|
| 1 | SITC of Stainless steel 304 grade PICK UP WORK COUNTER with sink and three side covering and two Overhead Shelf with Heating element. |
| 2 | Overall dimension : 1500X700X850 (LXWXH) mmSink size : 450X450X250 mm made up of SS 304 grade with Mixer faucet (make T&S or aluids or equivalent), coupling and waste pipe. Top of table to be made in 16 SWG Stainless steel AISI 304 Grade sheet bent 50mm & 12mm all sides, nicely edge-cut, welded & braised and to be covered on 3 side with same sheet.TOP FRAME made with corner angle frame of 38X38X3mm SS 304 grade and apron should be attached with SS Stiffner of size 12X25X100X25X12.2 Nos. OVER HEAD SHELF of size 1500X300 mm & 50mm high back splash placed at 350mm intervals made of 1.2mm thick SS304 grade sheet bent 25mm & 12mm all sides with HEATING ELEMENT supporting on 25 MM 4 Nos. square pipe.Counter Base Legs made up of 40X40X1.2 MM SS 304 grade PIPE and BULLET TYPE ADUJSTABLE BUSH.ALL MATERIAL AISI SS 304 including sheet, pipe, angle, nut & bolt. Undershelf made of 1.2MM SHEET WITH 12X25X100X25X12 mm undershelf stiffner.Approved make of SS 304 grade sheet of Jindal, Tata, SAIL or equivalent. |
| 3 | SITC of GARBAGE BIN 120 LTR capacity |
| 4 | Overall dimension : 48X55X92CMPRIMARY MATERIAL 100% VIRGIN HIGH DENSITY POLYETHYLENE HDPE, BODY UV STABILIZED POLYETHYLENE WITH SOLID RUBBERIZED WHEEL and paddle operated lid. APPROVED MAKE NILKAMAL/ CAMBRO OR EQUIVLENT |
| 5 | SITC of DISH STORAGE CABINET WITH HOT SLIDING DOOR |
| 6 | Overall dimension : 1500X350X850 (LXWXH) mmTop of table to be made in 16 SWG Stainless steel AISI 304 Grade sheet bent 50mm & 12mm all sides, nicely edge-cut, welded & braised and to be covered on 3 side with same sheet.TOP FRAME made with corner angle frame of 38X38X3mm SS 304 grade and apron should be attached with SS Stiffner of size 12X25X100X25X12.Counter Base Legs made up of 40X40X1.2 MM SS 304 grade PIPE and BULLET TYPE ADUJSTABLE BUSH.ALL MATERIAL AISI SS 304 including sheet, pipe, angle, nut & bolt. 2 nos. Undershelf made of 1.2MM sheet supported on 12X25X100X25X12 mm undershelf stiffner with 2nos. insulated double skin sliding doors of 1.2mm thick SS sheet .Approved make of SS 304 grade sheet of Jindal, Tata, SAIL or equivalent. |
| 7 | SITC of DISH STORAGE CABINET WITH HOT SLIDING DOOR |
| 8 | Overall dimension : 2400X350X850 (LXWXH) mmTop of table to be made in 16 SWG Stainless steel AISI 304 Grade sheet bent 50mm & 12mm all sides, nicely edge-cut, welded & braised and to be covered on 3 side with same sheet.TOP FRAME made with corner angle frame of 38X38X3mm SS 304 grade and apron should be attached with SS Stiffner of size 12X25X100X25X12.Counter Base Legs made up of 40X40X1.2 MM SS 304 grade PIPE and BULLET TYPE ADUJSTABLE BUSH.ALL MATERIAL AISI SS 304 including sheet, pipe, angle, nut & bolt. 2 nos. Undershelf made of 1.2MM sheet supported on 12X25X100X25X12 mm undershelf stiffner with 2nos. insulated double skin sliding doors of 1.2mm thick SS sheet .Approved make of SS 304 grade sheet of Jindal, Tata, SAIL or equivalent. |
| 9 | SITC of PICK UP UNDER COUNTER REFRIGERATOR with overhead shelves |
| 10 | REFRIGERATOR SIZE 1800X750X850mmCapacity - 526 Ltr. (400W)1.6 MM THICKNESS TOP WITHOUT BACK SPLASH,ALL MATERIAL AISI 304 GRADE0.9mm thick SS 304 grade sheet at back and baseSIX REMOVABLE & ADJUSTABLE SHELVESTHREE DOOR 304 INSULTAION DOUBLE SKIN DOORDOOR OPENING 400MM X600MM for placing of BAKING TRAY ,AMBIENT TEMP 43 degree celcius TEMP WITH AIR COOLED OR AUTO DEFROST. REFEGRATION GAS R-134 A with compressor and all necessary accessories complete.DIGITAL READ OUT THERMOMETER, TIME DEALY AUTO START, FORCED DRAFT COOLING, condensing cooling light, defrost indicator, fan running indicator, high low temperature alarm.50 MM PU FOAM ON ALL SIDE2 Nos. OVER HEAD SELF of size 1500X300 mm & 50mm high back splash placed at 350mm intervals made of 1.2mm thick SS304 grade sheet bent 25mm & 12mm all sides with HEATING ELEMENT supporting on 25 MM 4 Nos. square pipe.Counter Base Legs made up of 40X40X1.2 MM SS 304 grade PIPE and BULLET TYPE ADUJSTABLE BUSH.APPROVED MAKE WILLIAMS BLR /HOSHIZAKI OR EQUIVALENT |
| 11 | SITC of PILLAR SPREADER TABLE WITH TWO UNDER SELF |
| 12 | SPERADER TABLE SIZE 600X650X850 mm (LXWXH) with 150mm back splashALL MATERIAL AISI 304 GARDE Top of table to be made in 16 SWG Stainless steel AISI 304 Grade sheet bent 50mm & 12mm all sides, nicely edge-cut, welded & braised and to be covered on 3 side with sheet. Top and UNDER SELF should be SUITABLY JOINT /WELDED to match with the ADJOINING WORK TOP AT SITE. EQUIPMENT TOP PROFILE AS PER LAYOUT PLANTOP FRAME made with corner angle frame of 38X38X3mm SS 304 grade and apron should be attached with SS Stiffner of size 12X25X100X25X12.FOUR (04) NOS 38MM X38MM SQUARE PIPE SS LEGS WITH LEGS ADJUSTABLE BULLET FEET FULL WIDTH 1.2 MM THICK BOTTOM AND MIDDLE SHELFApproved make of SS 304 grade sheet of Jindal, Tata, SAIL or equivalent. |
| 13 | SITC of SPREADER TABLE WITH TWO UNDER SELF |
