|
| 1 | Excavation in foundations,trenches etc., in earth work, lift upto 1.50 mts. Stacking the excavated soil not more than 3 mts. Clear from the edge of the excavation & then returning the stacked soil in 15 cms. Layers,when required into plinths sides of foundation etc.,consolidating each deposited layers by ramming & watering & then disposing of all surplus excavated earth as directed within all leads & lifts as per entire satisfaction of Engineer in charge. |
| 2 | Providing and laying cement concrete 1:6:12 ( 1 cement : 6 sand: 12 graded stone aggregate 40mm nominal size) and curing complete excluding cost of form work in foundation and plinth within all leads and lifts as per the direction of Engineer-in-Charge. |
| 3 | Squared rubble masonery coursed with hard stone of approved quality in foundation and plinth including raking out joints in cement mortar 1 : 6 ( 1 cement : 6 sand) within all leads and lifts as per the direction of Engineer -in- Charge. |
| 4 | Brick work using common burnt clay building bricks of approved quality in super structure in cement mortar 1: 6 (1 cement : 6 sand) above plinth level up to floor two level (2nd class bricks) within all leads and lifts as per the direction of Engineer-in -Charge. |
| 5 | Steel work welded in built-up section, trusses and framed work including cutting hoisting, fixing in position and applying a priming coat of red lead paint in beams joists channels, angle cleats as in main and cross beam, hip and jack rafters, purlins connected to common rafters, steel gate and like within all leads and lifts as per the direction of Engineer-in- Charge. |
| 6 | Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm, so as to give a fair finish including centring, shuttering, strutting and propping etc., with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 mtr and removal of the same for insitu-reinforced concrete & plain concrete work in: |
| 7 | Flat surfaces such as soffits of suspended floors, roofs, landing and the line floor etc upto 200mm thickness complete in all respect within all eads and lifts as per direction of Engineer-in-charge. |
| 8 | Beam, cantilever, girders and lintles sides and soffits of beam haunching cantilever girder, bressumers and lintles not exceeding 1 mtr in depth complete in all respect within all leads and lifts as per direction of Engineer-in-charge |
| 9 | Providing and laying cement concrete work 1 : 2 :4 ( 1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) and curing complete excluding the cost of form work and reinforcement for reinforced concrete work in:- |
| 10 | Suspended floor roofs, landing & shelves and their support balconies,beams, girders, bressumers and cantilever upto floor two level within all leads and lifts as per the direction of Engineer-in-Charge. |
| 11 | Lintels, beams ,griders bressumers and cantilevers upto all floor level in all leads and lifts.as per direction of Engineer-in-charge |
| 12 | Pre-cast terrazo tiles 20mm.thick with marble chips of specified size fixed on wall 10mm.thick cement plastering 1:3(One Cement:Three Sand) jointed with neat cement slurry mixed with pigment to match the shade of tiles (where ever required) including rubbing and polishing complete with tiles of Grey shade in all leads and lifts.as per direction of Engineer-in-charge |
| 13 | 15mm thick cement plaster in single coat on fair side of brick/concrete/stone walls for interior plastering upto floor two level including arrises, internal rounded angles, chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth in cement mortar 1:6 (1cement:6sand) complete in all respect within all leads and lifts as per direction of Engineer-in-charge. |
| 14 | 6mm cement plaster to ceiling in cement mortar 1:3 (1cement : 3sand) complete in all respect within all leads and lifts as per direction of Engineer-in-charge |
| 15 | Providing plinth protection 50mm thick cement concrete 1:3:6(1cement:3asand:6graded stone agg., 20mm nominal size) including finishing the top surface concrete smooth within all leads and lifts as per direction of Engineer-in-charge. |
| 16 | Providing tor steel reinforcement for reinforced concrete work including bending, binding, & placing in position complete upto floor two level) within all leads and lifts as per direction of Engineer-in-charge. |
| 17 | Applying priming coat over new steel & other metal surfaces after & including preparing the surface by thoroughly cleaning oil grease dirt and other foreign matter and scoured with wire brushes fine steel wool scrapers and sand paper complete with ready mixed priming paint brushing red lead red-oxide zink oxide chrome complete in all respect within all leads and lifts as per direction of Engineer-in-charge. |
| 18 | Painting two coats(excluding priming coat) on new steel and other metal surface under coat with ready mixed paint brushing to give an even shade including cleaning of all dirt, dust & other foreign matter sand papering and stopping with ready mixed paint other than white within all leads and lifts as per direction of Engineer-in-charge. |
| 19 | White washing with lime on undecorated walls surface (two coats) to give an even shade including thoroughly brooming the surface dirt dust mortar dirt and other foreign matteri n all leads and lifts.as per direction of Engineer-in-charge |
| 20 | Hirmachi colour wash on undecoraed wall surfaces (two coats) to give an even shade includint thoroughly bromming the surface to remove all dirt, dust mortar drops and other foreign matter complete in all respect within all leads and lifts as per direction of Engineer-in-charge. |
| 21 | Providing and fixing MS fan clamps type-I of 16mm dia MS barbent to shape with hooked ends in RCC slab during laying including painting the exposed position of loop, all as per standard design complete within all leads and lifts as per direction of Engineer-in-charge. |
| 22 | Providing 40x3mm flat iron hold fast 40cm long including fixing to frame with 10mm dial meters bolts and nuts and wooden plug and embeding in cement mortar block 30x10x15cm (1:3:6(1cement:3sand:6 graded stone aggregate 20mm nominal size.in all leads and lifts.as per direction of Engineer-in-charge |
| 23 | Providing and fixing following anodized aluminium fittings of anodized transparent and shade with necessary screw etc.complete in all leads and lifts.as per direction of Engineer-in-charge |
| 24 | Sliding door bolts 250x16mm. |
| 25 | M.S. tower bolts (Barrel type) leads and lifts. 200x10mm. |
| 26 | M.S. tower bolts (Barrel type) leads and lifts. 150x10mm. |
| 27 | M.S. tower bolts (Barrel type) leads and lifts. 100x10mm. |
| 28 | M.S. handles 100mm dia |
| 29 | M.S. handles 75mm dia |
| 30 | Providing and fixing of M.S. grills of required patterns in wooden frames of windows etc with MS flat square of round bars with rammed headed bolts & nuts or by screws(Plain grill) within all leads and lifts as per direction of Engineer-in-charge. |
| 31 | Stone/Boulder filling under floors/behind retaining walls.in all leads and lifts.as per direction of Engineer-in-charge Please Enable Macros to View BoQ information |
