|
| 1 | Labour only for attending day to day external water supply complaints of all nature i.e leakage in water supply pipe lines, fitting/fixture, over flow of overhead tank, no water supply,taking out water from trenches during repair including noting the complaints in complaint register complete all as directed by Engineer-in-charge. (Any material required for attending complaints shall be measured and paid separately under respective item herein after) |
| 2 | Labour only for attending day to day electric supply complaints of day to day mantenance of existing LT Panels involving replacement of meterials including connecting electrical accessories / spares of water supply installation from 0830 hrs to 1730 hrs and electrical fitting & light, short circuits in pump house including nothing the complaints from Nodal Point No. I and allied areas in complaints register and distribution to the trademen complete all as directed (any meterial required for atteding complaints shall be measured & paid seperately under respective item here after)Note:- The suitable shift duites as deems fit shall be decision of the Engr-in-charge |
| 3 | Notes for Item No 1.01 & 1.02 :-(i) The complaints shall be attended and the defects shall be rectified by a team of expert and experienced electrician/plumber as applicable assisted with adequate No of helpers complete all as specified and as directed.(ii) The complaints shall be attended and defect shall be rectified within 08 hrs commencing from date and time of notifying the complaint failing which a penalty @ Rs 500/- per complaint per day (08 hrs) shall be levied upon/imposed on the contractor and recovery shall be made from contractor's dues.Contractor rep shall be available wef 0800 hrs to 2000 Hrs to receive and notify the complained (iii) In case, after checking and attending the defect, it is not possible to rectify the defects within 08 hrs the facts shall be brought to the notice of Engineer-in -charge by the contractor /his rep . If Engineer -in-charge is satisfied with contractors view, no recovery will be made.(iv) While attending the complaint of water supply /Electric supply if earth work is required then the same shall be measured and paid seperately under appropriate item of Sch 'A' . However no extra payments shall be made for dewatering.(v) Cutting of GI pipe in position and threading is also deemed to be included in the job rate (Fitting and fixtures will be measured and paid separetely under respective item of Sch A.(vi) All T & P as well as dewatering motor single phase of 3HP with including 100 mtr cable, required for attending the complaints shall be provided by the contracor. (vii) The pipe fitter shall always be in possession of die set complete with cutters , boring Tups , Pipe wrench, Chain wrench,Caulking tools, set of spanners and ladders,wehicle/Ricksha etc Complete,all as required at site. |
| 4 | (viii) The elecrician shall always be in possession of all Electrician tools , LT Megger, Earth tester , Multimeter , Crimping tool, insulation tape, Hand gloves etc complete all as required at site and directed by Engr-in-charge.(ix) All material reqd at site for day to day maintenance shall be issued by Deptt under respective items here in after. |
| 5 | Supply and fixing of GI Socket, medium grade, ISI Marked complete all as specified and as directed of following sizes. |
| 6 | GI Socket 15 mm bore |
| 7 | GI Socket 20 mm bore |
| 8 | GI Socket 25 mm bore |
| 9 | GI Socket 40 mm bore |
| 10 | GI Socket 50 mm bore |
| 11 | Supply fixing of GI Elbow, medium grade, ISI Marked complete all as specified and as directed of following sizes. |
| 12 | GI Elbow 15 mm bore |
| 13 | GI Elbow 20 mm bore |
| 14 | GI Elbow 25 mm bore |
| 15 | GI Elbow 40 mm bore |
| 16 | GI Elbow 50 mm bore |
| 17 | Supply fixing of GI Union, medium grade, ISI Marked complete all as specified and as directed of following sizes. |
| 18 | GI Union 15 mm bore |
| 19 | GI Union 20 mm bore |
| 20 | GI Union 25 mm bore |
| 21 | GI Union 40 mm bore |
| 22 | GI Union 50 mm bore |
| 23 | Supply fixing of GI Nipple, medium grade, 50 to 150 mm long, ISI Marked complete all as specified and as directed of following sizes. |
| 24 | GI Nipple 15 mm bore |
| 25 | GI Nipple 20 mm bore |
| 26 | GI Nipple 25 mm bore |
| 27 | GI Nipple 40 mm bore |
| 28 | GI Nipple 50 mm bore |
| 29 | Supply fixing of GI reducing socket, medium grade, ISI Marked complete all as specified and as directed of following sizes. |
| 30 | GI reducing socket size 20 x15 mm bore |
| 31 | GI reducing socket size 25 x15 mm bore |