| 14 | SPERADER TABLE SIZE 450X900X850 mm (LXWXH) with 150mm back splashALL MATERIAL AISI 304 GARDE Top of table to be made in 16 SWG Stainless steel AISI 304 Grade sheet bent 50mm & 12mm all sides, nicely edge-cut, welded & braised and to be covered on 3 side with sheet. Top and UNDER SELF should be SUITABLY JOINT /WELDED to match with the ADJOINING WORK TOP AT SITE. EQUIPMENT TOP PROFILE AS PER LAYOUT PLANTOP FRAME made with corner angle frame of 38X38X3mm SS 304 grade and apron should be attached with SS Stiffner of size 12X25X100X25X12.FOUR (04) NOS 38MM X38MM SQUARE PIPE SS LEGS WITH LEGS ADJUSTABLE BULLET FEET FULL WIDTH 1.2 MM THICK BOTTOM AND MIDDLE SHELFApproved make of SS 304 grade sheet of Jindal, Tata, SAIL or equivalent. |
| 15 | SITC of S.S. CLADDED MOBILE TANDOOR |
| 16 | TANDOOR SIZE 900X900X850 mm (LXWXH) with 150mm back splashALL MATERIAL AISI 304 GARDE 2.00 MM SS TOP WITH CAST IRON RING EXTERIOR 1.2 MM THICK SS CLADDING and INTERIOR 1.2 mmTHICK MS CLADDING and adequate MS section Structure.INNER 40 MM THICK MINERAL WOOL INSULATION123 MM SET BACK in BODY LEGS FOR GAS PIPELINEFRONT SS REMOVABLE OPENING WITH SHUTTER125 MM NON MARKING RUBBERZIED WHEELS WITH LOCKS4 NOs. HANDLE of 8 MM SS BARApproved make of SS 304 grade sheet of Jindal, Tata, SAIL or equivalent. |
| 17 | SITC of CHAPATI PLATE WITH PUFFER |
| 18 | SIZE 1200X900X850mm (LXWXH) with 150mm HIGH REAR SPLASHALL MATERIAL AISI 304 GRADEGAS OPRATEDALL BURNERS ,WALLS,RV,COPPER PIPE TOTAL MATERIAL IS HPC ISI BRAND.15.00 MM THICK MS PLATE TOP with front gutter and SS grease drawer and Puffer plate for chapati 3 Nos. \\"V\\" type H.P. Burner with seperate pilot lampTOP SECURED TO 38MM X38MMX3MM SS WELDED FRAME WORKBUILT IN PRESSUR CONTROLLER REGULTOR1.2MM THICK SS BOTTOM SHELF100 MM REAR LEGS SETBACK FOR GAS PIPE ROUTINGCounter Base Legs made up of 40X40X1.2 MM SS 304 grade PIPE and BULLET TYPE ADUJSTABLE BUSH.Approved make of SS 304 grade sheet of Jindal, Tata, SAIL or equivalent. |
| 19 | SITC of SMOOTH HALF GRIDDLE OR HOT PLATE |
| 20 | SIZE 1200X900X850mm (LXWXH) with 150mm HIGH REAR SPLASHALL MATERIAL AISI 304 GRADEGAS OPRATED15 MM THICK MS TOP with front gutter and SS grease drawer and 1/3rd top area for grilling3 Nos. \\"V\\" type H.P. Burner with seperate pilot lampALL BURNERS ,WALLS,RV,COPPER PIPE TOTAL MATERIAL IS HPC ISI BRANDTOP SECURED TO 38MM X38MMX3MM SS WELDED FRAME WORK Counter Base Legs made up of 40X40X1.2 MM SS 304 grade PIPE and BULLET TYPE ADUJSTABLE BUSHBUILT IN PRESSUR CONNTROLLER REGULTOR1.2MM THICK SS BOTTOM SHELF100 MM REAR LEGS SETBACK FOR GAS PIPE ROUTING. Approved make of SS 304 grade sheet of Jindal, Tata, SAIL or equivalent. |
| 21 | SITC of SMOOTH HOT PLATE |
| 22 | SIZE 1200X900X850mm (LXWXH)with 150mm HIGH REAR SPLASHALL MATERIAL AISI 304 GRADEGAS OPRATED15 MM THICK MS TOP with front gutter and SS grease drawer 3 Nos. \\"V\\" type H.P. Burner with seperate pilot lampALL BURNERS ,WALLS,RV,COPPER PIPE TOTAL MATERIAL IS HPC ISI BRANDTOP SECURED TO 38MM X38MMX3MM SS WELDED FRAME WORK BUILT IN PRESSURE CONTROLLER REGULATOR1.2MM THICK SS BOTTOM SHELF Counter Base Legs made up of 40X40X1.2 MM SS 304 grade PIPE and BULLET TYPE ADUJSTABLE BUSH100 MM REAR LEGS SETBACK FOR GAS PIPE ROUTINGApproved make of SS 304 grade sheet of Jindal, Tata, SAIL or equivalent. |
| 23 | SITC of IDLI STEAMER |
| 24 | Dual Fuel options (Gas + Electric 2KW) for versatility. SIZE : 435X322X925Stainless Steel 2mm THICKNESS 304 grade for durability, rust resistance, and hygieneCapacity: 104 idlis per batch. Trays/Plates: 9 trays measuring 12x12 inches or 14x18 inches.Construction: Heavy-duty, often featuring a vertical, insulated box design with a secure, heat-resistant door and sturdy handles. Approved make of SS 304 grade sheet of Jindal, Tata, SAIL or equivalent. |
| 25 | SITC of WORK TABLE WITH TWO UNDER SELF FOR IDLI STEAMER |
| 26 | WORK TABLE SIZE-750X900X850mm (LXWXH) with 150mm back splashALL MATERIAL AISI 304 GARDE Top of table to be made in 16 SWG Stainless steel AISI 304 Grade sheet bent 50mm & 12mm all sides, nicely edge-cut, welded & braised. Top and UNDER SELF should be SUITABLY JOINT /WELDED to match with the ADJOINING WORK TOP AT SITE. EQUIPMENT TOP PROFILE AS PER LAYOUT PLANTOP FRAME made with corner angle frame of 38X38X3mm SS 304 grade and apron should be attached with SS Stiffner of size 12X25X100X25X12.FOUR (04) NOS 38MM X38MM SQUARE PIPE SS LEGS WITH LEGS ADJUSTABLE BULLET FEET FULL WIDTH 1.2 MM THICK BOTTOM AND MIDDLE SHELFApproved make of SS 304 grade sheet of Jindal, Tata, SAIL or equivalent. |
| 27 | SITC of ISLAND DOUBLE SKIN EXHAUST HOOD WITH FRESH AIR OR FILTER |
| 28 | EXHAUST HOOD SIZE 4000X1250X550EXTERNAL AND INTERNAL PARTS TO BE MANUFACTURED IN SS 3041.2 MM THICK SS WELDED HOOD BODY CONSTRUCTIONFULLLY WELDED JOINTS SHAPE AS PER LAYOUT PLAN SHOULD HAVE REMOVABLE DISHWASHER WASHABLE SS304 grade GREASE FILTERSGREASE DRAIN CHANNEL WITH GREASE TRAYAPPROPRIATE NUMBERS OF FLASHED INCANDESCENT WITH HEAT TOUGHENED GLASS HEAT RESIDENT LED LIGHT WITH IP 55 RATED DIFFUSING GLASS TO PROVIDE 500 LUX OF LIGHT TROUGH OUT THE HOODSHOULD HAVE IP65 ELECTRICAL FITTINGS WIRING SHOULD TO BE done with HEAT RESIDENT CONDUITSHood TO BE PROVIDED WITH ADJUSTABLE DAMPERSTO BE SUSPENDED ON CEILLING WITH 10mm HANGER RODS. Approved make of SS 304 grade sheet of Jindal, Tata, SAIL or equivalent. |
| 29 | SITC of DIUBLE SKIN EXHAUST HOOD WITH FRESH AIR OR FILTER |
