|
| 1 | Working Charges-Pipe Replacing work |
| 2 | 15.47.1:Dismantling asbestos cement pressure pipes including excavation and refilling trenches after taking out the pipes manually / by mechanical means and stacking the pipes within 50 metres lead as per direction of Engineer-in-Charge:Upto 150 mm diameter |
| 3 | 15.47.2:Dismantling asbestos cement pressure pipes including excavation and refilling trenches after taking out the pipes manually / by mechanical means and stacking the pipes within 50 metres lead as per direction of Engineer-in-Charge:Above 150 mm diameter |
| 4 | 15.9.2:Demolishing stone rubble masonry manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer -in- Charges:In cement mortar |
| 5 | 100.1.1:Excavating trenches of required width for pipes, cables, etc., including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20cm in depth, including consolidating each deposited layer by ramming, watering, etc., and disposing of surplus excavated soil as directed, within a lead of 50m, in all kinds of soil. |
| 6 | 100.8.1:Fencing one side of trenches, 1.50m height with two rows of 10cm plastic caution tape in vertical casuarina pole (girth 15cm to 24cm) fixed at 2m intervals. |
| 7 | 100.25.1:Cutting of 80mm AC pipes of all classes diametrically, the cut being diametrically perpendicular to the axis of pipe and smoothening of the cut ends etc., complete. |
| 8 | 100.25.4:Cutting of 150mm AC pipes of all classes diametrically, the cut being diametrically perpendicular to the axis of pipe and smoothening of the cut ends etc., complete. |
| 9 | 100.25.6:Cutting of 250mm AC pipes of all classes diametrically, the cut being diametrically perpendicular to the axis of pipe and smoothening of the cut ends etc., complete. |
| 10 | 100.25.7:Cutting of 300mm AC pipes of all classes diametrically, the cut being diametrically perpendicular to the axis of pipe and smoothening of the cut ends etc., complete. |
| 11 | 100.59.1:Cutting the bituminous / concrete roads with cutting machine for a minimum depth of 200mm along the sides of proposed alignment of the pipe to be laid without causing any damage to other utilities, including the charges for hire and conveyance of tools and plant, cost of consumables and charges for lighting, watching, ribbon fencing, caution boards, traffic diversion, and as per the direction of departmental officers etc. complete, before carrying out the demolition of bituminous / concrete road by mechanical means and carrying out the excavation. |
| 12 | 18.12.8:Providing and fixing G.I. pipes complete with G.I fittings including trenching and refilling etc. External work80 mm dia nominal bore |
| 13 | 100.37.6.1:In situ fabrication of M.S. pipes of size 150mm (I.D.) using 8mm thick M.S. plate including cost and conveyance charges of M.S. plate, all fabrication charges, charges of painting the steel work with two or more coat deluxe multi surface paint to give an even shade over an under-coat of primer etc., complete. |
| 14 | 100.37.6.2:Fabricating M.S. flanges of diameter 150mm using 12mm thick M.S. plate including cost and conveyance charges of M.S. plate, all fabrication charges, charges of painting the steel work with two or more coat deluxe multi surface paint to give an even shade over an under-coat of primer etc., complete: For pipes fabricated with 8mm thick M.S. plates. |
| 15 | 100.37.6.3:Cutting 150mm (I.D.) M.S. pipes for making bends and other specials by gas cutting including cost of gas, all labour and hire charges of tools etc., complete: For pipes fabricated with 8mm thick M.S. plates. |
| 16 | 100.37.6.4:Welding 150mm (I.D.) M.S. pipes for making bends and other specials by gas/electric welding machine including cost of gas and welding rods, all labour and hire charges of tools etc., complete: For pipes fabricated with 8mm thick M.S. plates. |
| 17 | 100.37.6.5:Grinding cut and weld edges of 150mm (I.D.) M.S. pipes during fabrication work including all labour and hire charges of tools etc., complete: For pipes fabricated with 8mm thick M.S. plates. |
| 18 | 100.37.8.1:In situ fabrication of M.S. pipes of size 250mm (I.D.) using 8mm thick M.S. plate including cost and conveyance charges of M.S. plate, all fabrication charges, charges of painting the steel work with two or more coat deluxe multi surface paint to give an even shade over an under-coat of primer etc., complete. |
| 19 | 100.37.8.2:Fabricating M.S. flanges of diameter 250mm using 12mm thick M.S. plate including cost and conveyance charges of M.S. plate, all fabrication charges, charges of painting the steel work with two or more coat deluxe multi surface paint to give an even shade over an under-coat of primer etc., complete: For pipes fabricated with 8mm thick M.S. plates. |
