|
| 1 | BUILDING WORKS (F) STRUCTURAL STEEL WORKS, GRILLS,GATES ETC. A. ORIGINAL WORKS 3. Cutting to requisite length or shape departmental R.S. joists,channels, angles, tees, plates etc. (Payment to be made on area of cut surface) |
| 2 | BUILDING WORKS ( C ) Brickworks,Concrete Works etc?36...Hire and labour charges for shuttering with centering and necessary staging upto 4 m using approved stout props and thick hard wood planks of approved thickness with required bracing for concrete slabs, beams and columns, lintels curved or straight including fitting, fixing and striking out after completion of works (upto roof of ground floor).(When the height of a particular floor is more than 4 m the equivalent floor height shall be taken as 4 m and extra for works beyond the initial 4 m ht. shall be allowed under 12 (e) for every 4 m or part thereof).(a) 25 mm to 30 mm thick wooden shuttering as per decision & direction of Engineer-In-Charge.Notes:- For shuttering in shell roof, grid roof with vertical faces folded plate, arched roof the rate in 36 (a), 36 (b) & 37 (c ) of subhead B above to be increased by 100 % . For grid roof with splayed faces, rate is to be increased by150%. |
| 3 | M.S PLATE AS PER IS : 2062 -2011/LATEST REVISION, MAKE : SAIL/ TATA/JINDALC) ABOVE 10 MM UPTO 20 MM THICKNESS |
| 4 | I.S.M.B AS PER IS : 2062 -2011/LATEST REVISION, MAKE : SAIL/TATA/JINDALC) ABOVE 300 X 140 |
| 5 | FABRICATION , SUPPLY, ERECTION AND COMMISSIONING OFEMBEDED |
| 6 | BUILDING WORKS (F) STRUCTURAL STEEL WORKS, GRILLS,GATES ETC. B. REPAIRING 2. Welding in M.S. structural work with gas or electric: (a) Tack weld |
| 7 | BUILDING WORKS (F) STRUCTURAL STEEL WORKS, GRILLS,GATES ETC. B. REPAIRING 2. Welding in M.S. structural work with gas or electric: (b) Continuous weld. |
| 8 | SANTRAS |
| 9 | ORDINARY CEMENT CONCRETE ( MIX 1:2:4 ) WITH GRADED STONE CHIPS ( 20 MM NOMINAL SIZE) EXCLUDING SHUTTERING AND REINFORCEMENT, IF ANY, IN GROUND FLOOR AS PER RELEVANT IS CODES (BASED ON PWD SCHEDULE OF RATES, W.E.F. 01.11.2017 WITH CORRIGENDADT.04.06.2018) |
| 10 | SECTION 1 BUILDING WORKS (I) PLASTERING,POINTING ETC. A. ORIGINAL WORKS 1.Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface](ii) With 1:4 cement mortar (a) 20 mm thick plaster |
| 11 | MANUFACTURING OF EN 24 LEAD SCREW OF SIZE (75 MM DIA.X 7500 MM LONG) FOR THE OPERATING GATE. |
| 12 | MANUFACTURING OF G.M LEAD NUT TO SUIT WITH THE LEADSCREW. |
| 13 | MANUFACTURING AND FITTING OF PEDESTAL FOR THEINSTALLING OF PENSTOCK GATE WITH PROPER ALIGNMENT. |
| 14 | MANUFACTURING OF C.I HAND WHEEL (20 INCH) FOROPERATION OF GATE |
| 15 | Estimated amount |
| 16 | Add: 9%SGST |
| 17 | Add: 9%CGST |
| 18 | 1% LWC Please Enable Macros to View BoQ information |
