|
| 1 | CIVIL WORKS |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual meansover areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan)including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5m, as directed by Engineer-in-charge.All kinds of soil |
| 3 | Providing and laying in position cement concrete of specified grade excluding thecost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mmnominal size derived from natural sources) |
| 4 | Centering and shuttering including strutting, etc. and removal of formfor:Foundations, footings, bases of columns, etc for mass concrete |
| 5 | Steel reinforcement for R.C.C work including straightening, cutting, bending, placingin position and binding all complete upto plinth levelThermo - Mechanically Treatedbars of grade Fe-500D or more |
| 6 | Providing and laying in position specified grade of reinforced cement concrete,excluding the cost of centering, shuttering, finishing and reinforcement - All work upto plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mmnominal size derived from natural sources) |
| 7 | 12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) |
| 8 | Filling available excavated earth (excluding rock) in trenches, plinth, sides offoundation etc. in layers not exceeding 20 cm in depth, consolidating each depositedlayer by ramming and watering, lead up to 50 m and lift up to 1.5 m. |
| 9 | Fabrication supply, conveyance & installation of Granite name board indicatingthe cost involved, the commencement, completion and inauguration date etc |
| 10 | Supply and fixing of name board with angles, flats, square pipe, ACP sheet includingnut and bolts. 2 nos per mast, 1Sqm in area. |
| 11 | ELECTRICAL WORKS |
| 12 | Supply installation testing and commissioning of Octogaonal Pole made of hot dipgalvanised GI sheet 70mm top diameter. 130mm bottom diameter thickness 3mmbase plate dimensions of 200x200x16mm suitable for windspeed as per IS 875 PartIII fixed head frame including round arm luminary carriage suitable to install 4/6 nosluminaries in symmetrical arrangement including connector foundation bolt 4 nosexisting RCC foundation and junction box etc, complete 8 Meters |
| 13 | Installation, testing and commissioning of 150W LED Flood light output greater than 105lumen/W 4000-6000 K with IP 66 protection LED Chip make Cree/Lumilled/Nichea with power factor greater than 0.95 at full load, internal surge protection up to 8 KV,and Aluminium pressure die-cast Powder coated housing, acrylic cover complete with THD less than 10%, power factor greater than 0.98, RoHS compliant, duly wired up for use on 230 V AC supply. Driver compartment should be seperatly accessible for maintenance (LM 79&80 certificates from NABL accredited Third party lab to be produced mentioning chip manufacturer) |
| 14 | Supply and fabrication conveyance and installation of angle iron frame work for wallmounting panel board |
| 15 | Fabrication, supply, conveyance, installation testing and commissioning of floor orwall mounting, dust and vermin proof, cubicle type MV panel board comprising ofthe following components/ devices & complying to IS 8623.Fabrication of fully partitioned, dust and vermin proof enclosure for panel assembly as per form 4 of IS 8623 (with latest amendments) using CRCA sheet as per approveddesign and requirement, with front and rear access facility, bus bar chambers, hingeddoors for all switch gear compartments, earthing the doors using 4 sq mm braidedcopper conductor, providing necessary cut-outs for mounting meters, relays,indication lamps, bus bar interconnection etc, detachable covers for bus bar chamberand cable alley, powder coating the assembly after subjecting to 7 tank process etc asrequired. CRCA sheet alone be used for the fabrication. Angles/ flats/ slotted anglesetc shall not be used for the fabrication of panel assembly. The measurments will betaken the area of the complete sheets used for panel board including partitions,folding, shrouding etc.Supply and fabrication of MV panel board using 1.6mm CRCAsheet, powder coated (excluding base frame) |
| 16 | Supply and providing heavy duty 'A' section neoprene gasket in the panelboardU' section rubber beeding suitable for 1.60/ 2.00 mm sheet |
| 17 | Supply and installation of a Digital timer, operating at 220-250 VAC, 50Hz, with a25A/1.5HP capacity. It features 5 On/Off program settings for daily and weeklyschedules, along with manual start, ON delay, and OFF delay settings. Equippedwitha high-precision, industrial-grade chip and strong anti-interference capabilities,the timer can automatically turn on and off the power supply of various electricalequipment according to the time set by the user. The controlled objects can includestreet lights, light boxes, neon lights, and high/mini mast systems. It also includes asufficient battery backup for time memory in case of power failure, and comes withsuitable fittings for use in a distribution box or MV panel with FRLS PVC insulated 5mm single core cable suitable for control wiring towards contactor |