| 30 | EXHAUST HOOD SIZE 2400X1250X550EXTERNAL AND INTERNAL PARTS TO BE MANUFACTURED IN SS 3041.2 MM THICK SS WELDED HOOD BODY CONSTRUCTIONFULLLY WELDED JOINTS SHAPE AS PER LAYOUT PLAN SHOULD HAVE REMOVABLE DISHWASHER WASHABLE SS304 grade GREASE FILTERSGREASE DRAIN CHANNEL WITH GREASE TRAYAPPROPRIATE NUMBERS OF FLASHED INCANDESCENT WITH HEAT TOUGHENED GLASS HEAT RESIDENT LED LIGHT WITH IP 55 RATED DIFFUSING GLASS TO PROVIDE 500 LUX OF LIGHT TROUGH OUT THE HOODSHOULD HAVE IP65 ELECTRICAL FITTINGS WIRING SHOULD TO BE done with HEAT RESIDENT CONDUITSHood TO BE PROVIDED WITH ADJUSTABLE DAMPERSTO BE SUSPENDED ON CEILLING WITH 10mm HANGER RODS. Approved make of SS 304 grade sheet of Jindal, Tata, SAIL or equivalent. |
| 31 | THREE BURNER RANGE WITH ONE UNDER SHELF |
| 32 | SIZE 1650X900X850 mm (LXWXH) with 150mm back splashALL MATERIAL AISI 304 GRADEGAS OPRATED3 Nos. H.P. Burner with seperate pilot lampEach burner should have deep tray for collection of overflowALL BURNERS ,WALLS,RV,COPPER PIPE TOTAL MATERIAL IS HPC ISI BRAND1.6 MM THICK SS TOP WITH 3 NOs CAST IRON PAN SUPPORTTOP SECURED TO 38MM X38MMX3MM SS WELDED FRAME WORKBUILT IN PRESSURE CONTROLLER REGULATOR1.2MM THICK SS BOTTOM SHELF100 MM REAR LEGS SETBACK FOR GAS PIPE ROUTING FOUR (04) NOS 38MM X38MM SQUARE PIPE SS LEGS WITH LEGS ADJUSTABLE BULLET FEET Approved make of SS 304 grade sheet of Jindal, Tata, SAIL or equivalent. |
| 33 | SITC of FOUR BURNER RANGE WITH UNDER SELF |
| 34 | SIZE 800X900X850 mm (LXWXH) with 150mm back splashALL MATERIAL AISI 304 GRADEGAS OPRATED4 Nos. H.P. Burner with seperate pilot lamp2 Nos. deep tray for collection of overflowALL BURNERS ,WALLS,RV,COPPER PIPE TOTAL MATERIAL IS HPC ISI BRAND1.6 MM THICK SS TOP WITH 3 NOs CAST IRON PAN SUPPORTTOP SECURED TO 38MM X38MMX3MM SS WELDED FRAME WORKBUILT IN PRESSURE CONTROLLER REGULATOR1.2MM THICK SS BOTTOM SHELF100 MM REAR LEGS SETBACK FOR GAS PIPE ROUTING FOUR (04) NOS 38MM X38MM SQUARE PIPE SS LEGS WITH LEGS ADJUSTABLE BULLET FEET Approved make of SS 304 grade sheet of Jindal, Tata, SAIL or equivalent. |
| 35 | SITC of DEEP FAT FRYER WITH DUAL TANK |
| 36 | DEEP FAT FRYER SIZE-450X900X850 with150 FREE STANDING REAR SPASHELECTRIC OPRATED EQUIPMENTPower - 2x 6 KW (total 12 KW)ALL MATERIAL AISI 304 GRADE CONSTRUCTION 1.6 MM THICK SS TOP2 Nos. FRYING WELL TANKS WITH CAPACITY OF 12.5 LITERS eachTWO TANKS BASKETS , 2 OIL CLARIFYING TRAYS, DEEP COLD ZONE TO COLLECT FOOD DEBRIS HIGH EFFICIENCY HEATING ELEMENTS CONTROL BY HIGH PRECISION THERMOSTATIC REGULATION AND OEVERHEAT SAFETY THERMOSTAT 1.2MM THICK SS BOTTOM SHELFFOUR (04) NOS 38MM X38MM SQUARE PIPE SS LEGS WITH LEGS ADJUSTABLE BULLET FEET Approved make of SS 304 grade sheet of Jindal, Tata, SAIL or equivalent. |
| 37 | SITC of THREE BURNER CHINESE COOKING RANGE |
| 38 | Chinese cooking range-1600X900X850mm (LxBxH) with 360mm High Rear splash & flue riserFree Standing environmental cooking chinese wok rangeFull S.S. 304 GRADE Construction.Top of table to be made in 16 SWG Stainless steel AISI 304 Grade sheet bent 50mm & 12mm all sides, nicely edge-cut, welded & braised.TOP FRAME made with corner angle frame of 38X38X3mm SS 304 grade and apron should be attached with SS Stiffner of size 12X25X100X25X12.Two (02) nos. 400mm dia pans support with high pressure Burner and One (01) nos. rear pan support with low pressure burner with seperate pilot lamps.One (01) no Splash mounted Water faucets (make T&S or aluids or equivalent) to be providedSlanted table top & chamber ringOperation noise level below 70db(A)FOUR (04) NOS 38MM X38MM SQUARE PIPE SS LEGS With nylon adjustable bullet feet.25x25x1.2mm Pipe Undershelf to be provided at bottom with 38x38x3mm SS angle frameApproved make of SS 304 grade sheet of Jindal, Tata, SAIL or equivalent. |
| 39 | SITC of WORK TABLE WITH TWO UNDER SHELF |
| 40 | WORK TABLE SIZE-1250X600X850mm (LXWXH) with 150mm back splashALL MATERIAL AISI 304 GARDE Top of table to be made in 16 SWG Stainless steel AISI 304 Grade sheet bent 50mm & 12mm all sides, nicely edge-cut, welded & braised. Top and UNDER SELF should be SUITABLY JOINT /WELDED to match with the ADJOINING WORK TOP AT SITE. EQUIPMENT TOP PROFILE AS PER LAYOUT PLANTOP FRAME made with corner angle frame of 38X38X3mm SS 304 grade and apron should be attached with SS Stiffner of size 12X25X100X25X12.FOUR (04) NOS 38MM X38MM SQUARE PIPE SS LEGS WITH LEGS ADJUSTABLE BULLET FEET FULL WIDTH 1.2 MM THICK BOTTOM AND MIDDLE SHELFApproved make of SS 304 grade sheet of Jindal, Tata, SAIL or equivalent. |
| 41 | SITC of ISLAND TYPE DOUBLE SKIN EXHAUST HOOD WITH FRESH AIR FILTER |
| 42 | EXHAUST HOOD SIZE 2650X1250X550EXTERNAL AND INTERNAL PARTS TO BE MANUFACTURED IN SS 3041.2 MM THICK SS WELDED HOOD BODY CONSTRUCTIONFULLLY WELDED JOINTS SHAPE AS PER LAYOUT PLAN SHOULD HAVE REMOVABLE DISHWASHER WASHABLE SS304 grade GREASE FILTERSGREASE DRAIN CHANNEL WITH GREASE TRAYAPPROPRIATE NUMBERS OF FLASHED INCANDESCENT WITH HEAT TOUGHENED GLASS HEAT RESIDENT LED LIGHT WITH IP 55 RATED DIFFUSING GLASS TO PROVIDE 500 LUX OF LIGHT TROUGH OUT THE HOODSHOULD HAVE IP65 ELECTRICAL FITTINGS WIRING SHOULD TO BE done with HEAT RESIDENT CONDUITSHood TO BE PROVIDED WITH ADJUSTABLE DAMPERSTO BE SUSPENDED ON CEILLING WITH 10mm HANGER RODS. Approved make of SS 304 grade sheet of Jindal, Tata, SAIL or equivalent. |
