|
| 1 | SUB HEAD:: SITE DEVELOPMENT: |
| 2 | Clearing and Grubbing Road Land .(Clearing and grubbing road land including uprooting rank vegetation, grass, bushes, shrubs, saplings and trees girth up to 300 mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned up to a lead of 1000 metres including removal and disposal of top organic soil not exceeding 150 mm in thickness.) By Manual Means: In area of light jungle |
| 3 | SUB-HEAD:: BUILDING PORTION GROUND FLOORSUB HEAD: EARTHWORK IN EXCAVATION: Earth work in excavation in foundation and trenches etc. in all kinds of soil (excluding soil containing 50% or more of shingle or small size boulders upto 30 cm size, saturated soil and rock), lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers, when required, into plinth sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus soil as directed within a lead of 50m. |
| 4 | Re-filling excavated earth in foundations and plinth etc. in 15 cm layer including ramming and watering etc. complete. |
| 5 | SUB HEAD: CEMENT CONCRETE WORK:Providing and laying in foundations and plinth cement concrete 1 : 4 : 8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering. |
| 6 | Providing and laying cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) excluding the cost of centring an shuttering in:b) Walls including attached buttresses, pilasters and their caps and bases and string courses etc. up to floor two level.(Wall) |
| 7 | SUB HEAD :: RCC WORK: Reinforced concrete work in foundations, footings, bases of columns etc. and mass concrete excluding cost of centring, shuttering and reinforcement in : 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size). |
| 8 | Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but exluding cost of centring, shuttering and reinforcement.c) 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size). |
| 9 | Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement.1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size). |
| 10 | Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement with 1 : 2 : 4 (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size). |
| 11 | Reinforced cement concrete work in stair cases (excluding landing) except spiral cases including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface, preparing of the top surface and finishing, nosing upto floor two level but excluding the cost of centring, shuttering and reinforcement with 1 : 2 : 4 (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size). |
| 12 | SUB HEAD::BRICK WORKS: Brick work with best available local bricks in plinth and in Superstructure in cement mortar 1:4 (1 cement : 4 fine sand). |
| 13 | SUB HEAD :: STEEL WORK: Reinforcement of RCC work including bending, binding and placing in position complete. |
| 14 | Steel work in built up tubular trusses including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer welded and bolted including special shaped washers etc complete (welding to be paid separately). |
| 15 | SUB-HEAD:: FLOORING: Providing and laying in foundations and plinth cement concrete 1 : 4 : 8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering. |
| 16 | Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., completed) Size of Tile 1000x1000 mm |
| 17 | Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with : a) Makrana white second quality |
| 18 | Chequrred terrazzo tiles 22 mm thick with marble chips of sizes upto 6mm in floors on 25 mm thick bed mortar 1 : 3 (1 cement : 3 coarse sand) jointed with neat cement slurry mixed with pigment to match the shade of the tiles including rubbing and polishing complete:a) Light shades using white cement |
| 19 | White glazed tiles 5mm.thick in flooring, skirting, risers of step and dado in 12 mm thick cement plaster 1 : 3(1 cement: 3 coarse sand) painted with white cement slurry. |
| 20 | SUBHEAD::EARTH SAND FILLING: Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete. |
| 21 | SUB HEAD::DRAINAGE & PLINTH PROTECTION: Construction of cement concrete drain 30 cm wide and 23 cm deep in cement concrete 1 : 3 : 6 (1 cement : 3 sand : 6 hard graded stone chips/shingle 40 mm and down gauge) 8 cm thick on sides and bottom and plastering on all exposed surfaces with 12 mm thick cement mortar1 : 3 (1 cement : 3 fine sand) including shuttering complete. |