| 20 | 100.37.8.3:Cutting 250mm (I.D.) M.S. pipes for making bends and other specials by gas cutting including cost of gas, all labour and hire charges of tools etc., complete: For pipes fabricated with 8mm thick M.S. plates. |
| 21 | 100.37.8.4:Welding 250mm (I.D.) M.S. pipes for making bends and other specials by gas/electric welding machine including cost of gas and welding rods, all labour and hire charges of tools etc., complete: For pipes fabricated with 8mm thick M.S. plates. |
| 22 | 100.37.8.5:Grinding cut and weld edges of 250mm (I.D.) M.S. pipes during fabrication work including all labour and hire charges of tools etc., complete: For pipes fabricated with 8mm thick M.S. plates. |
| 23 | 100.37.9.1:In situ fabrication of M.S. pipes of size 300mm (I.D.) using 8mm thick M.S. plate including cost and conveyance charges of M.S. plate, all fabrication charges, charges of painting the steel work with two or more coat deluxe multi surface paint to give an even shade over an under-coat of primer etc., complete. |
| 24 | 100.37.9.2:Fabricating M.S. flanges of diameter 300mm using 12mm thick M.S. plate including cost and conveyance charges of M.S. plate, all fabrication charges, charges of painting the steel work with two or more coat deluxe multi surface paint to give an even shade over an under-coat of primer etc., complete: For pipes fabricated with 8mm thick M.S. plates. |
| 25 | 100.37.9.3:Cutting 300mm (I.D.) M.S. pipes for making bends and other specials by gas cutting including cost of gas, all labour and hire charges of tools etc., complete: For pipes fabricated with 8mm thick M.S. plates. |
| 26 | 100.37.9.4:Welding 300mm (I.D.) M.S. pipes for making bends and other specials by gas/electric welding machine including cost of gas and welding rods, all labour and hire charges of tools etc., complete: For pipes fabricated with 8mm thick M.S. plates. |
| 27 | 100.37.9.5:Grinding cut and weld edges of 300mm (I.D.) M.S. pipes during fabrication work including all labour and hire charges of tools etc., complete: For pipes fabricated with 8mm thick M.S. plates. |
| 28 | OD188804/2025-2026:Charges for jointing 300 mm Pipes with the suitable mechanical joint or any other type joint without causing any damages to the remaining portion of the line and specials after cleaning the ends, centering the pipe, testing the line to the required test pressure, including the charges of hire and conveyance of tools, plants and materials to the site, bailing out water, lighting, watching, ribbon fencing, caution boards, traffic diversion but excluding cost of mechanical joint and as per the direction of departmental officers etc. complete |
| 29 | OD188802/2025-2026:Charges for jointing 250 mm Pipes with the suitable mechanical joint or any other type joint without causing any damages to the remaining portion of the line and specials after cleaning the ends, centering the pipe, testing the line to the required test pressure, including the charges of hire and conveyance of tools, plants and materials to the site, bailing out water, lighting, watching, ribbon fencing, caution boards, traffic diversion but excluding cost of mechanical joint and as per the direction of departmental officers etc. complete |
| 30 | OD188805/2025-2026:Fabricating and supplying at site 300 mm x 90 Degree or nearest angle MS D/F Bend of length 1.0 m according to site conditions, using 10 mm thick MS plate for body and 16 mm thick plates for flanges including cost and conveyance charges of MS plate,all fabrication charges including drilling suitable size holes,<br>charges of painting the steel work with two or more coat deluxe multi surface paint to give an even shade over an under coat of primer etc complete : (Nut & Bolts, washers, IR packing etc. for jointing may be paid seperately) |
| 31 | OD188798/2025-2026:Fabricating and supplying at site 250 mm x 90 Degree or nearest angle MS D/F Bend of length 1.0 m according to site conditions, using 10 mm thick MS plate for body and 16 mm thick plates for flanges including cost and conveyance charges of MS plate,all fabrication charges including drilling suitable size holes,charges of painting the steel work with two or more coat deluxe multi surface paint to give an even shade over an under coat of primer etc complete : (Nut & Bolts, washers, IR packing etc. for jointing may be paid seperately) |
| 32 | OD188803/2025-2026:Fabricating and supplying at site MS mechanical joint with Flanged Tail piece suitable for jointing 300 mm DI K9 pipe made by 8 mm thick MS plate for body, 12 mm MS Plate for Flanges, 16x16 mm square bar bent and welded inside at both ends for seating arrangements of rubber gaskets, providing 8 number cleats at one end made from 10 mm thick MS sheet with cleat supports including all cost of materials, accessories like 20 mm rubber gasket and nut and bolts (24 x 85 mm) conveyance charges and fabrication charges such as cutting, welding |
