|
| 1 | Excavation in earth work and disposal of excavated earth upto a lead of 20 metres and lift upto 1.50 metres, disposed earth to be levelled and neatly dressed in Pick-Jumper work. |
| 2 | Providing and laying cement concrete 1:3:6 (1 cement: 3 sand: 6 graded stone aggregate 40mm nominal size) excluding cost of centring & shuttering in. |
| 3 | Providing plinth protection 50mm thick in cement concrete 1:3:6 (1 Cement :3 Sand: 6 graded stone aggregate 20mm nominal size) including all leads and lifts complete in all respect. |
| 4 | Providing form work with steel plates 3.15mm thick welded with angle iron 30x30x5mm so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden batten and ballies, height of propping and centering below supporting floor to ceiling not exceeding 4 metres and removal of the same for insitu reinforced concrete & plain conrete work in. |
| 5 | Vertical surfaces such as walls (any thickness) partition and the like including attached pillasters, buttresses, plinth and string courses and the like. |
| 6 | 6 mm thick cement celling plaster in single coat of fair sides of for interior plastering upto floor two level including arrises internal rounded angles chamber and rounded angles not exceeding 80mm in girth and finished even and smooth in cement mortar4 1:3(1cement : 3sand) includung all leads and lifts complete in all respects. |
| 7 | Steel work welded in builtup section including cutting hoisting, fixing in position and applying a priming coat of red lead paint. |
| 8 | Providing and laying cement concrete 1:5:10 (1 cement: 5 sand: 10 graded stone aggregate 40mm nominal size) and curing complete excluding cost of form work in retaining walls/ breast walls, per HPPWD specifications. |
| 9 | 20mm cement plaster in single coat on the rough side of brick/stone masonry for interior plastering upto floor two level including arrises,internal rounded angles,chamfers and or rounded angles not exceeding 80mm in girth and finished even and smooth lincluding all leads and lifts complete in all respect |
| 10 | Providing and laying cement concrete work for flooring 1:2:4(1 Cement :2 Sand: 4 graded stone aggregate 20mm nominal size)and curing complete excluding cost of form work and reinforcement for reinforced concrete work in:- |
| 11 | Providing stone kharonja drain 45cm vide in 1:6 around the Side of PumpHouse 28Mtrs. Including carriage of material. |
| 12 | Distempering(two coats) with oil bond washable distemper of approved brand and manufacture and of required shade or undecorated wall surface to given an even shade over and including a priming coat with distemper primer of approved brand and manufacture after thoroughly brushing the surface free from mortar droppings and other foreign matter and also including preparing the surface even and sand papered smooth priming coat with distemper primer including all leads and lifts complete in all respect. |
| 13 | Applying priming coat over new steel & other metal surface after and including preparing the surface by throughly cleaning oil grease dirt and other foreign metter and scoured with wire brushes fine steel wool scrapper and send paper complee in all respects. |
| 14 | Painting two coats (excluding priming coat) on new steel & other metal surface with enamel paint brushing to give an even shade including cleaning of all dirt, dust and other foreign matter with in all leads and lifts complete in all respect. |
| 15 | Providing and installing submersible pump of Crompton / KSB make confirming to ISI- 9034-1976 along with a directly coupled submersible type squirrel case electric submersible motor suitable for operation on 230 V, single phase 50 CPS, AC supply with water lubricated bearing, provided with pivoted segment type thrust bearings to with stand vertical pressure with minimum wear and terar and with device to take up the expansion of water with heating of motor complete in all respects.( 1 Set of 2HP) for booster stage Total Head :- 70 Mtr DIischarge : 1.05 LPS R / Main 32mm dia (L) 70 Rmt |
