|
| 1 | Supplying chemical emulsion in sealed containers including delivery as specified. |
| 2 | Chlorpyriphos/ Lindane emulsifiable concentrate of 20% |
| 3 | Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti- termite treatment (excluding the cost of chemical emulsion) : |
| 4 | Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: |
| 5 | With Chlorpyriphos/Lindane E.C. 20% with 1% concentration |
| 6 | Treatment of existing masonry using chemical emulsion @ one litre per hole at 300 mm interval including drilling holes at 45 degree and plugging them with cement mortar 1:2 (1 cement : 2 coarse sand) to the full depth of the hole : |
| 7 | With Chlorpyriphos/Lindane E.C. 20% with 1% concentration |
| 8 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : |
| 9 | 12.5 mm thick tapered edge gypsum moisture resistant board |
| 10 | Providing and fixing Gl Clip in Metal Ceiling System of 600x600 mm module which includes providing and fixing 'C' wall angle of size 20x30x20 mm made of 0.5 mm thick pre painted steel along the perimeter of the room with help of nylon sleeves and wooden screws at 300 mm center to centre, suspending the main C carrier of size 10x38x10 mm made of G.I steel 0.7 mm thick from the soffit with help of soffit cleat 37x27x25x1.6 mm, rawl plugs of size 38x12 mm and C carrier suspension clip and main carrier bracket at 1000 mm c/c. Inverted triangle shaped Spring Tee having height of 24 mm and width of 34 mm made of Gl steel 0.45 mm thick is then fixed to the main C carrier and in direction perpendicular to it at 600 mm centers with help of suspension brackets. Wherever the main C carrier and spring T have to join, C carrier and spring T connectors have to be used. All sections to be galvanized @ 120 gms/sqm (both side inclusive), fixing with clip in tiles into spring T with : |
| 11 | GI Metal Ceiling Clip in plain Beveled edge global white color tiles of size 600x600 and 0.5 mm thick with 25 mm height, made of G I sheet having galvanizing of 100 gms/ sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending. |
| 12 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour : |
| 13 | New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre |
| 14 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : |
| 15 | One or more coats on old work |
| 16 | Providing and fixing Zebra blinds (Dual layer blinds) in Doors, windows etc. made of Dim-out blinds in fabric 100% polyester range ensure adequate darkening & privacy in semi opaque fabric sahara / Solus in fabric black out shade ; thickness of Solid fabric part 0.46mm (± 5%) Mesh thickness : 0.09 mm; and repeat size of fabric 10.cm ( ± 5%) & Mesh part size 7 cm ( ( ± 5%) fixtures & valance in powder coated in white Color and patterns as per manufacturers specification & color fastness of light- ( 4-5) grade etc complete of make Vista {Sahara sheer (SDSR-07 Brown)},Aero-lux,Hunter Douglas ,AIPS ,Callistus of required clour & shade as per direction of Engineer-in-Charge.[The agency should provide certificate from the company to prove originality and warranty of the blinds after completion of work] |
| 17 | Providing and pasting Customised Wallpaper (joint less) UV printed Non-woven on finished wall surface as per manufacturers specification etc complete of required clour & shade as per direction of Engineer-in-Charge. |
| 18 | Providing and mixing of Self leveling with the use of MYK FloAnn Soloplan -SOM, commercial self smoothing and leveling compound consisting of high quality special cement and selected fillers,with water at rate of 5.5-6.00 Ltr for 25Kg bag of MYK FloAnn Soloplan -SOM, installing at thickness of 3mm using suitable pinrake trowel and notch trowel,finally rolling the surface with spike roller,etc and complete as per manufacturer's specification. [ Mixed density of powder :2gm/cc;Weight of fresh mortar :2.0 Kg / Ltr; Pot Life at 23°C :20 min Approx; Flow life time :15min;Initial setting time :40 min; Final setting time :1Hr;Bal impact hardness :6.5mm;Scratch hardness 1.6mm; Compressive Strength :after 28days approx 4.5N/mm2;Flexural strength at 27°C (ASTM C348) after 24 hrs :1.5N/ mm,after 7 days approx 3N/ mm2;Product confirms to standard; EN13813CT -C15-F-4.5 including Dismentling pvc flooring including cutting the welded joints and cleaning the glue from the floorand as per direction of Engineer-in-charge complete. |
| 19 | Providing and fixing 2 mm thick recycled PVC slip resistance vinyl sheet flooring with PUR of approved colour & shade of Armstrong range ACCOLADE SAFE PLUS/ polyflor/Forbo for range Prestige or equivalent make having wear resistance of Group 'T' as per EN 660-2 and should have a residual indentation of ≤ 0.10 mm confirming to EN433. The vinyl sheet shall be laid & fixed with any water based adhesive preferrably AROBOND-44 of M/s, colour bond make or VC 31 of M/s Pidilite ind. or any other make as per manufacturer's specification and base should be prepare with self levelling compound of Cement Aggregate additives of thickness 2-3 mm as required and as per direction of Engineer-in-charge complete. |
| 20 | Modified Estimated Cost after using Correction factor on DSR-2023 on account of GST @ 0.973 |
| 21 | Add Cost Index @ 3% on DSR 2023 item. Please Enable Macros to View BoQ information |