| 43 | SITC of Stainless steel PICK UP WORK COUNTER with sink and three side covering and two Overhead Shelf with Heating element. |
| 44 | Overall dimension : 2400X700X850 (LXWXH) mmSink size : 450X450X250 mm made up of SS 304 grade with Mixer faucet (make T&S or aluids or equivalent), coupling and waste pipe.Top of table to be made in 16 SWG Stainless steel AISI 304 Grade sheet bent 50mm & 12mm all sides, nicely edge-cut, welded & braised and to be covered on 3 side with sheet.TOP FRAME made with corner angle frame of 38X38X3mm SS 304 grade and apron should be attached with SS Stiffner of size 12X25X100X25X12.2 Nos. OVER HEAD SELF of size 1500X300 mm & 50mm high back splash placed at 350mm intervals made of 1.2mm thick SS304 grade sheet bent 25mm & 12mm all sides with HEATING ELEMENT supporting on 25 MM 4 Nos. square pipe.Counter Base Legs made up of 40X40X1.2 MM SS 304 grade PIPE and BULLET TYPE ADUJSTABLE BUSH.ALL MATERIAL AISI SS 304 including sheet, pipe, angle, nut & bolt. Undershelf made of 1.2MM SHEET WITH 12X25X100X25X12 mm undershelf stiffner Approved make of SS 304 grade sheet of Jindal, Tata, SAIL or equivalent. |
| 45 | SITC of MOBILE WORK TABLE |
| 46 | TABLE SIZE 1800X350X850 mm (LXWXH) with 150mm back splashALL MATERIAL AISI 304 GARDE Top of table to be made in 16 SWG Stainless steel AISI 304 Grade sheet bent 75mm & 12mm all sides, nicely edge-cut, welded & braised and to be covered on 3 side with sheet.Top and UNDER SELF should be SUITABLY JOINT /WELDED to match with the ADJOINING WORK TOP AT SITE. EQUIPMENT TOP PROFILE AS PER LAYOUT PLANTOP FRAME made with corner angle frame of 38X38X3mm SS 304 grade and apron should be attached with SS Stiffner of size 12X25X100X25X12.FOUR (04) NOS 38MM X38MM SQUARE PIPE SS LEGS WITH (4)NOS HEAVY DUTY WHEELSFULL WIDTH 1.2 MM THICK BOTTOM SHELFApproved make of SS 304 grade sheet of Jindal, Tata, SAIL or equivalent. |
| 47 | SITC of STOCK POT STOVE |
| 48 | STOCK POT STOVE SIZE-750X750X610(LXWXH) WITHOUT SPLASHALL CONSTRUCTION AISI 304 GRADE GAS OPRATED2.MM THICK SS TOP 1 Nos. H.P. Burner with seperate pilot lampTOP BODY SECURE SS FRAME WORK on ALL SIDEs with 25X25x1.2mm SS SQUARE PIPE and CROSS BRACING ,WITH UNDER DEEP TARY BUILT IN PRESSURE REGULATER COTROLLER HPCCounter Base Legs made up of 40X40X1.2 MM SS 304 grade PIPE and ADJUSTABLE BULLETS FEETSApproved make of SS 304 grade sheet of Jindal, Tata, SAIL or equivalent. |
| 49 | SITC of WORK TABLE WITH TWO UNDER SELF |
| 50 | WORK TABLE SIZE-2100X750X850mm (LXWXH) with 150mm back splashALL MATERIAL AISI 304 GARDE Top of table to be made in 16 SWG Stainless steel AISI 304 Grade sheet bent 50mm & 12mm all sides, nicely edge-cut, welded & braised. Top and UNDER SELF should be SUITABLY JOINT /WELDED to match with the ADJOINING WORK TOP AT SITE. EQUIPMENT TOP PROFILE AS PER LAYOUT PLANTOP FRAME made with corner angle frame of 38X38X3mm SS 304 grade and apron should be attached with SS Stiffner of size 12X25X100X25X12.FOUR (04) NOS 38MM X38MM SQUARE PIPE SS LEGS WITH LEGS ADJUSTABLE BULLET FEET FULL WIDTH 1.2 MM THICK BOTTOM AND MIDDLE SHELFApproved make of SS 304 grade sheet of Jindal, Tata, SAIL or equivalent. |
| 51 | SITC of S.S. DRAIN TROUGH GRATING |
| 52 | ALL SS 304 CONSTRUCTIONDRAIN TROUGH GRATING SIZE-(350X350X70)(LXWXH) GRATING OUTER BEARING BAR FRAME WORK OF 38MMX4MM THICK WELDED CONSTRUCTIONGRATING LATERAL /HORIZONTAL CROSS MEMBER OF SIZE 32MMX4MM THICK, PRESSURE LOCKED & UNDER SIDE COMMON FACED TO BE WELDED & REST IN TO SS TROUGH GRATING WITH HAIRLINE FINISHING70MM DEEP 1.6MM THICK SS TROUGH CHANNEL SHAPE, SUITABLE CONSTRUCTION FOR REST GRATINGBASE OF TROUGH SLOPED TOWARDS FLOOR DRAINPROVIDED 100MM DIA CUT & INTERGAL FLANGE FOR ENTRY INTO FLOOR DRAIN ON CUTOUT of 100MM made up of 2.0MM THICK SS PLATE Approved make of SS 304 grade sheet of Jindal, Tata, SAIL or equivalent. |
| 53 | SITC of S.S. DRAIN TROUGH GRATING |
| 54 | ALL SS 304 CONSTRUCTIONDRAIN TROUGH GRATING SIZE-(1200X350X70)(LXWXH) GRATING OUTER BEARING BAR FRAME WORK OF 38MMX4MM THICK WELDED CONSTRUCTIONGRATING LATERAL /HORIZONTAL CROSS MEMBER OF SIZE 32MMX4MM THICK, PRESSURE LOCKED & UNDER SIDE COMMON FACED TO BE WELDED & REST IN TO SS TROUGH GRATING WITH HAIRLINE FINISHING70MM DEEP 1.6MM THICK SS TROUGH CHANNEL SHAPE, SUITABLE CONSTRUCTION FOR REST GRATINGBASE OF TROUGH SLOPED TOWARDS FLOOR DRAINPROVIDED 100MM DIA CUT & INTERGAL FLANGE FOR ENTRY INTO FLOOR DRAIN ON CUTOUT of 100MM made up of 2.0MM THICK SS PLATE Approved make of SS 304 grade sheet of Jindal, Tata, SAIL or equivalent. |
| 55 | COLD ROOM |
| 56 | SITC of DRAIN CHANNEL |
| 57 | ALL SS 304 CONSTRUCTIONDRAIN TROUGH GRATING SIZE-200X200+800X70 (LXWXH) GRATING OUTER BEARING BAR FRAME WORK OF 38MMX4MM THICK WELDED CONSTRUCTIONGRATING LATERAL /HORIZONTAL CROSS MEMBER OF SIZE 32MMX4MM THICK, PRESSURE LOCKED & UNDER SIDE COMMON FACED TO BE WELDED & REST IN TO SS TROUGH GRATING WITH HAIRLINE FINISHING70MM DEEP 1.6MM THICK SS TROUGH CHANNEL SHAPE, SUITABLE CONSTRUCTION FOR REST GRATINGBASE OF TROUGH SLOPED TOWARDS FLOOR DRAINPROVIDED 100MM DIA CUT & INTERGAL FLANGE FOR ENTRY INTO FLOOR DRAIN ON CUTOUT of 100MM made up of 2.0MM THICK SS PLATE Approved make of SS 304 grade sheet of Jindal, Tata, SAIL or equivalent. |
| 58 | SITC of COLD ROOM CHILLAR |