| 16 | Providing & fixing cubical type flor mounted MS sheet Angle channel made Almirah MUG -30 FASTLY with wide band coil) L&T make HSN code -8536 type pannel dully powder coated suitable for 30HP induction motor , comprising of following items |
| 17 | Supplying and fixing submersible cable 4mm2 3 core submersible cable of L&T /Havell make complete in all respects. |
| 18 | Supplying and fixing single phase panal board of BS / L & T / Havells / BS make with Ampears meter, volt meter Over load relay kit kat indicator set MCCB etc. including carriage of material up to all leads and lifts complete in all respects. |
| 19 | Providing and fixing of GSM based remote submersible pump auto operation control cum protection device for motor single / Three phase complete in all respects with in all leads and lifts as per direction of Engineer-in-Charge including testing, commissioning complete with following features:- i) Remote start / stop operation of pump with Call /SMS. ii) Pump start / stop feedback through call /SMS with reason of stop / trip. iii) Pump start / stop feedback for unauthorized local start / stop through starter. iv) Auto / Manual mode for auto pump start post grid supply resumption. v) Remotely settable timer for scheduling pump start / stop on Hourly / daily / Weekly / Monthly basis. vi) Remotely settable timer for scheduling pump starter / stop for fixed hours in a day. vii) Inbuilt Protection against over load, / under voltage/ Dry run/ phase reversal/ Single phasing . With user configurable remotely settable voltage and current limits for these protections. viii) Inbuilt GPS tracker for prevention of loss / theft. ix) Controlled operation access through authenticated mobile numbers only which can be added for removed by main user remotely. |
| 20 | Providing and fixing Gun metal wheel valves ordinary split, tapper edge, non-rising spindle gate valves of class-1 for cold service (temp not exceeding 45 gegree Centrigrade) screwed type as per IS : 778-1984 .all leads and lifts complete in all respects. |
| 21 | 15mm dia |
| 22 | 20mm dia |
| 23 | 25mm dia |
| 24 | 32mm dia |
| 25 | 40mm dia |
| 26 | 50mm dia |
| 27 | 65mm dia |
| 28 | Providing and Fixing G.I union of various Dia in all leads and lift.complete in all respects. |
| 29 | 15mm dia |
| 30 | 20mm dia |
| 31 | 25mm dia |
| 32 | 32mm dia |
| 33 | 40mm dia |
| 34 | 50mm dia |
| 35 | Providing and Fixing G.I sockets of various Dia in all leads and lift.complete in all respects. |
| 36 | 15mm dia |
| 37 | 20mm dia |
| 38 | 25mm dia |
| 39 | 32mm dia |
| 40 | 40mm dia |
| 41 | 50mm dia |
| 42 | Providing and Fixing G.I. Nipple of various length & various Dia in all leads and lift.complete in all respects. |
| 43 | 15mm dia |
| 44 | 20mm dia |
| 45 | 25mm dia |
| 46 | 32mm dia |
| 47 | 40mm dia |
| 48 | 50mm dia |
| 49 | Providing and Fixing G.I. Tee of various Dia in all leads and lift.complete in all respects. |
| 50 | 20 x20 x15 mm |
| 51 | 25 x25 x15 mm |
| 52 | 25 x25 x25 mm |
| 53 | 25 x25 x20 mm |
| 54 | 32 x32 x25 mm |
| 55 | 32 x32 x20 mm |
| 56 | 40 x40 x32 mm |
| 57 | 40 x40 x25 mm |
| 58 | 40 x40 x40 mm |
| 59 | Providing and Fixing G.I.reducer of various Dia in all leads and lift.complete in all respects. |
| 60 | 20 x 15mm dia |
| 61 | 25 x 15mm dia |
| 62 | 25 x 20mm dia |
| 63 | 32 x 25mm dia |
| 64 | 32 x 20mm dia |
| 65 | 40 x 32 mm dia |
| 66 | 40 x 25 mm dia |
| 67 | Providing and Fixing C.I. Sluice valve of 50mm Dia in all leads and lift.complete in all respects. |
| 68 | Providing and Fixing C.I. Sluice valve of 80mm Dia in all leads and lift.complete in all respects. Please Enable Macros to View BoQ information |