| 32 | GI reducing socket size 25 x20 mm bore |
| 33 | GI reducing socket size 50 x40 mm bore |
| 34 | Supply fixing of GI Tee, Medium Grade, complete all as specified and as directed of following sizes |
| 35 | GI Tee , 20 x 20 x 15 mm bore |
| 36 | GI Tee , 20 x 20 x 20 mm bore |
| 37 | GI Tee , 25 x 25 x 20 mm bore |
| 38 | GI Tee , 25 x 25 x 25 mm bore |
| 39 | GI Tee , 40 x 40 x 15 mm bore |
| 40 | GI Tee , 40 x 40 x 20 mm bore |
| 41 | GI Tee , 40 x 40 x 25 mm bore |
| 42 | GI Tee , 40 x 40 x 40 mm bore |
| 43 | GI Tee , 50 x 50 x 15 mm bore |
| 44 | GI Tee , 50 x 50 x 20 mm bore |
| 45 | GI Tee , 50 x 50 x 25 mm bore |
| 46 | GI Tee , 50 x 50 x 40 mm bore |
| 47 | GI Tee , 50 x 50 x 50 mm bore |
| 48 | Supply fixing of GI plug, solid, heavy duty, complete all as specified and as directed of following sizes. |
| 49 | GI plug, 15 mm bore |
| 50 | GI plug, 20 mm bore |
| 51 | GI plug, 25 mm bore |
| 52 | GI plug, 40 mm bore |
| 53 | GI plug, 50 mm bore |
| 54 | Supply fixing of PVC 'L' type holder, suitable for aluminium rod, float ball, of following size bore complete all as specified and as directed. |
| 55 | 15 mm bore |
| 56 | 20 mm bore |
| 57 | 25 mm bore |
| 58 | 40 mm bore |
| 59 | 50 mm bore |
| 60 | Supply fixing of PTMT float valve, Sizes as under, with epoxy coated aluminium rod and high density plastic ball complete all as specified and as directed. |
| 61 | PTMT float valve, 15 mm bore |
| 62 | PTMT float valve, 20 mm bore |
| 63 | PTMT float valve, 25 mm bore |
| 64 | PTMT float valve, 40 mm bore |
| 65 | PTMT float valve, 50 mm bore |
| 66 | Taking up or down GI steel tubing of following sizes with connections from Trenches/floors/walls including cleaning for refixing or removal complete all as specified and as directed.Note :- Excavation & earth work shall be measured & paid separetely. |
| 67 | 15 mm bore |
| 68 | 20 mm bore |
| 69 | 25 mm bore |
| 70 | 40 mm bore |
| 71 | 50 mm bore |
| 72 | Refixing old steel tubing and connections in new or old position(wall/ ceiling/ floor) of following sizes complete all as specified and as directed.Note :- Excavation for new location shall be measured & paid separetely. |
| 73 | GI steel tubing, 15 mm bore |
| 74 | GI steel tubing, 20 mm bore |
| 75 | GI steel tubing, 25 mm bore |
| 76 | GI steel tubing, 40 mm bore |
| 77 | GI steel tubing, 50 mm bore |
| 78 | Laying and Testing of GI steel tubing medium grade of following size in old or new position as in ceiling/walls/Floors with necessary fixing arrangements and including providing new GI fittings complete all as specified and as directed.Note :- (i) Excavation & earth work for new locations shall be measured & paid separetely.(ii) GI steel tubing shall be issud under Sch 'B' as free for laying/fixing only. (iii) GI fittings should be measured and paid under respective items. |
| 79 | GI steel tubing, 15 mm bore |
| 80 | GI steel tubing, 20 mm bore |
| 81 | GI steel tubing, 25 mm bore |
| 82 | GI steel tubing, 40 mm bore |
| 83 | GI steel tubing, 50 mm bore |
| 84 | Supply and Fixing Gun metal gate valve, with iron wheel head screwed both ends for iron pipe as per IS-778 and fixed including taking out unserviceable one, complete all as specified and as directed of following sizes. |
| 85 | Gun metal gate valve, 15 mm bore |
| 86 | Gun metal gate valve, 20 mm bore |
| 87 | Gun metal gate valve, 25 mm bore |
| 88 | Gun metal gate valve, 40 mm bore |
| 89 | Gun metal gate valve, 50 mm bore |
| 90 | Cutting and screwing the existing steel tubing of following size bore for addition & alteration or lengthening screw on pipe to form connector complete all as specified and as directed. |
| 91 | 15 mm bore |
| 92 | 20 mm bore |
| 93 | 25 mm bore |
| 94 | 40 mm bore |
| 95 | 50 mm bore |
| 96 | M&L for Disconnection electrical and water connection of the 12.5 HP centrifugal pump and motor with base plate and transported to work shop opening carefully and replacement of bushes, gland packing, ball bearing, rubber gasket nut and bolt fixing the require new parts(parts such as shaft, impellor, coupling & bearing shall be supplied under relevant item of schedule ) and complete re-fixing its in original position and making out all electrical and water connection and testing complete all as specified and as directed by the Engineer-in-Charge. Note :- Rate includes transportation of motor from the place of installation for repairing and reinstalling the same on existing foundation & testing & commisioning. |
| 97 | Supply and fixing shaft suitable for centrifugal pumps |
