|
| 1 | Supply and Erection of 06 Mtr Galvanized Iron pole with galvanizing done in single dipping. (Average coating. thickness Minimum 65 Microns) continuously tapered poles having Octagonal / circular cross section designed to withstand the maximum wind speed as per Is 875, The pole shaft shall he made from sheeth steel (47 Steel Conforming to grade 536510) and Confirming to BS&N 1002, and shall be continuously tapered with single longitudinal welding. There shall not be any circumferential welding. The welding of pole shaft shall be done by Submerged Arc Welding (SAW) process. pole shafts shall be provided with tha rigid flange plate of suitable thickness (Fe 410 conforming to IS 226 / IS 2062) with provision for fixing.Technical Specification:- 1) No. Of Section 1 NO. 2) No of sides 8 NOS. 3) Base plate size 225 X 225 MM4) Base plate thickness 12 MM 5) Base plate hole PCD 225 MM 6) No of holes 4 NOS. 7) Hole dia 24 MM / SLOTTED 8) Size of door opening 250 MM 9) Pole section length 6000 MM 10) Pole section Theckness 3 MM 11) Bottom Dia ( Outer ) 130 MM 12) Top Dia ( Outer ) 70 MM 13) Foundation Bolt Length 550 MM 14) Foundation Bolt Dia 20 MM 15) Wind Speed 180 Km / Hr 16) Dimension Tolerance As Per BSEN 4017) Material Tolerance As Per IS 1852 - 1985 18) Shaft Material Type As Per BSEN 10025 S 355 Or Equivalent 19) Base Plate Type As Per IS 2062 20) Foundation Bolt Type As Per IS 1367 Gr. 6.821) Material Protection Hot Dip Galvanized 22) Zinc Coating Thickness 65 Microns 23) Galvanizing Type AS PER ISO 1461 : 1999 24) Finishing Type As Per IS 11759 - 198. The octagonal Poles shall have lockable door of approximate 500 mm length at the elevation of 500 mm from the Base plate with bakelite sheet having 6A SP MCB and 16 Sq.mm stud type connector (4 nos) inside the pole at door opening for cable connection (Utkarsh/Valmont/BPP/Surya Make. Also includes Supply/Fixing of 8 SWG G.I wire run over the cable length properly earthed with main earthing pit/grid (Standard make) |
| 2 | Providing and laying of M15(1:2:4) Cement Concrete pole block of size ( 2ʹ x 2ʹ x 4ʹ)having 3ʹ U/G & 1ʹ A/G including cost ofform work,Curing,Finishing & Base Mesh Reniforcement having 12mm dia main as well as temperature (spacing 6 inch C/C)The job includes all charges(Complete Job) with Following Procedure & All as per pre approved by Engineer in charge:-A) Excavation of Pit for Foundation Size upto required depth from Ground levelB) Dressing of Pit and Dry stone pitching 200 mm thick including supply of stones and preparing surface complete.C) Providing and laying in position cement concrete of M-10 grade of 75 mm thicknessD) Reinforcement for R.C.C. work with MT bars including straightening, cutting, bending, placing in position and binding all complete.E) Centring and shuttering including strutting, propping etc. and removal of form work for Footing and PedestalF) Providing & Fixing of 2 no. Required Size PLB HDPE Pipe & Foundation Bolt with template as per OEM Recommendations.G) Providing and Laying Reinforce cement Concrete of M-25 grade In footing and Pedestal including Curing the foundation for 7 days. |
| 3 | Supply, Installation, Testing and Commissioning of Hybrid All-In-Two Solar Powered LED Street Light, the luminaire housing shall be made of die-cast aluminum and the solar sub-system housing shall be made of extruded aluminium with corrosion resistant finish. The system shall be of All-In-Two construction with independent solar sub-system allowing flexible photovoltaic orientation for maximum solar energy collection. The luminaire shall be minimum IP66 rated and IK10 impact resistant, while the solar sub-system shall be minimum IP54 rated. The fixture shall be pole mounted and suitable for road and area lighting applications. The solar sub-system shall include a pre-tilted mounting bracket to maximize solar exposure. The fixture shall include an in-built high-performance LED luminaire integrated with a solar power system. The solar sub-system shall consist of a high-efficiency monocrystalline photovoltaic panel, Solar PV panel size 150Wp and panel voltage 18V, deep cycle Lithium Ferro Phosphate (LiFePO4) battery, integrated MPPT charge controller System wattage options shall be 55W with a