|
| 1 | Air Swing: Providing designing and fixing air swing in pair of size 1150 x 900 x 1250 mm fabricated with main post of 114mm dia and 2.5mm thick and rest of the pipes 40mm dia and 2.5 mm thick. All pipes made up of hot rolled tubular steel and hot dipped galvanized and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Handle bars are to be provided with high quality grip rubber. Pedals shall be made up of Nylon alloy with rounded edges to prevent any impact or injury. Seats and base plate cover to be made up from virgin LLDPE manufactured by rotational |
| 2 | Elliptica exerciser: Providing designing and fixing ellipticalexercise of size 1200 x 540 x 1600 mm fabricated withmain post of 114mm dia and 2.5mm thick and rest of thepipes 40mm dia and 2.5 mm thick. All pipes made up ofhot rolled tubular steel and hot dipped galvanized andpowder coated using Akzo Nobel or equivalent of 80-120micron thick. All joints of pipe are robotic welded with jointsscalloped as necessary and dressed off removing sharpedges and burrs. Zinc primer paint to be applied at allwelding points prior |
| 3 | Seated chest press: Providing designing and fixing of seated chest press in a pair of size 1800 x 700 x2000 mm fabricated with main post of 114mm dia and 2.5mm thick and rest of the pipes 40mm dia and 2.5 mm thick. |
| 4 | NS Item= Ornamental Canopy with base complete in all respect – with 6 No. Ornamental Design FRP Molded Pillar FRP base pedestal with vertical fitted design having base width of size 260mm x 260mm and height 900mm having 4 no. of size 20mm drilled in the base with hold fasts and having B class pipe of size 88 mm and height 2890mm, the central m.s pipe holds FRP Molded taj 6no of size 260 x 260 x 210mm high suitably mounted at appropriate height complete as per design. Complete pillar suitably grinded and subsequently spray painted with two coats of P.U Paints in required shade. (ii) 12 No. spndred and 6 no. Friezes Floral and Ornate decorative design combination of spandrel and frieze, matched to be suspended between two m.s pillars as per the design. The spandrel (L-Bracket) having length 420mm and height 400mm the frieze (Top Panel) height 250mm and length as per the size of the gazebo. The frieze mounted on m.s tabular pipe frame of size 50mm x 25mm, frieze properly welded to the column pillars at either ends. Complete set of spandrel and frieze uniformly grinded spray primered, spray painted with P.U Paints. (iii ) 3 No. cast iron/frp base panel railing with frame Floral and Ornate decorative design cast iron/frp side railing panel as per design having height of 730mm and length as per size of Gazebo. Each panel top and bottom mounted with mild steel tubular pipe frame of size 50 x 25 mm. The bottom mild steel pipe having 2 nos. of hold fasts in m.s pipe of size 40 x 40mm and length 250mm welded at the base to hold the panel in the ground. Every panel length is as per the gap between the two pillars. The complete railing panel grinded for neat surface finishes spray primered and subsequently spray painted with P.U Paint in required shade. (iv) One set of top frame with Double Finishing FRP Molded Plastic Sheet roof Top frame in m.s tubular pipe of size 40 x 40mm properly welded and grinded. The top frame mounted with FRP molded Sheet of 4 mm thick with top and bottom good finishing (Double finishing sheet) to make it rust proof bent to profile of size 245mm width in -Z- section on either ends fixed horizontally along the length between column pillars. Also it contain FRP Moulded Ball of 14”Dia x 2mm thick at the central top for its beautification. Each sheet enamel painted in red color. Each such sheet properly riveted to horizontal sheets. The complete item is fitting at site with installation and construction of canopy base should be made of earth work .15 m deep, Brick ballast .15 m depth,two steps of first class brick work 1:5 of 3.00 mX.30 mX.45 m and 3.00 m X.30 m X.60m, cement concerete on .10 height and finishing with checqurred tiles on the base and steps. (Including fixing at site and supervision and transportation and all type taxes) |
| 5 | Pull Chair:- Providing, and fixing of Pull pair of size 2500 X 800 X 2000 mm make of Green Gym or Equivalent fabricated with main post of 140 mm dia and 3.0 mm thick rest of the pipes are 40mm dia and 3.0 mm thick all pipes made up of hot roiled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc .primer paint to be applied at all welding points prior to finishing. Pedals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be` made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Officer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GULLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and J shaped welded bolts and once the concrete is set, fix theequipment on to it and cover nuts and bolts with the baseplate cover, all complete as per directions of Engineer in Charge. |
| 6 | Double Cross Walker/ Cross trainer double:- Providing, and fixing Double Cross Walker of size 1600 X 600 X 1600 mm make of Green Gym or Equivalent fabricated with main post of 140 mm dia and 3.0 mm thick rest of the G.I pipes are 40 mm dia and 2.5 mm thick all G.I pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of G.I pipes are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company like SKF to be approved by Officer -in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of G.I pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength N425 and J shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Engineer-in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc.` The rates are inclusive of all taxes like GST, Transportation, Installation in CC with 2 years defect liability period free of cost to full satisfaction of engineer in charge complete in all respect. |
| 7 | Twister:- Providing, and fixing Twister of size 1700 X 1300 X 1300 mm make of Green Gym or Equivalent fabricated with main post of 140 mm dia and 3.0 mm thick rest of the pipes are 40mm dia and 2.5 mm thick all pipes made up of hot rolled tubular steel and hot dipped galvanized, and powder coated using Akzo Nobel or equivalent of 80-120 micron thick. All welding joints of pipe are robotic welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. Zinc primer paint to be applied at all welding points prior to finishing. Padals shall be made up of Nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin LLDPE manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and U V resistant environmental friendly. Bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by Officer-in-Charge. Equipment to be fitted within built limiters to prevent unwanted movements. All open ends of pipe to be coloured by GI/LLDPE caps for user safety. The equipment to be fixed on ground with concrete of minimum strength M25 and ishapod welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of Officer -in-Charge regarding material, shape of equipment, colour on metal, seat and base cover plate and fixing of. equipment etc.`` ` |
| 8 | Cleaning, Desilting and making of walking track with other contingent works of Behrampur Pond under Ward no 16 Zone 1, MCG. Please Enable Macros to View BoQ information |