| 98 | Supply and fixing GM impeller suitable for centrifugal pumps |
| 99 | Supply and fixing MS coupling suitable for centrifugal pumps |
| 100 | Supply and fixing bearing suitable for centrifugal pumps |
| 101 | Supply and fixing Switch Piano flush type 6 amps single pole one way 240 volts complete all as specified and as directed. |
| 102 | Supply and fixing Switch Piano flush type 16 amps, single pole, one way, 240 volts complete all as specified and as directed. |
| 103 | Supply and fixing Switch Socket outlet 2 in 1, 3 pin, 6 amps 240 volts complete all as specified and as directed. |
| 104 | Supply and fixing Switch Socket outlet 2 in 1, 3 pin, 6 and 16 amps 240 volts complete all as specified and as directed. |
| 105 | Supply and fixing Switch Socket combination 2 in 1, 3 pin, 6 amps 240 volts complete all as specified and as directed. |
| 106 | Supply and fixing Switch Socket combination 2 in 1, 3/5 pin, 6 and 16 amps 240 volts complete all as specified and as directed. |
| 107 | Supply and fixing MCB SP, 6 to 32 Amp, 240 volts complete all as specified and as directed. |
| 108 | Supply and fixing LED batten arrow for multi application suitable for 18 Watts with & including necessary cable connection to make it functional complete all as specified and as directed. |
| 109 | Supply and fixing non metallic PVC conduit 25 mm bore, medium grade having 2 mm wall thickness with & including all fittings such as tee,bends, reducer, elbow, bell mouth, tube ends etc with all other fixing accessories such as couplers, locknuts saddles ,pipe hooks, clips etc complete all as specified and as directed. |
| 110 | Supply and fixing PVC multistranded aluminium conductor, 1100 volts grade , cross sectional area 4 sqmm, 2 core fixed on panels/walls complete all as specified and as directed. |
| 111 | M&L for rewinding of electrical motor 12.5 HP with super enameled copper winding wire of suitable size not less than original after cutting and taking out old winding complete with all insulation material such as Colton top varnish etc of centrifugal pump set motor complete all as specified and as directed by the Engineer-in-Charge. |
| 112 | Supply and fixing lead pig for joints complete all as specified and as directed. |
| 113 | Supply and fixing Spurn Yarn complete all as specified and as directed. |
| 114 | M&L for CI/ DI Pipe fittings such as Tees, bends ,any type, radius and angle/tapers any type, collars,tail pieces,caps and plugs up to 150 mm bore conforming to IS: 1538-1993 complete all as specified and as directed. |
| 115 | M&L for CI/ DI Pipe fittings such as Tees, bends ,any type, radius and angle/tapers any type, collars,tail pieces,caps and plugs 200 to 300 mm bore conforming to IS: 1538-1993 complete all as specified and as directed. |
| 116 | Supply only 15 mm bore Bib tap of PTMT, any tint, high pressure screwed for male/ female threaded, for pipe of size 15 mm bore complete all as specified and as directed. |
| 117 | supply and fixing PPR Gate valve(Brass inserted), ISI Marked of following size, Complete all as specified and as directed. |
| 118 | 20 mm Bore |
| 119 | 40 mm Bore |
| 120 | 50 mm Bore |
| 121 | supply and fixing in replacement PPR male threaded adopter, ISI marked of following size, Complete all as specified and as directed. |
| 122 | 20 mm Bore |
| 123 | 40 mm Bore |
| 124 | 50 mm Bore |
| 125 | Excavation in trenches not exc 1.5 M wide and not exc 1.5 M in depth for pipe line, etc in soft/ loose soil getting out and levelling of bottom surface to required level all as specified and as directed. |
| 126 | Returning filling in, including spreading, leveling, watering and well ramming in layers not exc 25 cm thick complete all as specified and as directed. |
| 127 | Removing excavated material to a distance not exc 50 m and depositing where directed not exc 1.5 meters above the starting point complete all as specified and as directed. |
| 128 | Supply and fixing in replacement of MCCB 3 pole 100 Amps 25 KA complete all as specified and directed. |
| 129 | Supply and fixing in replacement of MCCB 3 pole 63 Amps 25 KA complete all as specified and directed. |
| 130 | Supply and fixing Single headed Gun Metal fire hydrant landing valve type A (single head outlet) of 80mm dia landing valve with 63mm dia female outlet complete and 80mm inlet with rubber blank cap and chain as per IS 5290-1983, suitable for brigade hose of 63mm with couplings conforming to IS 903 including taking down the existing one complete all as specified and directed. |
