|
| 1 | Clearing Jungle including uprooting rank, vegetation, grass, brush wood, Trees & sapling of girth upto 30cm measured at a height of 1 mtr above ground level and removal of rubbish upto a distance of 50 mtr outside the periphery of the area cleared. (per sqm) |
| 2 | Earth work in bulk excavation by manual means in trenches for foundations drains pipes, cables etc. not exceeding 1.5 mtrs in width and for shafts, wells, cesspits and the like not exceeding the 10 sq. mtr on plan inculding dressing of sites and ramming of bottoms lift upto 1.5, mtrs including getting out excavated earth and disposal of surplus excavated earth as directed. All kinds of soil 1mtr from cutting edge. |
| 3 | Construction of Muthu Bund compressing of 50% boulders & 50% wood bushes including working in wet conditions. |
| 4 | Silt clearance from canals inclusive of initial lead 50 mtr and 1.5 mtr respectively. A. Dry |
| 5 | Silt clearance from canals inclusive of initial lead 50 mtr and 1.5 mtr respectively. A. wet |
| 6 | Slip Clearance i) i) In ordinary soil disposal lead upo 50 mtrs and lift upto 1.5 mtrs |
| 7 | Slip Clearance i) In ordinary soils, mixed with moorum/Kankar/ Shingle/boulders,disposal lead upto 50m and lift 1.5m |
| 8 | Demolishing cement concrete manually / by mechanical means including disposal of material within 50 Mtr lead as per directions of Engineer-in-charge:1:3:6 or richer mix(i/c equivalent design mix) |
| 9 | Demolishing cement concrete manually / by mechanical means including disposal of material within 50 Mtr lead as per directions of Engineer-in-charge:D. 1:4:8 or leaner mix(i/c equivalent design mix) |
| 10 | Dismantling old plaster or skirting, raking out joints and leaning the surface for plaster including disposal of rubbish to the dumping ground with 50 Mtr lead. |
| 11 | Providing and laying in position cement concrete of specified garde including curing but excluding the cost of centring and shuttering all work upto plinth level with 1:4:8 (1 cement 4 coarse fine sand 8 graded stone aggregate 40mm nominal size) |
| 12 | Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centering and shuttering. all work upto plinth level with 1:3:6 (1 cement: 3 coarse sand: 6 graded stone aggregate 20mm nominal size). |
| 13 | Cement concrete flooring 1:2:4(1cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry & curing complete, but excluding the cost of nosing steps etc. complete 40mm thick with 20 mm nominal size stone aggregate. |
| 14 | 12mm cement plaster of mix 1:4(1cement : 4 Coarse sand) |
| 15 | Dumping stones excluding cost of stones in horizontal on level. |
| 16 | Supply of stone boulders(nallah)nominal size 225 mm(Stack measurements reduced by 15%) |
| 17 | Centering and shuttering including strutting propping etc. and removal of form for. Foundations, footings, bases of columns etc for mass concrete. |
| 18 | Centering and shuttering including strutting propping etc. and removal of form for. Walls (any thickness), including attached pilasters, buttresses, plinth and string courses etc. |
| 19 | Centering and shuttering including strutting propping etc. and removal of form for. Suspended floors, roofs, landings, balconies and access platforms. |
| 20 | Providing and laying in position specified grade of reinforced cement concrete including curing but excluding the cost of centering, shuttering, finishing and reinforcement. All work upto plinth level (1:2:4) 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) |
| 21 | Steel reinforcement for RCC work including straightening, cutting, bending, placing in position & binding all complete above plinth level. Cold twisted bars |
| 22 | Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq meters and under, including cutting the patch in proper shape raking out joints & preparing & plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 meters lead.b. Cement mortar 1:4 (1 Cement : 4 Coarse Sand ) |
| 23 | Engagement of extra labour for restoration work(wherever required) . Mazdoor |
| 24 | weed clearance from canal including extraction of roots |
| 25 | Filling empty cement bags with sand /earth including cost of sewing and strings; excluding the cost of bags and earth/sand. |
| 26 | Unloading/ Placing filled EC bags in positionA. Placing in dry |
| 27 | Unloading/ Placing filled EC bags in position B. Placing in water |
| 28 | Supply of stone dust for filling of E.C bags |
| 29 | Supply of E.C bags |
| 30 | Supply of knitted BA wire crates of size 6.00 x1.50x1.50m (6” x 6” mesh) including cost of BA Wire for binding of crates and carriage upto site of work |
| 31 | Providing & fixing PVC pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. a) 75 mm dia |
| 32 | Providing & fixing PVC pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. a) b) 110 mm dia |
| 33 | Dry random rubble masonry without bond stone |
| 34 | Carriage of stones by head load from local nallah to site of work (Extra carriage shall be paid only after verification by the concerned site engineer) AEE. i. 1st 50 mtr |