| 22 | Making plinth protection 50 mm thick of cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 stone aggregate using 20 mm nominal size) over 75 mm bed of stone ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finsihing the top smooth. |
| 23 | SUB HEAD :: DOORS & WINDOWS: Providing and fixing Aluminium glazed door shutters of approved brand or as directed by the Engineer in charge. |
| 24 | Providing and fixing Aluminium glazed Windows of approved brand or as direction by the Engineer in charge |
| 25 | SUB HEAD: WOOD WORK: Centring and shuttering including strutting, propping etc and removal of form work for : a) Foundation, footings, bases of columns etc. and mass concrete. |
| 26 | b) Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. |
| 27 | c) Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5 m height). |
| 28 | d) Lintels, beams, girders, bressumers and cantilevers etc. |
| 29 | e) Column, pillars, posts and struts etc. |
| 30 | SUB HEAD: FINISHING: 15 mm cement plaster 1 : 4 (1 cement : 4 fine sand) on the rough side of single or half brick wall. |
| 31 | Neat cement punning. |
| 32 | Providing two coats of acrylic water based wall putty/ wall filler of Asian Paits/ Berger/ Dulux over concrete/ cement plaster/ brick walls and ceilings both internal and external after removing all the loosely adhering material from the wall/ ceiling surface with the halp of emery stone, putty blade or wire brush, moistening the wall with the help of sufficient quantity of clear water as specified and directed by the department. |
| 33 | Applying one coat of cement primer of approved brand and manufacture on wall surface. |
| 34 | Finishing walls with water proofing cement paint of approved brand and manufacture and required shade on new work (three or more coats) to give an even shade. |
| 35 | SUB HEAD: FIRST FLOOR BUILDING PORTION: Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but exluding cost of centring, shuttering and reinforcement.c) 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size). |
| 36 | Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement.1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size). |
| 37 | Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement with 1 : 2 : 4 (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size). |
| 38 | Reinforced cement concrete work in stair cases (excluding landing) except spiral cases including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface, preparing of the top surface and finishing, nosing upto floor two level but excluding the cost of centring, shuttering and reinforcement with 1 : 2 : 4 (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size). |
| 39 | SUB HEAD::BRICK WORKS: Brick work with best available local bricks in plinth and in Superstructure in cement mortar 1:4 (1 cement : 4 fine sand). |
| 40 | SUB HEAD::STEEL WORK: Reinforcement of RCC work including bending, binding and placing in position complete. |
| 41 | Steel work in built up tubular trusses including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer welded and bolted including special shaped washers etc complete (welding to be paid separately). |
| 42 | SUB HEAD::FLOORING: Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting the joints with white cement and matching pigments etc., completed) Size of Tile 1000x1000 mm |
| 43 | White glazed tiles 5mm.thick in flooring, skirting, risers of step and dado in 12 mm thick cement plaster 1 : 3(1 cement: 3 coarse sand) painted with white cement slurry. |
| 44 | Marble stone flooring with 18 mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with : a) Makrana white second quality |
| 45 | SUB HEAD::DOOR & WINDOWS: Providing and fixing Aluminium glazed door shutters of approved brand or as directed by the Engineer in charge. |
| 46 | Providing and fixing Aluminium glazed Windows of approved brand or as direction by the Engineer in charge |
| 47 | SUB HEAD::WOOD WORK: Centring and shuttering including strutting, propping etc and removal of form work for :c) Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5 m height).Timber used 8 times |
| 48 | d) Lintels, beams, girders, bressumers and cantilevers etc. |
| 49 | e) Column, pillars, posts and struts etc. |
| 50 | SUB HEAD:FINISHING: 15 mm cement plaster 1 : 4 (1 cement : 4 fine sand) on the rough side of single or half brick wall. |