| 131 | Supply and fixing of weather proof standard fire hose box made of 16 SWG gauge MS Sheet 750mm x 600mm x 250mm with double door with 4mm thick glasses and door frame including locking arrangement by allen key, stove enamelled fire red finish with 'Fire hose' marked on front and brilliant white inside yard, suitable for housing of 2 lengths RRL hose pipe conforming to IS:636-1979 (type-II) of 63mm dia. GM instataneous male and female coupling (IS:903) and branch pipe and nozzel 12.5mm dia including taking down the existing one complete all as specified and directed . |
| 132 | Supply and fixing in position 63mm nominal bore and 15 mtr long synthetic fibre, circular woven jacketed, rubberized fabric reinforced rubber lined (RRL) fire hose pipe of approved make bearing IS : 636-1988 type A mark and having TAC and MMD approval with a pair of 63 x 63 mm gun metal instantaneous type, heavy duty delivery hose coupling (conforming to IS : 903) bound and riveted to the hose pipe with copper rivets and copper wire, complete all as specified and including taking down the existing one complete all as specified and directed . |
| 133 | Supply and fixing in position Gun Metal 63mm dia short size branch pipes with 20 mm dia nozzles with 63mm instantaneous coupling ISI marked (IS: 903). and including taking down the existing one complete all as specified and directed. |
| 134 | Supply, fixing, testing and commissioning of wall mounting swinging type First aid fire hose reel with drum, hanging bracket,Thermoplastic rubber (first aid hose) as per IS 12585 20 mm dia 30 mtr length to with stand 10 kg per Sq cm working pressure fitted with gunmetal nozzle and shut off valve of any size complete all as specified. The hose reel shall be conforming to IS 884-1985 including for 25 mm dia MS pipe connection from riser to hose reel sockets,nipples,elbows,valve etc. Drum shall be fixed on adjoining wall through anchor fasteners/cement concrete hook or MS stand as per site requirement and the rate for fixing/hanging items in the rates quoted(for internal hydrant and one each an either side of stage) including taking down the existing one complete and depositing to MES store yard all as specified and directed . |
| 135 | Supply and fixing water delivery Thermoplastic rubber (first aid hose) as per IS 12585 20 mm dia 30 mtr length to with stand 10 kg per Sq cm working pressure fitted with gunmetal nozzle and shut off valve of any size complete and depositing to MES store yard all as specified and directed. |
| 136 | Supplying & fixing Co2 type 4.5 kgs capacity Fire Extinguisher, assembled from brand new Explosives approved cylinders, complete with screw-down type valve, internal discharge tube, one metre high pressure rayon braided hose, discharge, horn, Bearing ISI Mark IS: 2878. Co2 Cylinder as per IS: 7285 CCE approved ‘ISI’ Valve as per IS: 3224. Co2 Gas as per IS: 15222. internal discharge tube IS: 738. Discharge duration, 10-18 secs. Filled weight of extinguisher, 17 kgs. Tested to 250 kgf/cm2 complete all as specified and as directed . |
| 137 | Supplying & fixing ABC type Stored Pressure 6 kgs capacity Fire Extinguisher, fabricated from MS sheets, fitted with brass forged squeeze grip valve assembly incorporated with pressure gauge, initial charge of 5 kgs. ABC Powder(MAP 50%) and pressurized with nitrogen gas. M.S. Body as per IS : 513 Forged Brass valve as per IS: 6912. Bearing ISI Mark IS: 13849 complete all as specified and as directed . |
| 138 | Supply, fixing, testing and commissioning of 150 dia mm pipe heavy duty class \\"c\\" MS pipe ,ISI marked as per IS: 1239 with all necessary fittings & fabrication like tees, elbows, flanges, reducers, gaskets, nuts and bolts etc welding or screwed joints as required including fixing of pipe with necessary standard clamps structural steel supports as required/directed at site including painting of two coats of synthetic enamel paint of post office red colour over a coat of red oxide primer including taking down the existing one complete all as specified and directed . |
| 139 | All as per Srl item No. 52 here-in-before but size 100 MM. |
| 140 | All as per Srl item No. 52 here-in-before but size 80 MM. |
| 141 | Supply, fixing, jointing & testing cast Iron Sluice Valve of size 80 mm dia ISI Marked, flanged ends drilled pressure rating PN-1.0, PD Short body, Confirming to IS 14846 -2000, having stainless steel spindle with cast iron operation wheel at top including taking out unserviceable sluice valve complete all as specified and as directed . |
| 142 | All as per Srl item No. 55 here-in-before but size 100 MM. |
