|
| 1 | CIVIL WORKS- Demolishing,Centering & Shuttering,Concreting Work for fixing SS C GROOVE, SEAL TRACK and SILL BEAM. |
| 2 | 15.9.1:Demolishing stone rubble masonry manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer -in- Charges:In Lime Mortar |
| 3 | 15.2.1:Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 4 | 5.9.6:Centering and shuttering including strutting, etc. and removal of form for:Columns, Pillars, Piers, Abutments, Posts and Struts |
| 5 | 4.1.2:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:1½:3 (1 Cement: 1½ coarse sand (zone-III) derived from natural sources : 3graded stone aggregate 20 mm nominal size derived from natural sources) |
| 6 | 4.1.5:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 7 | 5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more |
| 8 | 5.2.2:Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up tot floor five level excluding cost of centering, shuttering, finishing and reinforcement :1:1.5:3( 1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 9 | 13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) |
| 10 | SUPPLY, FABRICATION & ERECTION OF MS SHUTTERS-6 NOS |
| 11 | OD20348/2024-2025:Dismantling of the canal shutter (Up to 2 Tonne weight) / Hoisting unit/Embedded parts etc. of the same and stacking at a distance of 100 meter including hire of machinery, labour etc. complete as directed by the departmental officer at the site. (Weight of the unserviceable shutters and embedded parts may be calculated as 60% and unserviceable hoisting units as 80%) |
| 12 | OD20343/2024-2025:Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges., |
| 13 | OD20344/2024-2025:Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges., |
| 14 | 85.103:Supply of MS checquered plates including cost of conveyance charges |
| 15 | OD20345/2024-2025:Supply of MS round bar including cost of conveyance charges., |
| 16 | OD53467/2025-2026:Fabrication,Supply,Erection and Assembling in correct position and alignment by welding SS EMBEDDED PARTS in 304L Grade like roller track,seal track,Seal seat etc as per approved specifications,drawings and directions of deptl officer at site including cost of all materials,labour,machinery for planing,welding,shearing,grinding etc,lead and lift,conveyance,incidental and handling etc complete. |
| 17 | OD20347/2024-2025:Fabrication and errection of Embedded parts for canal shutters ( lJp to 2 tonne weight ) and accessories as per approved specifications, drawings and directions of deptl fficer at site including cost of labour,machinery, all leads and lifts, incidental and handling charges etc complete but excluding cost of material already supplied., |
| 18 | OD53468/2025-2026:HOT DIP GALVANISING the fabricated workpiece to get a minimum coating thickness of 80microns. (The workpiece is to be caustic cleaned for removing impurities like grease, dirt etc.then it is pickled to remove oxides and is then given flux coating to prevent further oxidation and is then finally dipped in zinc bath) |
| 19 | OD20349/2024-2025:Fabrication and supply of Structural steel canal shutters ( Up to 2 tonne weight ) /Hoisting Bridge /Platform and accessories etc. for the same as per approved specifications, drawings and directions of deptl fficer at site including cost of labour, machinery, all leads and lifts, incidental and handling charges etc complete but excluding cost of material already supplied., |
| 20 | 85.114:Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc on dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350 microns after cleaning the surface using hand and power tool cleaning including cost of all materials, labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site |
| 21 | 85.115:Cost of painting with 2 coats of enamel paint over 1 coat of zinchromate primer as per IS1477:1994 after hand and power tool cleaning including cost of all materials, labour charges, cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site |
| 22 | OD20351/2024-2025:Providing EN-8 Screw Rod 7.50 Tonne Capacity 4.00 Mtr lift Screw Rod having one number of EN-8 Screw Shaft having a lifting speed of around 5.00 cm/min for 24 rpm of hand operation including cost of all material, labour, hire charges and conveyance. (63mm Dia Screw rod )., |
| 23 | OD53466/2025-2026:Re-Conditioning of existing EN-8 Screw rod including cost of all materials, labour charges, hire charges, energy charges, conveyance, all leads and lifts etc. complete., |
| 24 | OD53469/2025-2026:PROVIDING of WORM and PINION having a lifting speed of around 5.00 cm/min for hand operation. having gearbox wall thickness of 12mm for side, 16mm for top and 24mm base. Top plate fixed with minimum 8 nos of M12 bolt , including cost of Mechanical stoper, Locking arrangement, Operating handle and all other materials, labour, hire charges and conveyance. |
| 25 | OD20356/2024-2025:SUPPLYING and APPLYING GREASE on NEW SCREW ROD for CANAL GATE., |
| 26 | OD20350/2024-2025:Erection of the Canal Shutter ( Up to 2 Tonne weight ) / Hoisting Bridge / Platform including hand rails , ladder etc. for the same including . alignment correcting and setting complete including cost of all labour, machinery, incidental and conveyance , lead and lift charges etc complete but excluding cost of materials already supplied., |
| 27 | OD53470/2025-2026:SUPPLYING and STACKING of PAD LOCK. Please Enable Macros to View BoQ information |