| 59 | Approx. dimension - 1800x2100x2500 mm (WxDXH) or as per site.75mm Each panel is constructed with stainless steel sheets of 0.8mm thick AISI 304 finish No. 4 (hairline) cladding with CFC-Free injected in-place Polyurethane foam.Flooring:-14 gauge Galvanized steel with 75 mm thick insulated panels. Above this cold room floor, Altro flooring and screed will be applied so that the final cold room floor finish is same level as external floor.Unexposed cold room Panel will be pre-painted Galvanized iron sheet 0.8 mm.Wall to wall, wall to ceiling, wall to floor by means of tongue and groove system without any internal and external (holes plug sealed with vinyl caps & rivets) flashing and locked together by cam locks. Other Joinery is not allowed in the cold room.\\"T\\" corners for common cold rooms should form integral 90 DEG corner panels Or Integral \\"T\\" corner panels.Foam density 40Kg/m³ to 44kg/m3Cold Room Floor should be able to withstand loading up to 350kg/m2 & wall 200 kg/m2.Cold Room to have coved corner & Round Edges profile.Adjustable Digital Controller (built-in type) .EVAPORATOR UNIT AS PER BTU OR GUNTER , PATTON , ICE MAKE OR APPROVED AIR COOLED DEVICE WITH SEMI HERMETIC COMPRESSOR BITIZER |
| 60 | SITC of REFRIGERATOR SHELVING |
| 61 | ALL CONSTRUCTION IN AISI 304 GRADE SIZE 1350X600X2000 1.2 MM THICK SS SHELF 4 Nos. 1.2 THICK SS SHELVES 38MM X38 MMX1.6MM THICK SS SQUARE PIPE UPRIGHTS ON NON MARKING RUBBERIZED CATERS WITH 4 NOS HEAVY DUTY WHEELSApproved make of SS 304 grade sheet of Jindal, Tata, SAIL or equivalent. |
| 62 | SITC of COLD ROOM FREEZER |
| 63 | Approx. dimension - 1800x1700x2500 mm (WxDXH) or as per site.100mm Each panel is constructed with stainless steel sheets of 0.8mm thick AISI 304 finish No. 4 (hairline) cladding with CFC-Free Injected in-place Polyurethane foam.Flooring:-14 gauge Galvanized steel with 100 mm thick insulated panels. Above this cold room floor, Altro flooring and screed will be applied so that the final cold room floor finish is same level as external floor.Unexposed cold room Panel will be pre-painted Galvanized iron sheet 0.8 mm.Wall to wall, wall to ceiling, wall to floor by means of tongue and groove system without any internal and external (holes plug sealed with vinyl caps & rivets) flashing and locked together by cam locks. Other Joinery is not allowed in the cold room.\\"T\\" corners for common cold rooms should form integral 90 DEG corner panels Or Integral \\"T\\" corner panels.Foam density 40Kg/m³ to 44kg/m3Cold Room Floor should be able to withstand loading up to 350kg/m2 & wall 200 kg/m2.Cold Room to have coved corner & Round Edges profile.Adjustable Digital Controller (built-in type)Door: Stainless Steel 0.8mm thick on both sides kick plate(1.5mm thick)Door required: Hinged Door (Location as per lay out plan) single-leaf with Hinged channel door 850mm width X 1950mm height, with stainless steel fittings and accessories including rubber gaskets, internal safety release handles, door heaters and pressure port. EVAPORATOR UNIT AS PER BTU OR GUNTER , PATTON , ICE MAKE OR APPROVED AIR COOLED DEVICE WITH SEMI HERMETIC COMPRESSOR BITIZER |
| 64 | SITC of WORK TABLE WITH TWO UNDER SELF |
| 65 | WORK TABLE SIZE-1300X700X850mm (LXWXH) with 150mm back splashALL MATERIAL AISI 304 GARDE Top of table to be made in 16 SWG Stainless steel AISI 304 Grade sheet bent 50mm & 12mm all sides, nicely edge-cut, welded & braised. Top and UNDER SELF should be SUITABLY JOINT /WELDED to match with the ADJOINING WORK TOP AT SITE. EQUIPMENT TOP PROFILE AS PER LAYOUT PLANTOP FRAME made with corner angle frame of 38X38X3mm SS 304 grade and apron should be attached with SS Stiffner of size 12X25X100X25X12.FOUR (04) NOS 38MM X38MM SQUARE PIPE SS LEGS WITH LEGS ADJUSTABLE BULLET FEET FULL WIDTH 1.2 MM THICK BOTTOM AND MIDDLE SHELFApproved make of SS 304 grade sheet of Jindal, Tata, SAIL or equivalent. |
| 66 | SITC of SINGLE WALL SHELF |
| 67 | ALL CONSTRUCTION AISI 304 GRADEWALLL SHELF SIZE-1300x350mm 1.2MM THICK SS WALL SHELVESREAR TURNED UP 50 MM & HEMMED OUSIDEFRONT AND BOTH SIDES TURNED DOWN 38MM & 12MMSHELVES SECURED TO BRACET WITH ACORN SS NUTS & BOLTS2.00 MM THICK SS WALL BRACETS SECURED TO TOP WITH ACORN NUTS & BOLTS BRACKET SECURED TO WALL WITH ANCHOR MOUNTING HEIGHT 1500 A.F.FApproved make of SS 304 grade sheet of Jindal, Tata, SAIL or equivalent. |
| 68 | SITC of CITRUS JUICER |
| 69 | Medium Body SizeBody construction stainless steel 304 grade material Motor Type: Heavy-duty induction motorPower Rating: 200–300 WSpeed: Approx. 1,400–1,500 RPMVoltage: 220–240 V / 50–60 HzProtection: Thermal overload protection APPROVED MAKE KAMAL or THE ONE or equivalent. |
| 70 | SITC of ALL IN ONE JUICER MACHINE |
| 71 | Medium Body SizeBody construction stainless steel 304 grade material Motor Type: Heavy-duty induction motorPower Rating: 200–300 WSpeed: Approx. 1,400–1,500 RPMVoltage: 220–240 V / 50–60 HzProtection: Thermal overload protection APPROVED MAKE KAMAL or THE ONE or equivalent. |
| 72 | SITC of MAKE LINE UNDER COUNTER REFRIGERATOR |
