|
| 1 | Supply of submersible pumping set of (KSB/Kalama/Kirloskar/Johnston/Cromption/BS) make conforming to BIS; 8034-1976 latest suitable for lifting clear water (latest with uptodate ammendments) fitted with bronze impellers/suitable alloy directly coupled to squirrell case electric induction motor of same make as (manufacurer standard) conforming to BIS; 9283-1979 (latest with uptodate ammendments) and totally water proof for submersible duty, isolated from the pump by intermediate casing with double mechanical seal in oil chamber, grease packed lubricated bearings & provided with stainless steel thrust bearing plate to with stand vertical loads with minimum wear & tear. It should also be fitted with a device to take up expansion of water with the heating of motor including water level guard,errection clamps,cable clips & depth gauge etc. The pump shall be suitable for operation on data given below:- |
| 2 | Total Head :- 120.00 mtr |
| 3 | Discharge required from each pump :- 6.00 LPS |
| 4 | Providing and fixing automatic starter reputed make including auto start,auto stop and restart facility single phase preventer ,3 phases indicator,timer,relay,selector switch,auto and manually start stop facility,prevention of phase reversal,imbalance and overload and fixed with compatible starter in sheet enclosure with cabling complete in all respect to deliver results. |
| 5 | T/well Ludhiar 30 HP |
| 6 | T/well Lubh 50 HP |
| 7 | Erection and Lowering of Pumping Machinery (Motor and Pump) and column assembly including cost of hiring of Chain Pulley of required capacity, Tripod Stand and Labour complete as per entire satisfaction of Engineer in charge. |
| 8 | Repair/Rewinding of Submersible Motor complete for smooth running of pump/motor having (Required Discharge & Minimum 6 month Guarantee Period) complete in all respect i/e replacement of necessary required matarial such as rotor sleeve, new housing, bush, thrust plate, terminal plate, thurst bearing new water seal, new pump shaft, new impeller, repair of impaller, pump body, bowl housing, bush pump bearing (SKF make) as per size necessary etc complete as per entire satisfaction of Engineer in charge. |
| 9 | Carriage of Pumping Machinery (Motor and Pump) from Pump House to work shop and Back to Pump house after repair complete within all leads and lifts. |
| 10 | P/F Nut and Bolt of required size complete within all leads and lifts as per entire satisfaction of Engineer in charge. |
| 11 | P/F Rubber Sheet (Champion Make) of required size complete within all leads and lifts as per entire satisfaction of Engineer in charge. |
| 12 | Providing and Supplying of Transformat Oil complete in all respect. |
| 13 | Providing and fixing ball bearing 6309 SKF complete within all respect as per entire satisfaction of Engineer in charge. |
| 14 | Providing and fixing ball bearing 6310 SKF complete within all respect as per entire satisfaction of Engineer in charge. |
| 15 | Providing and fixing ball bearing 6313 SKF complete within all respect as per entire satisfaction of Engineer in charge. |
| 16 | Providing and fixing ball bearing 6314 SKF complete within all respect as per entire satisfaction of Engineer in charge. |
| 17 | Providing and fixing PVC jointless flat water proof copper cable of finolex/Gloster as per BIS-1554 Part-I-1998 latest with upto date ammendments suitable for the pump sets offered i/c all other electrrical equipment/accessories such as thimbles flexible pipe solder nuts bolts cable, gland etc laid in pipe for trenches under floor. The type & size will be subject to approval of HPSEB authority in case of non acceptance by HPSEB authorities it shall have to be replaced by the tenderer without extra cost ) as per the entire satisfaction of the Engineer In charge. |
| 18 | 3 core Cable 16mm Square |
| 19 | 3 core Cable 10mm Square |
| 20 | 3 core Cable 6mm Square |
| 21 | Excavation in foundation and trenches etc. (in pipes and pits) in all kinds of soils such as pick work, jumper work, blasting in soft/hard rock, chiselling/wedging out of rock/where blasting prohibited) saturated soil stacking the excavated soil as directed by the Engineer-in-charge clear from the edge of excavation and then returning the stacked soil in 15cm layers when required into plinth sides of foundation etc. consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed by the Engineer -in-charge in all leads and lifts. |
| 22 | Dismentaling of GI pipe of various dia in trenches complete in all respect (earth work to be measured and paid for separately) including cutting of pipe complete in all leads and lifts as per the direction & satisfaction of E-in-charge. |
| 23 | 100mm dia |
| 24 | 80mm dia |
| 25 | 65mm dia |
| 26 | 50mm dia |
| 27 | 40mm dia |
| 28 | 32mm dia |
| 29 | Re-Laying, jointing and testing of old dismentaled pipe in trenches GI pipe of various dia confirming to ISI specification i/c commission complete in all respect (earth work in trenches shall be measured and paid for separately) within leads and lifts as per the direction & satisfaction of Engineer-in-charge. |
| 30 | 100mm dia |
| 31 | 80mm dia |
| 32 | 65mm dia |
| 33 | 50mm dia |
| 34 | 40mm dia |
| 35 | 32mm dia |
| 36 | Providing Laying ,Jointing and testing in trenches Galvanised Mild Steel tube (L) of following dia including tube fitting complete in all respects with in all lead and lifts as per direction & satisfaction of Engineer - in - charge (earth work in trenches is to be measured and paid for separately). |
| 37 | 100mm dia |
| 38 | 80mm dia |
| 39 | 65mm dia |
| 40 | 50mm dia |
| 41 | 40mm dia |
| 42 | 32mm dia |
| 43 | Providing and fixing G.I. Union of various dia complete in all respects with in all lead and lifts as per direction & satisfaction of Engineer - in - charge. |
| 44 | 100mm dia |
| 45 | 80mm dia |
| 46 | 65mm dia |
| 47 | 50mm dia |
| 48 | 40mm dia |
| 49 | 32mm dia Please Enable Macros to View BoQ information |