| 33 | OD188799/2025-2026:Fabricating and supplying at site MS mechanical joint with Flanged Tail piece suitable for jointing 250 mm DI K9 pipe made by 8 mm thick MS plate for body, 12 mm MS Plate for Flanges, 16x16 mm square bar bent and welded inside at both ends for seating arrangements of rubber gaskets, providing 8 number cleats at one end made from 10 mm thick MS sheet with cleat supports including all cost of materials, accessories like 20 mm rubber gasket and nut and bolts (24 x 85 mm) conveyance charges and fabrication charges such as cutting, welding |
| 34 | OD188806/2025-2026:Taking connection from the existing line by using Pvc/ Ms/CI saddle or Tee including alllabour charges, earth work excavation, refilling, bailing out water, hire for tools etc. complete butexcluding cost of materials.& lt;br>110 mm to 160 mm dia PVC pipe. |
| 35 | OD188801/2025-2026:Taking connection from the existing line by using Pvc/ Ms/CI saddle or Tee including alllabour charges, earth work excavation, refilling, bailing out water, hire for tools etc. complete butexcluding cost of materials. above 160 mm dia pipe. |
| 36 | 18.68.1:Providing and laying D.I specials of class K - 12 suitable for push - on jointing as per IS : 9523 :Upt 600 mm dia |
| 37 | 100.31.1.4:Conveying and fixing C.I. sluice valves (with cap) by providing bolts, nuts, rubber insertions etc., complete, but excluding the cost of the valve (tail pieces, if required, will be paid separately): 150mm diameter, Class I. |
| 38 | 100.31.1.7:Conveying and fixing C.I. sluice valves (with cap) by providing bolts, nuts, rubber insertions etc., complete, but excluding the cost of the valve (tail pieces, if required, will be paid separately): 300mm diameter, Class I. |
| 39 | 18.59.1:Providing and fixing C.I double acting air valve of approved quality with bolts, nuts, rubber insertion etc. complete ( The tail pieces, tapers etc. if required will be paid separately):50 mm dia |
| 40 | 18.59.2:Providing and fixing C.I double acting air valve of approved quality with bolts, nuts, rubber insertion etc. complete ( The tail pieces, tapers etc. if required will be paid separately):80 mm dia |
| 41 | 18.17.4:Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :50 mm nominal bore |
| 42 | OD188800/2025-2026:Supplying and fitting M.S saddle piece having not less than 100 mm width in the existing 250/300 mm MS pipe line, welding 50 mm GI coupling on the saddle piece, boring the main including all the cost of specials for fitting air valve etc complete as per the direction of departmental officers. |
| 43 | 100.59.2:Refilling the trenches with a wet mix of close graded granular materials (Stone aggregate - 25mm nominal size - 17.5%, Stone aggregate - 10mm nominal size - 17.5%, Crushed Stone - 2.36mm to 12.5mm - 25%, Stone chippings / screenings - 4.75mm nominal size - 20%, Stone chippings / screenings - 150 micron nominal size - 20%), mixing properly after adding sufficient quantity of water, refilling in layers not exceeding 150mm, compacting properly at Optimum Moisture Content with Surface Plate Vibrator and disposing the excavated material etc. complete, including traffic control, providing caution boards and as per direction of Engineer-in-charge for road restoration works in pipeline leak sites. |
| 44 | 4.1.3:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-III)derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 45 | Supply of Materials |
| 46 | 100.98.460:Supply of CI Double Flanged Sluice Valve Conforming to IS 14846 - 2000, Sluice Valve with Cap PN 1.6, Size 150mm. |
| 47 | 100.98.463:Supply of CI Double Flanged Sluice Valve Conforming to IS 14846 - 2000, Sluice Valve with Cap PN 1.6, Size 300mm. |
| 48 | OD188807/2025-2026:Supplying good quality 80mm GI BEND |
| 49 | Construction of Valve Chamber |
| 50 | 2.9.1:Excavation work by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50 m.Ordinary rock |
| 51 | 4.1.5:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 52 | 5.1.3:Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 53 | 5.1.2:Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 54 | 5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete |
| 55 | 5.9.2:Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. |
| 56 | 5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more |
| 57 | 13.7.1:12 mm cement plaster finished with a floating coat of neat cement of mix:1:3 ( 1 cement : 3 fine sand) Please Enable Macros to View BoQ information |
