|
| 1 | Clearing Grass and Removal of Rubbish Clearing grass and removal of rubbish up to a distance of 30 m outside the periphery of the area as per MoRD Technical Specification Clause 201. |
| 2 | Removal of Telephone/ Electric Poles and LinesRemoval of telephone/ electric poles with wires including excavation and dismantling of foundation concrete andlines under the supervision of concerned department, disposal with all lifts and upto a lead of 1000 m and stacking the serviceable and unserviceable material separately as per MoRD Technical Specification Clause 202. |
| 3 | Scarifying Existing Bituminous Surface to a depth of 150 mm by Mechanical MeansScarifying Existing bituminous Road Surface by mechanical means to a Depth of 150 mm and disposal of scarified material with a lift upto 3 m and leads upto 1000 m as per MoRD Technical Specification Clause 301.4. |
| 4 | Construction of Embankment with Material Obtained from Borrow PitsConstruction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 1000 m as per MoRD Technical Specification Clause 301.5. |
| 5 | Construction of Subgrade and Earthen ShouldersConstruction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site , spreading, grading to required slope and compacted to meet requirement of Table 300.2 as per MoRD Technical Specification Clause 303.1. |
| 6 | Construction of road side pucca drain with M10 (1:3:6 with jhama brick aggregate) to specified lines, grades, levels and dimensions as per approved design and MoRD Technical Specification Clause 307, 1606. Excavated material to be used in embankment at site. (including centering, shuttering, etc. but excluding reinforcement) B. Trapezoidal drain (top clear width 600 mm, bottom clear width 300 mm and clear depth of 400 mm)I. In Ordinary Soil |
| 7 | Surface DrainsConstruction of unlined surface drains of average cross-sectional area 0.40 sqm in ordinary soil to specified lines, grades, levels and dimensions. Excavated material to be used in embankment with a lift upto 3 m and lead of 50 m (average lead 25 m) as per MoRD Technical Specification Clause 307.(i) Surface Drains in Ordinary Soil (A) Manual Means |
| 8 | Granular Sub-base with Well Graded Material (Table 400.1)(A) By Mix in Place MethodConstruction of granular sub-base by providing wellgraded material (Jhama Brick Aggregate, Grading-I, as per Table 400.1, spreading in uniform layers with tractor with attachments on prepared surface, mixing by mix in place method with rotavator at OMC, applying and brooming sand to fill up the interstices of coarse aggregate, watering and compacting with smooth wheel roller to achieve the desired density, complete as per MoRD Technical Specification Clause 401.(i) For Grading - I Material (jhama brick aggreate) |
| 9 | Water Bound Macadam Sub-Base / Base using Jhama BrickAggragate 1) WBM Grading - 2Providing, laying, spreading and compacting jhama brick aggregates of specific sizes to water bound cadam specification including spreading in uniform thickness, hand packing rolling with three wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming binding materials to fill up the interstices of coarse aggregate, watering and compacting to the required density Grading- 2 as per MoRD Technical Specification Clause 405.(A) By Manual Means |
| 10 | Water Bound Macadam Sub-Base / Base(2) WBM Grading 3Providing, laying, spreading and compacting jhama brick aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing rolling with three wheel roller 80-100 kN in stages to proper grade and camber, applying and brooming binding materials to fill up the interstices of coarse aggregate, watering and compacting to the required density Grading- 3 as per MoRD Technical Specification Clause 405.(A) By Manual Means |
| 11 | Prime Coat(i) Low porosityProviding and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70- 1.00 kg/sqm using mechanical means as per MoRD Technical Specification Clause 502. |
| 12 | Tack Coat(i) Providing and applying tack coat with bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.20 to 0.25 kg per sqm on the prepared bituminous surface cleaned with Hydraulic broom as per MoRD Technical Specification Clause 503. |
| 13 | 25 mm thick Open-Graded Premix Carpet using Bituminous(Viscosity grade/ modified bitumen) Binder Providing, laying and rolling of open-graded premix carpet of 25 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using Viscosity grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80 - 100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C or Type D as per MoRD Technical Specification Clause 508.Case - I By Manual Means(I) Bitumen of VG-30 |
| 14 | Seal CoatProviding and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type A or Type B or Type C or Type D as per MoRD Technical Specification Clause 510.Case - IV : Type D (premix with fine sand)(I) Bitumen of VG-30 |
| 15 | Excavation for Structures(A) Without dewatering.Earthwork in excavation for structures as per drawing and MoRD technical specifications Clause 305.1 including setting out, construction of shoring & bracing, removal of stumps & other deleterious material and disposal upto a lead of 50 m, dressing of sides & bottom and backfilling in trenches with excavated suitable material.(A) Ordinary Soil (i) upto 3 m depth |
| 16 | Filling in foundation trenches as per drawing & MoRD technical specification Clause 305.3.9, 1200.(i) Sand filling |
