|
| 1 | Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres:80% All kinds of Soil, 10% Soft Rock, 10% Hard Rock.(Complete Job) |
| 2 | Earth work in excavation by mechanical means in trenches for foundations, drains, pipes, cables etc. (Not exceeding 1.5 mtr in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, depth upto 1.5mtr. including disposal of excavated earth upto 1 mtr from cutting edge, disposed earth is to be levelled and neatly dressed in all kinds of soil. |
| 3 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering- All work upto plinth level. 1:5:10 (1 cement: 5 coarse sand: 10 graded stone aggregate 40mm nominal size) Crushed . |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering.All works upto plinth level in 1:3:6 (1 cement: 3 coarse sand: 6 graded stone aggregate 20mm nominal size) crushed. |
| 5 | Brick work with common burnt clay F.P.S.(non-modualar) bricks of class designation 75 in foundation and plinth in Cement mortar 1 :6 ( 1 cement : 6 coarse sand) & Extra for brick work in superstructure above plinth level upto floor V level. (By manual means) |
| 6 | Providing and laying Reinforced Cement Concrete 1:1.5:3 (1 cement: 1.5 coarse sand: 3 graded stone aggregate 20 mm nominal size) in suspended floors, balconies, landings and staircase having upto 15° slope. excluding cost of centering and shuttering , all work upto floor V level |
| 7 | Reinforcement for RCC work including straightening cutting, bending, placing in position & binding all complete with TMT bars. |
| 8 | Centring and Shuttering including strutting, propping etc and removal of form work for |
| 9 | Foundations: footings, bases of columns etc. for mass concrete. |
| 10 | Suspended floors, roofs, landings, balconies and access platform. |
| 11 | Edges of Slabs and Break in floors and walls (Under 20 cms wide) |
| 12 | 6 mm Cement plaster to ceiling of mix 1 : 3 ( 1 cement : 3 fine sand) |
| 13 | 12mm cement plaster of mix 1:6 (1 cement : 6 fine sand) |
| 14 | 15mm Cement plaster on the rough side of single or half brick wall of mix 1 : 6 ( 1 cement : 6 fine sand) |
| 15 | Steel work welded in built up sections/framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. 10.25.1 In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete. |
| 16 | Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturers) of 1st quality conforming to IS: 15622 of approved make, laid on 20 mm thick bed of cement mortar 1: 4 ( 1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc., complete. 11.50.1 In colour such as White, Ivory, Grey, Fume Red Brown |
| 17 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer- in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 18 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work |
| 19 | White washing with lime to give an even shade on New Work (three or more coats) |
| 20 | Providing and fixing PVC pipes with necessary stays / clamps with fasteners of following dia working pressure 4kg/cm2 of make Supreme, finolex or equivalent(LMR) |
| 21 | 110 mm dia |
| 22 | 75 mm dia |
| 23 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including all CPVC plain and brass threaded fittings. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer-in-charge. |
| 24 | 20mm nominal outer dia pipes. |
| 25 | 25mm nominal outer dia pipes. |
| 26 | Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast Iron P or S trap, 10 liter low level white P.V.C. flushing cistern, including flush pipe (of approved make) with manually controlled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. White vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests. |
| 27 | Providing and fixing wash basin with C.I. brackets, 15mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required : White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps. |
| 28 | Providing and fixing on wall face un-plasticized - PVC moulded fittings/accessories for un plasticized Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. |
| 29 | Single tee without door 75x75x75 mm |
| 30 | Single tee without door 110x110x110 mm |
| 31 | Bend 87.5° 75 mm bend |
| 32 | Bend 87.5°110 mm bend |
| 33 | Providing and fixing white vitreous china pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. |
| 34 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS standards and weighing not less than 810 gms 15 mm nominal bore of make hindware/cera/jaquar or as approved by site incharge |
| 35 | Providing & fixing flow trap including all fittings complete job |
| 36 | Providing and fixing C.P. brass angle valve for basin mixer and gyser points _of approved make conforming to IS : 8931 15 mm nominal bore of make hindware/cera/jaquar or as approved by site incharge |
| 37 | Providing and fixing uplasticized PVC connection pipe with brass unions 30 cm length 15 mm nominal bore |
| 38 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C waste fittings complete: Flexible pipe 32mm dia |
| 39 | Providing & fixing CP grading of 100mm dia of approved brand |
| 40 | Providing & fixing PTMT soap dish holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements weighing not less than 106gms. |
| 41 | Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete 20mm nominal bore |
| 42 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank |
| 43 | Carriage of material from source to site of work by mechanical transport including loading /unloading and stacking complete. |
| 44 | Sand for a distance of 100 kms by MT & 1Km by HL |
| 45 | Stone aggregate below 40mm for a distance of 50 kms by MT & 1Km by HL |
| 46 | Bricks for a distance of 80 kms by MT & 1Km by HL Please Enable Macros to View BoQ information |