system efficacy of 165 lm/W. Charge controller efficiency shall be ≥97% (charging) and ≥96% (discharging). Inbuilt surge protection shall be minimum 10kV (Hybrid version). Protection shall include battery reverse polarity, panel reverse polarity, battery over voltage, panel over voltage, reverse current into PV, load short circuit, over temperature protection and 0°C charging protection. The luminaire shall have an in-built high efficiency LED light engine with system lumen output options of 9000 lumens operating at 55W. Lumen Efficacy of 165 lumens/Watt. Correlated Color Temperature shall be 5700K and Color Rendering Index shall be ≥70. Optical distribution shall be suitable for road and area lighting applications with uniform illumination. The luminaire shall operate with automatic dusk-to-dawn ON/OFF sensing. The battery shall be Lithium Ferro Phosphate (LiFePO4) type with minimum 2000 charge cycles at 90% depth of discharge, battery capacity 12.8V 72Ah. Autonomy shall be minimum 2 nights with configured dimming profile and approximately 15 hours at 100% output on fully charged battery without dimming. The dimming profile shall be 3 hours at 100%, 2 hours at 70%, 5 hours at 30% and 2 hours at 100%. The luminaire shall have a declared life of 50,000 burning hours at L70B50. The system shall include indication for battery charging and fault conditions. The luminaire and control gear shall comply with IEC 55015, EN 61547, EN 61000-6-3, IEC 62109-1:2019 and IEC 61000-4-5:2017 standards.Note: The luminaire shall be supplied as a complete integrated solar lighting system including PV panel, battery, MPPT charge controller, mounting brackets and IP67 connectors. All technical parameters shall be subject to approval by the lighting designer / engineer prior to supply. Manufacturer of the fixture should have in-house NABL approved testing Lab with a facility to test , Photometry of the product. (certificates should be provided before supplying or demanding of AOI fixture) The job further includes replacement warranty of fixture (if damaged/burnt out what so ever reason) for a period of two years reckoned from date of successful commissioning /handing over of site to intending department. The fixture should have LM 79 for the fixture, LM 80 for the LED chip, BIS for the battery cell. certificates and same are to be submitted before approving of fixture. Philips/Wipro/Ecolink/Trilux/LT/Endo Make. The agency/contractor has to submit Technical Data Sheet on OEM Letter Head Before supply of material for approval. |
| 4 | Providing of service connection to be carried from pole junction box to luminaries using 3-Core 1.5 Sq.mm FR-LSH multistrend copper wire(Flat Cable) confirming IS 694 ammended upto date of Havells/Polycab/Salzer/BCH Make. |
| 5 | Supply/Laying/Testing and Commissioning of 4-Core 16 mm sq. Al armored XLPE Insulated,PVC cable Havells/Polycab/KEI/Paramount/RR-Kabel Make. Including Supply/Laying of HDPE Pipe of suitable dia ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (01 Ft below ground level) including excavation and refilling the trench of standard make as approved.The cable shall include end termination lugs with its crimping /taping. (Test Certificate shall be provided) |
| 6 | Design,Supply, Installation, Testing and Commissioning of CPRI Approved (IS/IEC:61439) Main LT Control Single Door panel Slopped Roof fabricated of 16 gauge sheet steel,the panel should have standing dust & vermin proof with gasket lockable door of 16 gauge sheet steel. The Panel should be painted with Electro static powder coated colour, Siemens grey structural with proper chemical pre-treatment with film thickness 35-40 Microns,duly fitted with R/Y/B Phase-indicators etc & angle iron 50x50x6mm stand painted in black colour of 2.5 feet height/ground clearance properly grouted in cement concrete of 1:2:4 ratio-filter with baby insulators/glands/thimbles suitable for use at 415 Volts 3 Phase,4 wire 50Hz system complete in all respects complete in all respects with following:-Incoming: 63-100 Amp-4 pole,26-36kA MCCB with extended terminals Adjustable Thermal & Fixed Magnetic L&T/ABB/Legrand/Simens Make.Outgoing: 100 Amp Suitable Al. Bus bar = 01 Set Please Enable Macros to View BoQ information |
