|
| 1 | Earth work excavation for foundation by manual means for Isolated, Combined and Other type foundations in all soils and sub-soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring shuttering, bailing out water wherever necessary and depositing the surplus earth within the compound in places shown by the departmental officers with an initial lead of 10 mts and initial lift of 2.00mts. and clearing and levelling the site, etc., complete complying with standard specification and as directed by the departmental officers. |
| 2 | Supplying and filling in foundation, basement, etc with filling crushed stone sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers. |
| 3 | Cement Concrete 1:5:10 (One Cement, Five crushed stone sand and Ten hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick well rammed, consolidated and including curing etc. complete complying with standard specification and as directed by the departmental officers. -Mixing by mechanical means |
| 4 | Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, Sill slabs etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3mm for boarding, laid with silver oak joists of size 10cm x 5cm & 7.5cm x 5cm as support runner , vertical stiffener, side support and Top Horizontal stiffener spaced at about 60cm to 90cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid) |
| 5 | Supplying and erecting steel centering including necessary supports For plane surfaces such as rectangular or square RCC columns etc. which require only nominal strutting using mild steel sheets made of 10 gauge thick welded with MS angle size 40mm x 40mm x 5 mm and supported by Steel Adjustable Telescopic Props of Size 2m x 2m (expandable upto 3.60m) made with outer steel pipe with dia 50mm (3.60mm thick) and inner steel pipe with dia 40mm (2.90mm thick).etc..complete in all floors complying with standard specifcation. Steel Adjustable telescopic props shall be rovided as directed by the departmental Officers. (Payment for centering shall be given after the concrete is laid) |
| 6 | Providing and laying in position, standardised concrete Mix M-25 Grade using In-situ Concrete batching plant/ Ready Mix Concrete (RMC) adopting weigh batch method in accordance with IS 456 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 kg/m3 and maximum water cement ratio of 0.55, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete,improve workability without impairing strength and durability with about (5 Cu.m) 7730 kg. of 20mm machine crushed stone jelly and with about (3.3 Cu.m) 5156 kg. of 10- 12mm machine crushed stone jelly and with about (4.79 cu.m) 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including Conveyance of concrete from batching plant to Work site, Electricity charges and other works & labour cost involved for concrete production, laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS standards. (No separate payment will be made by the Department for the excess usage of materials).(1:1.5:3 mix) |
| 7 | Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel reinforcement grills of all variety like HYSD/CTD/TMTand all grade like Fe 500, Fe550D, Fe 500 D etc., for all RCC works as per design given including cost of steel reinforcement and G.I. binding wire, wastage etc. complete complying with standard specification and as directed by the departmental officers.(Contractor has to make his own arrangements for the supply of steel reinforcement and binding wire) |
| 8 | Supplying and fixing Mild Steel grills Petty Iron works for Truss, straps including cost of steel and labour charges for welding etc., complete and as directed by the departmental officers |
| 9 | Plain Cement Concrete 1:2:4 (one cement, two crushed stone sand and four hard broken stone jelly) using 20mm jelly for wearing coat including laying, compacting, finishing and curing, etc., complete as per standard specificatins and as directed by the departmental officers.-Mixing by mechanical means |
| 10 | Supplying , fixing and roofing with colour galvalume sheet of 0.47mm thick with all necessary accessories such as J/V bolt and nuts of suitable length with suitable bitumen washers complete complying with standard specification and as directed by the departmental officers. |
| 11 | Providing Supplying fabricating and fixing in position of Alco panelling for exterior glading work using also panell sheet 4mmtk with required colour and internal frame using aluminium rectangular box section of size 63.50mmx 38.10mmx2mm at 1.054/m and necessary aluminium 'L' angle screws , rubber materials .The aluminium frames are properly fixed into the wall or R.C.C column making necessary screws at suitable intervals . The Alco panel sheet are fixed into the aluminium frame and pasting the rubber materials . The above rates are including cost of all kind of materials scafolding charges and labour charges etc; complete. |
| 12 | Supplying and Fixing of MS Powder Coated Waiting Chair- Three seater with arm Rest of of comfortable 3-seater waiting/visitor chairs. Designed for durability and comfort, our chairs provide ergonomic support and a stylish look, perfect for Airport, lobbies, reception areas, and waiting rooms. Enhance your space with our reliable, high-quality seating solutions and Required size including cost of Materials and labour charges in etc., Complete |
| 13 | Wiring with 2x1.5sqmm (22/0.3) PVC insulated unsheathed SC Cu. Conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with TW switch boc 5A F.T. switch inflush with wall covered with hylum sheet of 3mm thick with painting of suitable color for concealed PVC light / fan point (for elctronic regulator) SD-24. |
| 14 | Wiring with 2X 1.5 sqmm (22/0.3) PVC insulated Sc unsheathed Cu. Conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories and with 150x100x113mm TW switch box and 5A 3 pin non inter locking CS plug with painting of suitable color with continuous earth wire connection of 14SWG TC wire for concealed PVC plug point ( SD-38) |
| 15 | Supply and run of 2 of 4 sqmm (56/0.3) PVC insulated SC unsheathed cu. Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection by 14 SWG TC wire and making good of the concealed portion with suitable color SD-65 |
| 16 | Supply and fixing LED INDOOR FITTINGS (LIGHT EMITTING DIODE) HIGHER END of 24W LED 4000K 2 x 2 Square Type Recessed Fitting with LED ceiling with PVC unsheather copper leads from terminals -M-1284 |
| 17 | Paving the floor with best approved quality fine polished Kota stone slabs of size 600 x 600 and above 20mm thick with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone sand) with required Cement Slurry and Mortar Plasticizer fixing the slabs in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments and polishing with floor polisher to a high degree of finish etc., complete complying with standard speicification and as directed by the departmental officers.(The kota stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work) |
| 18 | Supplying and Fixing of Aluminium Diecast Letters of approved size and colour. The colour treatment process is achieved with colour coat and then the processed coloured layer is set into the kiln for the heat treatment process for the following sizes etc complete () |
| 19 | 60cm Tamil Stainless Steel Letters |
| 20 | 25cm Tamil Stainless Steel Letters |
| 21 | Hot dip Galvanizing of PEB Structures firstly sand blasted and further galvanised with the raw material confirming to the following specifications – Silicon - 0 to 0.4%, Carbon - <0.25%, Phosphorous- <0.05% & Manganese- <1.3 %.) (Thickness 8mm & Above) Average Coating Thickness 85 Microns over this Treated with epoxy of 100microns (approx) Including transport, lifting charges and delivery at site . Please Enable Macros to View BoQ information |