| 18 | Supply and installation of a double pole 25A Contactor, rated for 220-250 VAC.50Hzoperation. It can control street lights, light boxes, neon lights, high/mini mast systems,and induction loads. |
| 19 | Supply and installation of an IP20 Surge Protective Device (SPD) with suitablefittings for a distribution box or MY panel. Specifications include: Voltage ProtectionLevel (Up), Nominal Voltage: 230V. UOC, LOKV. L-N: 7kV, L-PE: 7KV, N-PE:7KV Nominal Discharge Current (8/20µs): 10kA. Total Discharge Current(8/20µs): 60kA. Response Time: <.35 ns. Ambient Temperature(Ta): -10 to 55° C |
| 20 | Supply and fixing HRC fuse base of 32 A using suitable nut and bolt. 32 A 2-wayneutral links mounted on DMC/SMC base |
| 21 | Supplying and fixing following rating, double pole, (single phase and neutral),240volts, residual current circuit breaker (RCCB), having a sensitivity current 30 milliamperes in the existing MCB DB complete with connections, testing andcommissioning etc. as required.40 amps |
| 22 | Supplying and fixing 5A to 32 A rating, 240/415 volts, 10 kA, \\"\\"C\\"\\" curve, miniaturecircuit breaker suitable for inductive load of following poles in the existing MCBDB complete with connections, testing and commissioning etc. as required.Double pole |
| 23 | Supplying and fixing 5A to 32 A rating, 240/415 volts, 10 kA, \\"\\"C\\"\\" curve, miniaturecircuit breaker suitable for inductive load of following poles in the existing MCBDB complete with connections, testing and commissioning etc. as required.Single pole |
| 24 | Supplying and fixing following rating, double pole, 240 volts, isolator in the existingMCB DB complete with connections, testing and commissioning etc. as required.40amps |
| 25 | Supply and drawing the following sizes of multi-core PVC insulated & FRLSPVC sheathed 650/1100 V grade copper conductor round flexible cables conformingto IS 694 part I 1960 in the existing surface / recess conduit as required includinggiving necessary connections of the following sizes.3 core 1.50 sq mm |
| 26 | Supply and drawing the following sizes of multi-core PVC insulated & FRLSPVC sheathed 650/1100 V grade copper conductor round flexible cables conformingto IS 694 part I 1960 in the existing surface / recess conduit as required includinggiving necessary connections of the following sizes.3 core 2.50 sq mm |
| 27 | Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, andproviding masonry enclosure with cover plate having locking arrangement andwatering pipe etc. (but without charcoal/ coke and salt ) as required. |
| 28 | Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required3.15 mm copper conductor ( 10SWG) |
| 29 | Supply and clamping the following sizes of strips on surface of wall / parapet/existing cable tray using clamps fabricated from 20 x3 mm GI flat duly painted orheavy duty GI spacer saddles, spacing of clamps not exceeding 1 m , making good thedamages, colour washing etc. as required ( for vertical run).25 x 3 mm GI strip |
| 30 | Supply of superior quality copper earth socket for the following size of earthconductor including crimping etc. as required.3.15 mm (10 SWG) |
| 31 | Supply & laying of one number PVC insulated and PVC sheathed armouredaluminium power cable of 1.1KV grade of the following sizes in ground includingexcavation of trench of size 35 x 75 cm, refilling the trench etc. as required butexcluding sand cushioning and protective covering (in ordinary soil).3 core 6 sq mm |
| 32 | Supplying, laying and jointing of the following sizes of double wall corrugated(DWC) pipes made out of HDPE conforming to IS 14930 Part II for mechanicalprotection to underground power cables with all required accessories in ground in theexisting trench50/38 mm or nearest size |
| 33 | Supplying and making end termination with brass compression gland and aluminiumlugs forfollowing size of PVC insulated and PVC sheathed/XLPE aluminiumconductor cable of 1.1 KV grade as required. 3 X 6 sq. mm (19mm) |
| 34 | Supply and installation of 5A, 220V voltage protector (1100W) with auto cut-off at280V/140V, LED indicator, fast response time (2s), and compact design(73×44×30mm). Includes testing and commissioning. |
| 35 | Supply and panel board wiring - 4 sq.mm ring type leg, 2.5 sq.mm wire, 0.5 sq.mmwire, 1.5 sq.mm non insulated CP-1 pin terminal with suitable size heat shrink, 2.5sq.mm non insulated CP-1 pin terminal with suitable size heat shrink including wirecutting, leg crimping, sleeving, component fixing and wiring testing and packing |
| 36 | EXCLUSIVE OF GST Please Enable Macros to View BoQ information |