| 17 | Providing concrete for plain/reinforced concrete in open foundations complete including formwork as per drawings & MoRD technical specifications Clauses 802, 803, 900, 1202 and 1203. (including centering, shuttering, staging etc. but excluding reinforcement).II P.C.C grade M 15(i) Nominal mix (1:2.5:5) |
| 18 | Providing concrete for plain/reinforced concrete in open foundations complete including formwork as per drawings & MoRD technical specifications Clauses 802, 803, 900, 1202 and 1203. (including centering, shuttering, staging etc. but excluding reinforcement).VI. R.C.C grade M-25i) upto 5 m height |
| 19 | Supplying, fitting & placing Thermo-Mechanically treated bar/ Cold twisted deformed steel bar in substructure complete as per drawings & MoRD technical specification Clauses 1002, 1005, 1010 and 1202. |
| 20 | Providing weep holes in brick masonry/ stone masonry, plain/ reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe or uPVC pipe (110 mm OD of 6.0 kg/cm2 pressure) extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and MoRD technical specification clauses 614, 709, 1204.3.7. |
| 21 | Providing & laying filter media with jhama brick aggregates as per specification to a thickness of not less than 600 mm with smaller size towards the soil & bigger size towards the wall & providing over the entire surface behind abutment, wing wall, return wall to the full height, compacted to firm condition complete as per drawing and MoRD technical specification clause 1204.3.8. |
| 22 | Excavation for StructuresA. Earth work in excavation for structures as per drawing and MoRD technical specification clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material.i. Ordinary Soil(A) By mechanical Meansi. Upto 3 m depth |
| 23 | Filling in foundation trenches as per drawing & MoRD technical specification Clause 305.3.9, 1200.i. Sand filling |
| 24 | Providing concrete for Plain/Reinforced Concrete in open Foundation complete as per drawings and MoRD technical specifications clauses 802, 803, 900, 1202 and 1203.(including centering & shuttering, staging etc. but excluding reinforcement.)A. PCC M-15 Grade(i) Nominal mix (1:2.5:5) |
| 25 | Providing weep holes in Brick masonry/Stone masonry,Plain/ Reinforced concrete butment, wing wall/ return wall with 100 mm dia AC pipe or PVC pipe(110 mm OD of 6.0 Kg/cm2 pressure) extending through the full width of the structure with slope of 1V :20H towards drawing face complete as per drawing and MoRD Technical Specifications clauses 614, 709, 1204.3.7 |
| 26 | Plain/Reinforced cement concrete in sub-structure complete including formwork as per drawing and MoRD Technical Specification clauses 802, 804, 805, 806, 807, 900, 1202 & 1204 (including centering & shuttering, staging etc. but excluding reinforcement.). vi. RCC M 25 Gradea ) Upto 5 m height (Case-I) (using concrete mixer) |
| 27 | Supplying, Fitting and Placing Thermo-Mechanically treted bar / Cold twisted deformed steel bar Reinforcement in Substructure complete as per Drawing and MoRD Technical Specification Clauses 1002, 1005, 1010 & 1203 |
| 28 | Providing and laying filter media with jhama brick aggregates as per specification to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and providing over the entire surface behind abutment, wing wall, return wall to the full height, compacted to firm condition complete as per drawing and technical specification Clause 1204.3.8 |
| 29 | Providing PCC M 20 (with jhama brick aggregate) architectural coping on the top of wing wall, return wall etc. complete including formwork as per drawing & MoRD technical specification Clauses 615, 710 & 1204.3.11. |
| 30 | Providing and laying Reinforced cement concrete in superstructure as per drawings and MoRD technical specifications Clauses 800, 900, 1205.4 & 1205.5.(including centering, shuttering, staging etc but excluding reinforcement.)(ii) RCC Grade M 25 1. - Upto 5 m height |
| 31 | Supplying, fitting, and placing Thermo-Mechanically treated bar/ Colt twisted deformed steel bar reinforcement in superstructure complete as per drawings & MoRD technical specification Clauses 1002, 1010, 1202 |
| 32 | Providing and fixing in position Drainage spouts complete as per drawing & MoRDE technical specifications Clause 1209. |
| 33 | Reinforced Cement Concrete Crash BarrierProvision of an Reinforced cement concrete crash barrier at the edges of the road, approaches to bridge structures and medians, constructed with M-20 grade concrete with TMT reinforcement conforming to IRC:21 and dowel bars 25 mm dia, 450 mm long at expansion joints filled with pre- moulded asphalt filler board, keyed to the structure on which it is built and installed as per design given in the enclosure to MOST circular No. RW/NH - 33022/1/94-DO III dated 24 June 1994 as per dimensions in the approved drawing and at locations directed by the Engineer, all as specified as per MoRT&H Technical Specification Clause 811 |
| 34 | plastering with cement mortar (1:4) 12 mm thick on brickwork/ C.C. work including a finishing coat of neat cement punning with 2.75 kg of cement per sqm in substructure as per MoRD technical specification Clauses 613.4 & 1204. |
| 35 | Providing and laying of apron with cement concrete blocks of size as per Table 1300.1cast-in-situ and made with a) Concrete grade M 15 Please Enable Macros to View BoQ information |
