|
| 1 | Finishing walls with Putty appro roved brand and manufacture and of required shunde on undacorated wall wurface to give even thoude over including curing and cost of all material, labour, T&P etc required for proper completion of work |
| 2 | Finishing walls with exterior emulsion paint (Apex) of approved brand and manufacture and of required shade on undacorated wall surface to give even shade over 1.25 Ltr/10sgm including one cont of primer applid 0.75Ltr/10sqm.coat curing and cost of all material, labour. T&P etc. required for proper completion of work for two coat. |
| 3 | Construction of gramular hase (GSB) by providing course graded material, spreading in uniform layer with mortor grader on prepared surface, mixing by mixin place method with rotovator OMC and compacting with viberatory roller to achieve the desired density as per clause 401. |
| 4 | Providing & laying of Rubber moudded Interlocking Concrete block pavement with 80mm thick CBP (75% Gray & 25% Red/Yellow colored) having strength not less than 30KN/SOM complete as per technical specification Clause 1500 |
| 5 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering-All work up to plinth level 1:6:12 (1 cement: 6 coarse sand (zone-iii): 12 graded Brick aggregate 40mm (nominal size) |
| 6 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorbtion less than 0.08% and conforming to IS 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand), jointing with grey slurry @ 3.3 kg/sqm including grouting the joints with white cement and matching pigements etc. complete. Size of tile 600x600mm |
| 7 | Tile work in skirting, risers of steps and dado up to 2 m height over 12 mm thick bed of cement mortar 1:3 (1 cement :3 coarse sand) and jointed with grey cement slurry @ 3.3 kg/sqm, including pointing in white cement mixed with pigment of matching shade complete Marble tiles (polished) Raj Nagar 8 mm thick |
| 8 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, Including all CPVC plain & brass threaded fittings, Ve fixing the pipe with clamps at 1.00 mm spacing. This includes Jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting 25 mm nominal outer dia Pipes |
| 9 | Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 grams/sqm, both side inclusive) consisting of main \\"T\\" runner sheet, spaced at 1200 mm center to center and cross \\"T\\" sheet, 1200 mm long spaced between main \\"T\\" at 600 secondary cross \\"T\\" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main \\"T runners to be suspended from celling using Gl slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm Gl adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T bottom exposed width of 24 mm of all T- sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. Gi Metal Celling Lay in plain Tegular edge Global white color tiles of size 595-595 mm, and 0.5 mm thick with 8 mm drop: made of Gl sheet having galvanizing of 100 gms/sqm (both sides |
| 10 | Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle Iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer.Using M.S. angels 40x40x6 mm for diagonal braces |
| 11 | Supply and fixing of anodized aluminium partition having 2mm thick aluminium. Section, partly glazed and partly 12mm thick laminated board. Aluminium board size 83.50x44.65mm vertical member and 11.40x44.45 as bottom and horizontal member with all fitting, glass panes of 4mm thick handle and locks complete. |
| 12 | Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing T-iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete as per the direction of Engineer-In-charge |
| 13 | Steel work welded in built up sections/framed work, including cutting hoisting, fixing in position and applying a priming cout of approved steel primer using structural steel etc. as required In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 14 | Applying priming coat over new steel and other metal surface upto 10cm. In width or girth or small not exceeding 0.10 Sq.M. area after and Including preparing the surface by thoroughly clearing oil, grease, dirt and other foreign matter and scoured with wire brushed, fine steel wood. Scrapper, sand papering and knotting including cost of all materials, labour T&P etc. required for proper completion of workPainting 1st coat over priming coat (but excluding cost of priming coat) on steel and other metal surfaces upto 10cm width or girth or omall articles not exceeding 0.10 Sq. M. in area with superior synthetic enamel such as Lavol 3. Hi gloss Apcolite, Superlac, Dubus specified brushing to give and even shade and including the cleaning the surface of all dirt, dust and other foreign matter sand papering and scrapping including cost of all materials, labour, tools and plants etc. required for proper completion of work Extra over item 2 and 2(a) above but for every coat of paint after first coat. |
| 15 | Supply and fixing of LED Tube Light batten fitting suitable for up to 1 X 22 watt LED tube light on surface complete in all respect |
| 16 | Supply and fitting of ceiling fan Usha, Khetan, Bajaj L.S.I mark including all complete. |
| 17 | Supply and fixing of switch box 250 x 250 x 65 mm size of each approved make made up of 1.0 mm thick ISI Marked G.P.sheet All 4 corners folded & spot welded for screw and holes plugged with PVC Nylon Caps. Two or more holes for pipe entry of 25.4 mm on upper and lower sides of the box. Holes shuld be semi-shuttered type and fitted with heavy brass Earth Piller duly screwed & brand name should be embossed. Box flushed in wall including cutting of brick work, fixing it to the level with cement sand mortar, including matching colour wash with s/o all materials, labour and T&P required for proper completion of work as directed at site by the Engineer in charge |
| 18 | Supply and fixing of 60Amp to 32Amp DPMCB |
| 19 | Supply of curtains for door & windows etc all complete. |
| 20 | Supply of R.O. (water purifier) etc all complete |
| 21 | Supply and Installation of 01 No. Split A.C. 1.5 Ton etc. all complete |
| 22 | Supply of Revolving Chair etc all complete |
| 23 | Supply of Computer table etc all complete |
| 24 | Supply of Visitor Chair etc all complete. |
| 25 | Supply of Office almirah small size etc all complete. |
| 26 | Add 18 % G.S.T. Please Enable Macros to View BoQ information |