| 51 | Providing two coats of acrylic water based wall putty/ wall filler of Asian Paits/ Berger/ Dulux over concrete/ cement plaster/ brick walls and ceilings both internal and external after removing all the loosely adhering material from the wall/ ceiling surface with the halp of emery stone, putty blade or wire brush, moistening the wall with the help of sufficient quantity of clear water as specified and directed by the department |
| 52 | Applying one coat of cement primer of approved brand and manufacture on wall surface. |
| 53 | Finishing walls with water proofing cement paint of approved brand and manufacture and required shade on new work (three or more coats) to give an even shade. |
| 54 | SUB HEAD :: HEAD ROOM SUB HEAD::RCC WITH 1:2:4 WORKS: Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but exluding cost of centring, shuttering and reinforcement.c) 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size). |
| 55 | Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement.1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size). |
| 56 | Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement with 1 : 2 : 4 (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size). |
| 57 | Reinforced cement concrete in walls (any thickness) including attached pillasters, buttresses, plinth and string course, fillets etc from top of foundation up to floor two level including finishing and plastering the exposed surfaces with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface excluding cost of centring, shuttering and reinforcement in :1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size). |
| 58 | SUB HEAD::BRICK WORKS: Brick work with best available local bricks in plinth and in Superstructure in cement mortar 1:4 (1 cement : 4 fine sand). |
| 59 | SUB HEAD::STEEL WORK: Reinforcement of RCC work including bending, binding and placing in position complete. |
| 60 | Steel work in built up tubular trusses including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer welded and bolted including special shaped washers etc complete (welding to be paid separately). |
| 61 | SUB HEAD::FLOORING: 25mmthickcement concrete flooring 1 : 2 : 4 (1 cement : 2 coarse sand : 4 graded stone shingle 12.5 mm nominal size) finished with a floating coat of neat cement. |
| 62 | SUB HEAD::DOOR & WINDOWS: Providing and fixing Aluminium glazed door shutters of approved brand or as directed by the Engineer in charge. |
| 63 | Providing and fixing Aluminium glazed door shutters of approved brand or as directed by the Engineer in charge. |
| 64 | Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in bothdirections with wire of dia. 0.50 mm all complete. |
| 65 | SUB HEAD::WOOD WORK: Centring and shuttering including strutting, propping etc and removal of form work for :c) Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5 m height). |
| 66 | d) Lintels, beams, girders, bressumers and cantilevers etc. |
| 67 | e) Column, pillars, posts and struts etc. |
| 68 | SUB HEAD:FINISHING:15 mm cement plaster 1 : 4 (1 cement : 4 fine sand) on the rough side of single or half brick wall. |
| 69 | Providing two coats of acrylic water based wall putty/ wall filler of Asian Paits/ Berger/ Dulux over concrete/ cement plaster/ brick walls and ceilings both internal and external after removing all the loosely adhering material from the wall/ ceiling surface with the halp of emery stone, putty blade or wire brush, moistening the wall with the help of sufficient quantity of clear water as specified and directed by the department |
| 70 | Applying one coat of cement primer of approved brand and manufacture on wall surface. |
| 71 | Finishing walls with water proofing cement paint of approved brand and manufacture and required shade on new work (three or more coats) to give an even shade. |
| 72 | Neat cement punning. |
| 73 | SUB HEAD:SANITARY INSTALLATION: Making soak pit 2.50 m dia 3 m deep with 45 x 45 cm dry brick honeycomb shaft and SW drain pipe 100 mmdia 1.80 m long complete as per standard design. |
| 74 | Providing and fixing white vitreous china pedestal type (European type WC pan) water closet with seat and lid with CP brass hinges and rubber buffers, 12.5 Litres white vitreous china low-level flushing cistern with fittings and brackets 40 mm white porcelain in enamel led flush band, 20 mm over flow pipe with specials and mosquito proof coupling of approved municipal design complete including cutting and making good the walls and floors where required. |
