding whenever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and upto a lead of 1000 m as per MoRD Technical Specification Clause 202(I) By Manual MeansB) Cement Concrete |
| 14 | Without dewateringEarthwork in excavation for structures as per drawing and MoRD technical specifications Clause 305.1 includingsetting out, construction of shoring & bracing, removal of stumps & other deleterious material and disposal upto alead of 50 m,dressing of sides & bottom and backfilling in trenches with excavated suitable material. Ordinary Soil(i) Upto 3 m depth Please Enable Macros to View BoQ information |