| 73 | REFRIGERATOR SIZE 1800X750X850mmCapacity - 526 Ltr (400W)1.6 MM THICKNESS TOP WITHOUT BACK SPLASH,ALL MATERIAL AISI 304 GRADE0.9mm thick SS 304 grade sheet at back and baseSIX REMOVABLE & ADJUSTABLE SHELVESTHREE DOOR 304 INSULTAION DOUBLE SKIN DOORDOOR OPENING 400MM X600MM for placing of BAKING TRAY ,AMBIENT TEMP 43 degree celcius TEMP WITH AIR COOLED OR AUTO DEFROST. REFEGRATION GAS R-134 A, DIGITAL READ OUT THERMOMETER, TIME DEALY AUTO START, FORCED DRAFT COOLING, condensing cooling light, defrost indicator, fan running indicator, high low temperature alarm.50 MM PU FOAM ON ALL SIDE1/6 GN pan 8 peice with lid.Counter Base Legs made up of 40X40X1.2 MM SS 304 grade PIPE and BULLET TYPE ADUJSTABLE BUSH.APPROVED MAKE WILLIAMS BLR /HOSHIZAKI OR EQUIVALENT |
| 74 | SITC of SANDWICH GRILLER |
| 75 | POWER 2100 WATT355X255 MM SURFACE for BIG SIZE BREADS APPROVED MAKE SIRMAN /THE ONE/GORAV OR EQUIVLNET as approved by Engineer-In-Charge. |
| 76 | SITC of TOASTER |
| 77 | OPERATE WITH 800 WATT, 220 VOLT6 BREAD AT A TIME APPROVED MAKE INES , HATCO OR GORAV or equivalent as approved by Engineer-In-Charge. |
| 78 | SITC of WORK TABLE WITH SINK & SPACE FOR MOBILE EQUIPMENT |
| 79 | ALL MATERIAL AISI 304 GRADE WORK TABLE WITH SINK & SPACE FOR MOBILE EQUIPMENT SIZE-1970X700X850+150(LXWXH) with 150MM HIGH REAR SPLASHSink size - 500x500x250mm with mixer faucet (make T&S or aluids or equivalent), darin valve with overflow, coupling and waste pipe.1.6MM THICK SS TOPRIGHT SIDE OF TOP SUITABLY JOINT/WELDED TO THE ADJOINING WORK TOP AT SITEEQUIPMENT TOP PROFILE AS PER LAYOUT PLAN TOP SECURED TO 12/25MM X75X25/12MMX1.6MM THICK SS HAT TYPE WELDED CHANNEL FRAME WORK Six (06) NOS 38MM X38MM SQUARE PIPE SS LEGS WITH LEGS ADJUSTABLE BULLET FEETFULL WIDTH 1.2 MM THICK BOTTOM AND MIDDLE SHELFApproved make of SS 304 grade sheet of Jindal, Tata, SAIL or equivalent. |
| 80 | SITC of WORK TABLE WITH 2 U/S |
| 81 | WORK TABLE SIZE-1700X700X850mm (LXWXH) with 150mm back splashALL MATERIAL AISI 304 GARDE Top of table to be made in 16 SWG Stainless steel AISI 304 Grade sheet bent 50mm & 12mm all sides, nicely edge-cut, welded & braised. Top and UNDER SELF should be SUITABLY JOINT /WELDED to match with the ADJOINING WORK TOP AT SITE. EQUIPMENT TOP PROFILE AS PER LAYOUT PLANTOP FRAME made with corner angle frame of 38X38X3mm SS 304 grade and apron should be attached with SS Stiffner of size 12X25X100X25X12.FOUR (04) NOS 38MM X38MM SQUARE PIPE SS LEGS WITH LEGS ADJUSTABLE BULLET FEET FULL WIDTH 1.2 MM THICK BOTTOM AND MIDDLE SHELFApproved make of SS 304 grade sheet of Jindal, Tata, SAIL or equivalent. |
| 82 | SITC of ICE CREAM CABINET |
| 83 | Size - 1200x700x850mmHigh-grade Stainless Steel AISI 304Food-grade aluminum or stainless steelHigh-density CFC-free polyurethane foam (minimum 60–70 mm thickness)Rust-proof, heavy-duty construction for continuous operation.Approved Make western or equivalent as approved by Engineer-In-Charge. |
| 84 | SITC of POTATO PILLING MACHINE |
| 85 | CAPCITY 10 KG SINGLE PHASE MACHINE WITH 5 HP MOTOR HEAVY DUTY APPROVED MAKE GLOBAL OR THE ONE or EQUIVLENT as approved by Engineer-In-Charge. |
| 86 | SITC of WET MASALA GRINDER |
| 87 | MASALA GRINDERS-15 KGS WITH 3 HP SINGLE PHASE CAPCITYSingle stone TYPE MUG SS 304 APPROVED MAKE LAXMI or THE ONE OR equivalent as approved by Engineer-In-Charge. |
| 88 | SITC of DOUGH MIXER-25 KGS |
| 89 | DOUGH KNEADER MACHINE WITH CAPCITY 15 KG TO 25 KG AATA MIXER CAPCITY HAVY BASE MS PLATE WITH STAINLESS STEEL BOWL BASE COVER WITH STAINLESS STEEL SHEET OPERATED BY DOMESTIC POWER SUPPLY WEIGHT APPROX 80 KG ELECTRIC MOTOR 1 HP ,RPM 1440 , VOLTAGE 220 V POWER CONSUMPTION 0.75 UNIT MATERIAL SS 304 SEMI AUTOMATIC APPROVED MAKE KAML ,THE ONE , LAXMI ,GORAV or equivalent as approved by Engineer-In-Charge. |
| 90 | SITC of TWO TEAR TROLLEY |
| 91 | ALL CONSTRUCTION IN AISI 304 GRADE 2.00 MM THICK SS TOP and bottom SS sheetTOP AND BODY SECURED TO 38MM X38MM X3 MM THICK SS WELDED ANGLE FRAME WORK38MM DIA SS PIPE HANDLE WITH PIPE REINFORCEMENT150MM HIGH 12MM DIA SS PIPE RAILLING FRONT & REAR SIDES FOUR (04) NO. HEAVY DUTY 125MM DIA NON MARKING RUBBERIZED CASTERS ALL WITH BRAKES.Approved make of SS 304 grade sheet of Jindal, Tata, SAIL or equivalent. |
| 92 | SITC of PLATFORM TROLLEY |
| 93 | ALL CONSTRUCTION IN AISI 304 GRADE2.00 MM THICK SS TOP CHANNEL SHAPETOP AND BODY SECURED TO 38MM X38MM X3 MM THICK SS WELDED ANGLE FRAME WORK38MM DIA SS PIPE HANDLE WITH PIPE REINFORCEMENT150MM HIGH 12MM DIA SS PIPE RAILLING FRONT & REAR SIDESFOUR (04) NO. HEAVY DUTY 125MM DIA NON MARKING RUBBERIZED CASTERS ALL WITH BRAKESApproved make of SS 304 grade sheet of Jindal, Tata, SAIL or equivalent. |
| 94 | SITC of L SHAPE DISH DROP OFF TABLE WITH GLASS RACK & GARBAGE CHUTE |
| 95 | ALL CONSTRUCTION IN AISI 304 GRADESize :- 1965x750+600x750x850mm with 150mm high back splashsink size - 500x500x250mm made up of SS 304 grade with mixer faucet (make T&S or aluids or equivalent), coupling and waste pipe.1.6 mm thick stainless steel sheet for durability 2 nos. Garbage Chute OVERHEAD GLASS RACK SELF made of 1.2 MM thick SS304 grade size -1965x450mm for glass tray supporting on 25 MM 4 Nos. square pipe.Counter Base Legs made up of 40X40X1.2 MM SS 304 grade PIPE with cross-bracing for rigidity and BULLET TYPE ADUJSTABLE BUSH.Approved make of SS 304 grade sheet of Jindal, Tata, SAIL or equivalent. |
| 96 | SITC of PRE RINGE SPRAY UNIT |