| 75 | Providing and fixing CP Brass waste for wash basin and sinks (b) 40 mm dia |
| 76 | Providing and fixing MI Fisher union for wash basin |
| 77 | Providing and fixing CP brass or MI trap for wash basin and sinks. |
| 78 | Providing and fixing sand Cast iron/cast iron(spun) soil, waste and Vent Pipes. (a) 100 mm dia |
| 79 | Providing and laying cement concrete 1 : 5 : 10(1 cement : 5 lime sand : 10 graded stone aggregate 40 mm nominal size) all around SW Pipe including bed concrete 15 cm thick as per standard design. a) 100 mm dia SW pipes |
| 80 | Providing and fixing white vitreous china wash basin with RS or CI brackets painted white 15 mm CP brass pillar taps and CP brass chain with rubber plug 32 mm CP brass waste of standard pattern, 32 mm dia CP brass trap and MI unions complete, including cutting and making good the walls where required.a) Flat back wash basin size 550x400 mm with a pair of 15 mm CP brass pillar taps of heavy quality. |
| 81 | Constructing brick masonry manhole with 2nd class bricks in cement mortar1 : 5 (1 cement :5 fine sand) RCC top slab with 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 stone single 20 mm nominal size), foundation concrete1:4: 8 mix (1 cement : 4 coarse sand : 8 stone aggregate 40 mm nominal size) inside plastering 12 mm thick with cement mortar 1 : 3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement and making channels in cementc oncrete1:2:4mix(1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size) neatly finished complete as per standard design. a)Insidesize90x80cmand45cmdeepincludingCIcoverwithframe(light duty) 455 x 610 mm internal dimensions total weight of cover and frame to be not less than 38 Kg (weight of cover and frame to be not less than 38 kg, (weight of cover 23 Kg and weight of frame 15 Kg). |
| 82 | Providing and fixing 600x450 mm bevelled edge mirror or superior glass (of approved quality) complete with 6 mm thick asbestos sheet ground fixed to wooden cleadt with CP brass screws and washers. |
| 83 | Providing and fixing toilet paper holder.a) CP Brass |
| 84 | SUB HEAD : WATER SUPPLY: Providing and fixing GI pipes complete with GI fittings and clamps including cutting and making good the walls (internal work).a) 15 mm nominal bore(internal work). |
| 85 | b) 20 mm nominal bore(Externall work). |
| 86 | h) 80mm nominal bore (External Work) |
| 87 | Providing and fixing brass stop cock of approved quality.a) 15 mm nominal bore |
| 88 | b) 20 mm nominal bore |
| 89 | e) 80 mm nomiinal bore |
| 90 | Providing and fixing brass bib cock of approved quality.15 mm nominal bore |
| 91 | Providing ,Fixing ,commissioning & testing of 1 H.P. 1 Phase pump(SWJ 1 ) including control Panel and all accesories or as directed by Engg. i/c |
| 92 | Providing fixing best quality PVC sintex 1000 ltrs catpacity |
| 93 | SUB HEAD: SSEPTIC TANK (Size 3.8x2.8x1.8 Mtrs) : Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers when required, into plinth, sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated soil as directed within a lead of 50m. |
| 94 | Re-filling excavated earth in foundations and plinth etc. in 15 cm layer including ramming and watering etc. complete. |
| 95 | Providing and laying in foundations and plinth cement concrete 1 : 4 : 8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering. |
| 96 | Providing and laying cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) excluding the cost of centring an shuttering in:b) Walls including attached buttresses, pilasters and their caps and bases and string courses etc. up to floor two level.(Wall) |
| 97 | Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement with M20 (1 cement : 1.5 coarse sand : 3 stone shingle 20 mm nominal size). |
| 98 | Reinforcement of RCC work including bending, binding and placing in position complete. |
| 99 | Brick work with best available local bricks in plinth and in Superstructure in cement mortar 1:4 (1 cement : 4 fine sand). |
| 100 | 12 mm cement plaster 1 : 4 (1 cement : 4 fine sand). |
| 101 | Neat cement punning. |