| 143 | All as per Srl item No. 55 here-in-before but size 150 MM. |
| 144 | All as per Srl item No. 55 here-in-before but size 200 MM. |
| 145 | Supply, fixing, jointing and testing of Cast iron Non Return valve of size 80 mm dia without by pass arrangement , Swing type, confirming to IS 5312, flanged ends pressure rating PN 1.0 complete including taking out unserviceable NRV complete all as specified and as directed . Note:- Flanged joints complete with jointing material shall deemed to be included in the unit rate of this item. |
| 146 | Supply, fixing, jointing and testing of Cast iron Non Return valve of size 100 mm dia without by pass arrangement , Swing type, confirming to IS 5312, flanged ends pressure rating PN 1.0 complete including taking out unserviceable NRV complete all as specified and as directed . Note:- Flanged joints complete with jointing material shall deemed to be included in the unit rate of this item. |
| 147 | Supply, fixing, jointing and testing of Cast Iron Butterfly Valve of size 80 mm dia ISI marked class (PN 1.0) including taking out unserviceable Butterfly valve complete all as specified and as directed . Note:- Flanged joints complete with jointing material shall deemed to be included in the unit rate of this item. |
| 148 | Supply, fixing, jointing and testing of Cast Iron Butterfly Valve of size 100 mm dia ISI marked class (PN 1.0) including taking out unserviceable Butterfly valve complete all as specified and as directed . Note:- Flanged joints complete with jointing material shall deemed to be included in the unit rate of this item. |
| 149 | Supply, fixing, jointing and testing of Cast Iron Butterfly Valve of size 150 mm dia ISI marked class (PN 1.0) including taking out unserviceable Butterfly valve complete all as specified and as directed. Note:- Flanged joints complete with jointing material shall deemed to be included in the unit rate of this item. |
| 150 | Supply, fixing, jointing and testing of Cast Iron Slim seal dual plate wafer type check valve of size 100 mm dia ISI marked class (PN 1.0) including cutting the existing pipe ,complete all as specified and as directed. Note:- Flanged joints complete with jointing material shall deemed to be included in the unit rate of this item. |
| 151 | Supply, fixing, jointing and testing of Cast Iron Slim seal dual plate wafer type check valve of size 150 mm dia ISI marked class (PN 1.0) including cutting the existing pipe ,complete all as specified and as directed . Note:- Flanged joints complete with jointing material shall deemed to be included in the unit rate of this item. |
| 152 | Supply, fixing, jointing and testing in replacement of Bourdon type pressure gauge with gun metal isolation cock and copper ‘U’ Tube.having calibration of 0-10 Kg/cm2 ,and 100 mm dial size all as specified including taking out unserviceable pressure gauge complete all as specified and as directed . |
| 153 | Supply, fixing, jointing and testing in replacement of Pressure switches IPS 100 or approved equivalent) including making connections with the control panel and the pressure vessel complete in all respects.The electrical continuity is maintained between contacts NC& COM under normal conditions. The contacts changeover to NO & COM on rise of pressure to preset value all as specified including taking out unserviceable pressure switch complete all as specified and as directed. |
| 154 | Supply, fixing, jointing and testing in replacement of Gun metal Air release valve of size 25mm dia having rubber ball ( of suitable range and calibrated) complete screwed both ends for iron pipe, ISI Marked, as per IS: 778 of following sizes including taking out unserviceable air release valve complete all as specified and as directed. |
| 155 | Disconnecting & taking out unserviceable Gun metal 3 way Fire brigade inlet to down commer line dismantling and opening carefully for servicing over hauling shifted to and fro to workshop,material and labour for replacement of unserviceable &worm out GM Parts and rubber packing BNW etc complete and refixing same in position and testing all as specified and as directed . Please Enable Macros to View BoQ information |
| 156 | Disconnecting & taking out unserviceable Gun metal 3 way Fire brigade inlet to down commer line dismantling and opening carefully for servicing over hauling shifted to and fro to workshop,material and labour for replacement of unserviceable &worm out GM Parts and rubber packing BNW etc complete and refixing same in position and testing all as specified and as directed . Please Enable Macros to View BoQ information |