| 97 | EASY INSTALL PRE RINSE SPRING ACTION SWIVEL8\\" DECK MOUTED MIXING FAUCET WITH POLISHED CHROME PLATED BRASS BODY18 '' RISER & FLEXIBLE STAINLESS STEEL HOSE WITH HEAT RESISTANT HANDLE AND SWIVEL1.15 GPM spray valve, compression cartridges with spring checks12MM NPT FEMALE INLETS 6'' ADJUSTABLE WALL BRACKETCERTIFIED TO ASME A112 .18.1/CSA B125.1 NSF 61-SECTION 9 AND NSF 372. EP ACT 2005 COMPLIANT .APPROVED MAKE T&S, ALUDIUS OR EQUIVELANT as approved by Engineer-In-Charge. |
| 98 | SITC of VAPOUR HOOD |
| 99 | SIZE- 1400x1000x550mm ALL CONSTRUCTION IN AISI 304 GADE1.2MM THICK SS WELDED HOOD BODY CONSTRUCTION FULLLY WELDED JOINTS SHAPE AS PER LAYOUT PLANSHOULD HAVE REMOVABLE DISHWASHER WASHABLE SS GREASE FILTERS GREASE DRAIN CHANNEL WITH GREASE TRAYAPPROPRIATE NUMBERS OF FLASHED INCANDESCENT WITH HEAT TOUGHENED GLASS HEAT RESIDENT LED LIGHT WITH IP 55 RATED DIFFUSING GLASS TO PROVIDE 500 LUX OF LIGHT TROUGH OUT THE HOODApproved make of SS 304 grade sheet of Jindal, Tata, SAIL or equivalent. |
| 100 | SITC of HOOD TYPE DISH WASH MACHINE |
| 101 | Type: Passthrough Hood Type Dishwasher.Capacity: Up to 60 racks per hour (20 racks/hour in High Temp mode).Rack Size: 500 x 500 mm.Programs: 2 (Standard & High Temp).Water Consumption: ~2.4 liters per rack.Final Rinse Temp: 85°C (ensured by Thermostop).Tank Capacity: 28 Liters.Power: ~9 kW (Boiler).Dimensions (W x D x H): Approx. 735 x 750 x 1500 mm (varies slightly by source).Noise: Max 63 dB(A). approved make electrolux /winterhalter or hobart equivelent |
| 102 | SITC of CLEAN DISH ROLLERS TABLE |
| 103 | ALL CONSTRUCTION IN AISI 304 GADESize :- 1800x750x850mm (LxBxH) with 250mm high black splash2.00MM THICK SS TOPREMOVABLE FULL LENGH PLASTIC NYLON ROLLERS TO BE PROVIDEDRight/ Left side attached with dish washerEQUIPMENT TOP PROFILE AS PER LAYOUT PLANTOP SECURED 25MM X100MM X25 X1.6 THICK FRAME WORK4 Nos. 38MM X38 MMX1.6MM THICK SS SQUARE PIPE legs with SS ADJUSTABLE BULLET FEETFULL WIDTH 1.2 MM THICK BOTTOM AND MIDDLE SHELFApproved make of SS 304 grade sheet of Jindal, Tata, SAIL or equivalent. |
| 104 | SITC of DISH RACK |
| 105 | SIZE 1250X600X2000mm (LXWXH)ALL CONSTRUCTION IN AISI 304 GRADE4 Nos. 1.2mm THICK SS SHELVES FRONT TURNED UP 12MM @ 45 DEG REAR & BOTH SIDES TURNED UP 50MM & HEMMED each self have support stiffner with 25x100x2538MM X38 MMX1.6MM THICK SS SQUARE PIPE UPRIGHTS with adjustable bushApproved make of SS 304 grade sheet of Jindal, Tata, SAIL or equivalent. |
| 106 | SITC of SOAKING TROLLEY |
| 107 | ALL CONSTRUCTION AISI 304 GRADESOAKING TROLLEY SIZE-(610X610X610 )1.6 MM THICK SS WALL SIDES CHNANNEL SHAPE535 MM X535MM DEEP1.6 MM THICK SS WITH ALL CORNER COVED 20MM RADIUSCOMPLETE WITH TAIL PIPE EXTENDED AT 50MM A.F.F FOUR (04) NO.38MM X38MM X1.6MM THICK SS LEGS, 25MM X25MM X1.6MM THICK CROSSS BRACING AT ALL SIDES(04) NO. 100 DIA NON MARKING RUBBERIZED CASTERS, TWO WITH BRAKES.SS CHOPPING BOARD STAND APPROX 200 MM X6MM THICK SS ROD (REMOVABLE).Approved make of SS 304 grade sheet of Jindal, Tata, SAIL or equivalent. |
| 108 | POT WASH AREA |
| 109 | SITC of POT WASH THREE SINK UNIT |
| 110 | POT WASH THREE SINK SIZE-2100X750X850mm with Mixer Faucet (2 Nos.) (make T&S or aluids or equivalent), drain valve with over flow (3 Nos), coupling and waste pipe with 150MM HIGH REAR & LEFT SIDE SPLASH ALL CONTRUCTION AISI 304 GRADE 1.6MM THICK SS TOPTOP SECURED TO 12/25MM X75MM X25/12MMX1.6MM THICK SS HAT TYPE WELDEDCHANNEL FRAME WORK THREE (3) NOS. 500MM X500MM X250MM DEEP 1.6MM THICK SS SINKS COMPLETE WITH 50 MM DIA LEVER HANDLE OPRATED WASTE OUTLET & REAR CONNNECTED OVERFLOWSIX (6) NOS 38MMX38MM X1.2MM THICK SS SQUARE PIPE LEGS WITH SS NYLON ADJUSTABLE BULLET FEET1.00MM THICK SS APRON FRONT SIDE OF SINK.Approved make of SS 304 grade sheet of Jindal, Tata, SAIL or equivalent. |
| 111 | SITC of PIPE WALL SHELF |
| 112 | ALL CONSTRUCTION IN AISI 304 GRADESIZE -1200X350shelf made with 5 no 25 mm round pipe with bracket & BOLTS2.00 MM THICK SS WALL BRACETS SECURED TO TOP WITH ACORN NUTS & BOLTS BRACKET SECURED TO WALL WITH ANCHOR, MOUNTING HEIGHT 1500 A.F.F.Approved make of SS 304 grade sheet of Jindal, Tata, SAIL or equivalent. |
| 113 | SITC of MOBILE POT RACK |
| 114 | All construction in AISI 304 grade size 1000x600x1900 Four (4) nos. S.S. pipe shelves. First shelf 300 A.F.F., Second 900 A.F.F., Third shelf 1375mm A.F.F., & Fourth shelf at 1850mm A.F.F. Shelf outer tube 32mm dia S.S. pipe with 25mm dia S.S pipe welded to outer tube at 75 c/c Four (4) nos. 38mm dia S.S. pipe upright with 4 no adjustable bush.Approved make of SS 304 grade sheet of Jindal, Tata, SAIL or equivalent. |
| 115 | SITC of S.S. STORAGE RACK |
| 116 | ALL CONSTRUCTION IN AISI 304 GRADE SIZE 1250X600X2000 5 nos. 1.2 THICK SS SHELVES i/c top38MM X38 MMX1.6MM THICK SS SQUARE PIPE UPRIGHTS ON NON MARKING RUBBERIZED CATERS WITH 4 NOS HEAVY DUTY WHEELSFOUR SHELF FOR STORAGE Approved make of SS 304 grade sheet of Jindal, Tata, SAIL or equivalent. |
| 117 | SITC of Water Hose Reel Station |
| 118 | Heavy duty cast bronze mixer bodyFurnished with steel enclosed braided Dunlop hose of 15M long with brass end nozzle at working endSS swing wall bracketreel rack with stud bolt for anchoring to rear wallBrass Ball ValveSS pipe fittings, inductor & flangesApproved make Jephyer ZWR1315 or ALUIDS C8289 or Equivalent as approved by Engineer-In-Charge. |