| 102 | Centring and shuttering including strutting, propping etc and removal of form work for :c) Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5 m height). |
| 103 | SUB HEAD: UNDERGROUND WATER STORAGE TANK (SIZE 2X2X1.8 Mtrs): Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers when required, into plinth, sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated soil as directed within a lead of 50m. |
| 104 | Re-filling excavated earth in foundations and plinth etc. in 15 cm layer including ramming and watering etc. complete. |
| 105 | Providing and laying in foundations and plinth cement concrete 1 : 4 : 8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering. |
| 106 | Providing and laying cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) excluding the cost of centring an shuttering in:b) Walls including attached buttresses, pilasters and their caps and bases and string courses etc. up to floor two level.(Wall) |
| 107 | Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement with M20 (1 cement : 1.5 coarse sand : 3 stone shingle 20 mm nominal size). |
| 108 | Reinforcement of RCC work including bending, binding and placing in position complete. |
| 109 | Brick work with best available local bricks in plinth and in Superstructure in cement mortar 1:4 (1 cement : 4 fine sand). |
| 110 | 12 mm cement plaster 1 : 4 (1 cement : 4 fine sand). |
| 111 | Neat cement punning. |
| 112 | Centring and shuttering including strutting, propping etc and removal of form work for : |
| 113 | Sentry Post SUB HEAD::EARTHWORK: Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers when required, into plinth, sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated soil as directed within a lead of 50m. |
| 114 | Re-filling excavated earth in foundations and plinth etc. in 15 cm layer including ramming and watering etc. complete. |
| 115 | SUB HEAD::CEMENT CONCRETE WORK: Providing and laying in foundations and plinth cement concrete 1 : 4 : 8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering. |
| 116 | Providing and laying cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) excluding the cost of centring and shuttering in: b) Walls including attached buttresses, pilasters and their caps and bases and stringcourses etc. up to floor two level. |
| 117 | SUB HEAD :: RCC WORK:Reinforced concrete work in foundations, footings, bases of columns etc. and mass concrete excluding cost of centring, shuttering and reinforcement in : 1 : 2 : 4 (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size). |
| 118 | Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but exluding cost of centring, shuttering and reinforcement.c) 1 : 2 : 4 (1 cement : 2 coarse sand : 4 stone shingle 20 mm nominal size). |
| 119 | Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement. a) M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size) |
| 120 | SUB HEAD::BRICK WORKS: Brick work with best available local bricks in plinth and in Superstructure in cement mortar 1:4 (1 cement : 4 fine sand). |
| 121 | SUB HEAD :: STEEL WORK: Reinforcement of RCC work including bending, binding and placing in position complete. |
| 122 | Steel work in built up tubular trusses including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer welded and bolted including special shaped washers etc complete (welding to be paid separately). |
| 123 | SUB-HEAD:: FLOORING: Providing and laying in foundations and plinth cement concrete 1 : 4 : 8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering. |
| 124 | Cement concrete flooring 1 : 2 : 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement.40 mm thick |
| 125 | SUB HEAD::DRAINAGE & PLINTH PROTECTION: Construction of cement concrete drain 30 cm wide and 23 cm deep in cement concrete 1 : 3 : 6 (1 cement : 3 sand : 6 hard graded stone chips/shingle 40 mm and down gauge) 8 cm thick on sides and bottom and plastering on all exposed surfaces with 12 mm thick cement mortar1 : 3 (1 cement : 3 fine sand) including shuttering complete. |
| 126 | Making plinth protection 50 mm thick of cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 stone aggregate using 20 mm nominal size) over 75 mm bed of stone ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finsihing the top smooth. |
| 127 | SUB HEAD :: DOORS & WINDOWS: Providing and fixing Aluminium glazed door shutters of approved brand or as directed by the Engineer in charge. |