| 35 | Carriage of stones by head load from local nallah to site of work (Extra carriage shall be paid only after verification by the concerned site engineer) AEE. ii. Beyond 50 mtr |
| 36 | Carriage of Sand by Mechanical transport and Head Load.a) By Mechanical means. i) 1st 20 Km |
| 37 | Carriage of Sand by Mechanical transport and Head Load.a) By Mechanical means. ii) Beyond 20 Km |
| 38 | Carriage of Sand by Mechanical transport and Head Loadb) By Head Loadi) 1st 50 mtr |
| 39 | Carriage of Sand by Mechanical transport and Head Loadb) By Head Load ii) Beyond 50 mtr |
| 40 | Carriage of stone aggregate by Mechanical transport and Head Loada) By Mechanical means i) 1st 20 Km |
| 41 | Carriage of stone aggregate by Mechanical transport and Head Loada) By Mechanical means ii) Beyond 20 Km |
| 42 | Carriage of stone aggregate by Mechanical transport and Head Loada) b) By Head Load i) 1st 50 mtr |
| 43 | Carriage of stone aggregate by Mechanical transport and Head Loada) b) By Head Load ii) Beyond 50 mtr |
| 44 | Disposal of silt/slip by Head Load. a) 1st 50 mtr. |
| 45 | Disposal of silt/slip by Head Load. a) Beyond 50 mtr. |
| 46 | Trap (Sand Cast Iron) 1) 80 mm dia Brass full way valve with C.I Wheel (screwed end). |
| 47 | Trap (Sand Cast Iron) 1) 2) 250 mm dia Sluice valve (With caps) C.I of Class I |
| 48 | Trap (Sand Cast Iron) 3) 300 mm dia sluice valve (with caps) C.I of Class I. |
| 49 | Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. |
| 50 | Finishing walls with water proofing cement paint of required shade:13.117.1 Old work (one or more coats applied @ 2.20 kg/10sqm) over priming coat of primer applied @ 0.80 liters/10sqm complete.including cost of priming coat |
| 51 | Painting with oil type wood preservative of approved brand and manufacture on old work (one or more coats) |
| 52 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to European type W.C. of quality and make as approved by Engineer - in - charge |
| 53 | Anodised Aluminum tower bolt (barrel type) 150 x10 mm |
| 54 | Assistant Fitter or 2nd class Fitter |
| 55 | 15 mm nominal bore G.I. Unions |
| 56 | 20 mm nominal bore G.I. Unions |
| 57 | 15 mm bore for 45 cm long Union |
| 58 | 20 mm nominal bore G.I. Unions |
| 59 | 15 mm dia G.I. Pipes (Medium) |
| 60 | Providing and fixing wash basin with C.I. brackets, 15 mm PTMTpillar cock, 32 mm PTMT waste coupling of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required. White Vitreous China Flat back wash basin size 550x400 mm with single 15 mm PTMT pillar cock |
| 61 | Structural steel work in built up sections, trusses and framed work ,including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. Welded |
| 62 | Providing and fixing 1mm thick M.S. sheet sliding-shutters with frame and diagonals braces of 40x40x6mm angle iron, 3mm M.S. gusset plates at the junction and corners, 25mm dia pulley, 40x40x6mm angle and T-iron guide at the top and bottom respectively including applying a priming coat of approved steel primer |
| 63 | Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100 mm sand cast Iron P or S trap, 10 liter low level white P.V.C. flushing cistern, including flush pipe (of approved make) with manually controlled device (handle lever) conforming to IS: 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. White vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests |
| 64 | Providing and fixing white vitreous china squatting plate urinal withintegral rim longitudinal flush pipe |
| 65 | Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour: Waste coupling 38mm of 83 mm length and 77 mm breadth weighing not less than 60gms |
| 66 | Providing and fixing rectangular high density polyethylene water storage loft tank with cover, conforming to ISI: 12701, colour of opaque white or as approved by Engineer-in-charge. The rate includes making necessary holes for inlet, outlet & over flow pipes. The base support i/c fittings & fixtures for tank shall be paid separately |
| 67 | Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in : Cement mortar 1:4 ( 1 cement : 4 coarse sand) |
| 68 | Providing and fixing 15 mm nominal bore C.P. brass bib cock of approved quality conforming to IS : 8931Providing and fixing 15 mm nominal bore C.P. brass angle valve forbasin mixer and geyser points of approved make conforming to IS : 8931 |
| 69 | Providing and fixing 15 mm nominal bore C.P. brass angle valve forbasin mixer and geyser points of approved make conforming to IS : 8931 |
| 70 | 15 mm PTMT bib cock with flange (fancy) |
| 71 | 15 mm PTMT Pillar Cock |
| 72 | Adjustable Vitreous China Cistern with fittings of flushing capacity 3 litre/ 6 litre 9 adjustibla to 4 litre/8 litre) |
| 73 | Grating (S.C.I.) for gully or Nahni 100 mm dia. |
| 74 | Grating (S.C.I.) for gully or Nahni 15 mm dia G.I. elbows |
| 75 | Providing laying for water pumps 1 HP including fitting. Complete job. (ISI approved brand) |
| 76 | Provision for Electric Fitting.(Complete job) Please Enable Macros to View BoQ information |