| 119 | PROVIDING OF MATERIAL, COMMISSIONING AND INSTALLATION OF 5 X 2 (10 LPG CYLINDER) MANIFOLD GAS BANK SYSTEM AS PER THE SITE LAYOUT PLAN & AS PER THE GUIDELINES LAYED BY THE APPROVED GOVT. OF INDIA UNDERTAKING PETROLEUM COMPANY (HPC/BPC/INDANE). THE WORK SHALL STRICTLY BE IN ACCORDANCE WITH THE SUPERIOUR QUALITY PARAMETERS. LAYING OF PIPE, CLAMPING, WELDING SHOULD BE IN RIGHT ANGLE AND IN GOOD FINISH. PRESSURE HOLDING TEST SHALL BE CONDUCTED OF THE ENTIRE GAS BANK SYSTEM.SCOPE OF WORK |
| 120 | LPG line with GAS BANK (5 × 2 CYLINDER MANIFOLD SYSTEM),including LPG cylinder bank of 14.2 kg each LPG cylinder with: 'C' class seamless M.S pipe conforming to IS:1239 : 2” for gas bank pipe laying and 1” for rest pipe laying, with Pressure regulator - Upto 30 PSI (dial type) and supported with wall by providing adequate supports spacing not more than 1.5 mtr., fitted with flanges & accessories and isolation valves having ball valves of approved makes with LPG installation certificate having carbon steel body, SS ball and PTFE seat and all other fittings such as tees, reducers, unions, elbows etc. The piping shall be joined through welding by using welding electrode of ISI marked only. Care must be taken to prevent rusting of piping installation by providing red oxide primer coating and suitablesleeve of GI/wood shall be provided wherever the pipes are crossing through the walls/slabs etc. On completion, the LPG manifold complete with all accessories and individual components which are subjected to cylinder pressure shall be capable of withstanding a test pressure twice the working pressure. |
| 121 | All the accessories, components used for installation of LPG pipeline system shall have the approval from Oil company i.e. IOCL/HP/BP. Isolation/shut off valves shall be ball valves with installation certificate for use in LPG pipelines and shall have carbon steel body, stainless steel ball and PTFE seat. The work includes supply, installation, testing and commissioning of LPG manifold and supply system with at least two coat paints as per LPG color norms. The items covered under scope of works shall include all those ancillary items which may be required to complete the work in all respect whether specifically mentioned or not. Fire fighting arrangements for LPG bank should be as per the guidelines of statutory body/local authority/local government.Preferred make - MS pipe of JINDAL / TATAA. MATERIAL TO BE USED |
| 122 | I. Flame Arrester 1” (UNITED/VANAZ) |
| 123 | II. Gas Filter 1” (UNITED/VANAZ) |
| 124 | III. Click -On Adopter (UNITED MAKE) |
| 125 | IV. Cylinder Flexible Pigtail (SURAKSHA MAKE) |
| 126 | V. Brass NRV (Non return valve) (HPC MAKE) |
| 127 | VI. Manifold Valve 2\\" (L&T Make) |
| 128 | VII. Adjustable Pressure Regulator (UNITED MAKE) |
| 129 | VIII. Pressure Gauge 3/8\\" (H GURU/ WAREE MAKE) |
| 130 | IX. 1\\" Main Line Valve (L&T MAKE) |
| 131 | X. ½\\" Main Line Valve (L&T MAKE) |
| 132 | XI. 1\\" M.S Tata Seamless C Class Pipe With V/S Make Multiple Fitting's (TATA MAKE) |
| 133 | XII Manifold system 5x2 (2\\" Tata C Class) |
| 134 | XIII DVC 1\\" Seamless |
| 135 | XIV Regulator first stage R2301 (VENZ Make) |
| 136 | XV. ½\\" M.S Tata Seamless C Class Pipe With V/S Make Multiple Fitting's (TATA MAKE) |
| 137 | XVI Needle Control Valve (½\\" x 3/8\\") (HPC MAKE) |
| 138 | XVII Burner Pigtail (SURAKASHA MAKE) |
| 139 | XVIII M.S Wall Clamp |
| 140 | COMMISSIONING & INSTALLATION COSTCost incurred in Commissioning & Installation Of 5 x 2 (10 Cylinder)Manifold Gas Bank System as Per the Material Details given above & as complete one job ready-to- operation . |
| 141 | SITC of MICROWAVE OVEN (Convection 30 Ltr.) |
| 142 | 30 L capacityconvention oven ideal for baking, grilling, reheating, defrosting and cooking, offering versatile performancefinish type - mettalicTouch keypad (membrane) Approved make IFB or Equivalent as approved by Engineer-In-Charge. |
| 143 | SITC of PLATFORM WEIGHING MACHINE |
| 144 | Capacity 200 kg., Accuracy 20 gm., Platter size 500 MM X 500 MMBench scale electronic weighing machine fabricated with heavy duty rugged construction with flexible indicator with attached stand, having stainless steel platter and back rail, having built in multi function such as add weighing memory, piece counting litre conversion, extra zero facility etc. with LPCM.Approved make Satwik or phoenix or equivalent as approved by Engineer-In-Charge. |
| 145 | SITC of Masala Grinder |
| 146 | 3-12 kg/ hour capacity 4 Nos. SS Jar with lid Unique coarse grinding blade with blunt edge replicate traditional stone grinding for dry masalaSingle Phase, Capacity 2500WApproved make Sumo or equivalent as approved by Engineer-In-Charge. |
| 147 | SITC of Pulvrizer |
| 148 | 5 HP, single phase Pulvrizer, 220-240VHigh capacity with commercial grade unitcapacity ranging from 30-150kg per hour2880 RPM motorApproved make Laxmi or equivalent as approved by Engineer-In-Charge. |
| 149 | SITC of Pizza Oven |
| 150 | Size - 600x470x310mm Suitable for 2 Large size PizzasSingle DeckElectric stone Pizza Oven SS Body materialSingle phase, Power capacity 2.5-3 KWTemp. range upto 400 Deg. C.Approved make Middleby or truefrost or equivalent as approved by Engineer-In-Charge. Please Enable Macros to View BoQ information |