| 128 | Providing and fixing Aluminium glazed Windows of approved brand or as direction by the Engineer in charge |
| 129 | SUB HEAD::WOOD WORK: Centring and shuttering including strutting, propping etc and removal of form work for :Ceiling Frame in X and Y Directions. |
| 130 | Centring and shuttering including strutting, propping etc and removal of form work for :a) Foundation, footings, bases of columns etc. and mass concrete. |
| 131 | b) Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc. |
| 132 | d) Lintels, beams, girders, bressumers and cantilevers etc. |
| 133 | e) Column, pillars, posts and struts etc. |
| 134 | SUB HEAD:FINISHING: 12 mm cement plaster 1 : 4 (1 cement : 4 fine sand). |
| 135 | Neat cement punning. |
| 136 | Distempering (two or more coats) with oil bound washable distemper of approved brand and manufacture and of required shade on new work over and including a priming coat with distemper primer of approved brand and manufacture to give an even shade. |
| 137 | Providing and fixing 2.50 cm thick approved local wood eaves boards 23 cm wide with necessary mouldings etc. |
| 138 | Providing and fixing, fly proof galvanized MS wire gauge of IS gauge designation 85 g with wire of dia 0.56 mm to windows and clerestory windows including 62 x 19 mm beading of best available local wood.( for bird proof wire mesh beneath and around CGI sheet for 1st floor) |
| 139 | SUB HEAD::ROOFING: Providing and fixing Durashine zinc-Aluminium alloy coated (TATA) Bluescope building product) sheet roofing fixed with necessary fasteners and lapping method as described by the manufacturer inclusive of cutting hoisting and fixing complete, excluding the cost of purlins, rafters and trusses.Details of cost for 179.655 Sq.m.Laying and fixing 20 sheets in 3 row require Overall Sheet area of 20 x 3 x 3.05 x 1.072 plus 3% wastages = 202.061 Sqm After H & L laping as per manufacturer's specification, effective Area Measurable will be 20 x 3x 2.95 x 1.015 = 179.655 Sqm |
| 140 | Providing and fixing Durashine zinc-Aluminium alloy coated (TATA) Bluescope building product) sheet roofing fixed with necessary fasteners and lapping method as described by the manufacturer inclusive of cutting hoisting and fixing complete, excluding the Details of cost for 11.75m Laying and fixing 4 lenths of 3.05m each require Overall length of 4 x 3.05 plus 3% wastages = 12.566m After laping as per manufacturer's specification, effective Measurable lengthwill be (4 x 3.05) - (3 x 0.15) = 11.75m |
| 141 | Providing and fixing 3 mm thick hard board sheet ceiling of approved quality with necessary nails etc. complete (frame work to be paid separately). |
| 142 | SUB-HEAD:: CC PAVEMENT ROAD: Preparation of sub grade by excavating earth to an average depth of 22.50 cm,dressing to camber and consolidating with road roller, making good the undulations etc. and disposal of surplus earth, lead upto 50 m. |
| 143 | Consolidation of sub-grade with road roller of 8 to 12 tonne capacity including making good the undulations etc. with earth or quarry spoils etc. and rerolling the sub grade |
| 144 | Construction of granular sub-base by providing close graded Material, mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density,complete as per clause 401 |
| 145 | Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing, rolling with vibratory roller 8-10 tonnes in stages to proper grade and camber, applying and brooming requisite type of screening/ binding Materials to fill up the interstices of coarse aggregate, watering and compacting to the required density.)A )By Manual Meansb) Using Screening Type-A (13.2mm Agg.) |
| 146 | Cement Concrete Pavement (Construction of un-reinforced, dowel jointed, plain cement concrete pavement over a prepared sub base with 43 grade cement @ 400 kg per cum, coarse and fine aggregate conforming to IS 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or slip form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, dowel bar, tie rod, admixtures as approved, curing compound, finishing to lines and grades as per drawing ) |
| 147 | SUB HEAD::BOUNDARY WALL: Construction of Boundary Wall of 2.1 mtr height as per specification and drawing |
| 148 | Construction of Mild Steel Gate as per specification and drawing. Please Enable Macros to View BoQ information |
