|
| 1 | Providing & repairing of 15 HP, 2980 RPM, 35 mtr. head 3 phase monoblock kirlosker make 3 motor pump set at bharatpuri pump house including following the parts & work . |
| 2 | Carefully disconncting of above motor pump set at suction & delivery base plate i/c complete servicing of pump chamber pulley movement of impeller unit with fitting. |
| 3 | Providing & fixing of oil seal |
| 4 | Providing & fixing of pump ball bearing and trust bearing make any standard |
| 5 | Providing & fixing G.M. long bush. |
| 6 | Complete refitting on pump after repairing & checking of horizontal and vertical alignment of motor pump set, coupling with pump and trial testing etc. i/c including loading and unloading charge site to work shop and back. |
| 7 | Providing & fixing G.I. gland bush. |
| 8 | Providing & making of bearing sheet by welding & lath machine turning & polishing on pump shaft. |
| 9 | Providng & complete servicing of pump chamber fully movement of impuller unit with us per required fitting work including check nut bolt, wiser, oil paper etc. complete |
| 10 | Providing and making 150 MM dia foot valve flute plate including i/c cutting of old damaged nut bolts and recasting finishing machining packing & complete nut bolt for fitting and section pipe line at site. |
| 11 | Providing & cleaning of slot by CTC and removing moisture then varnishing and drying by heating process. |
| 12 | Providing & fixing of drive & non driver bearing as per required leth work for motor. |
| 13 | Providing and fixing of terminal plate. |
| 14 | Providing & fixing making of diamtrically balancing rotor assembley |
| 15 | Providing & complete rewinding work of 15 H.P, 440 volt 3 phase mono block motor cutting of burnt winding wire & slots malted chips material from slots cleaning & decarborizing of complete stator slots rotor etc. making of supper enambelled copper in sulated new coils fixing in the stator slots insulation etc complete i/c soldering brazing refitting of rewinding motor allingment and dynamically balance of rotor horizontal allingment with pump trial & testing etc, complete job |
| 16 | Providing & fixing of C.I. motor cooling fan |
| 17 | Complete refitting on motor & base plate checking of horizontal & verticle alignment of motor pump set, coupling with pump & trail & testing etc i/c loading, unloading charge site to work shop & back. |
| 18 | Providing & complete servicing of pump chamber fully movement of new impuler unit with as per required fitting work including check nut, nut-bolt, wiser, oil paper etc. complete. |
| 19 | Providing & complete repairing, replacing burnet equipment for 15 H.P. penal with 3 set starter & power supply wiring i/c the following works |
| 20 | Labor charge for complete repairing of 15 H.P. penal with 3 starter complete repair, replacement of tripping system changing of conctact & burnet equipment replacement with complete power, control wiring of panel starter i/c trail & testing at site on load. |
| 21 | Providing for complete replacing 250/300 ampere, 415 volt 50 Hz moulded case cricuit breaker (MCCB) of any standard make for main power supply equipment. |
| 22 | Providing & fixing of indication lamp |
| 23 | Providing & fixing of relay unit range 28-42 amp. |
| 24 | Providing & fixing of ML-4 contactor |
| 25 | Providing & fixing of ML-2 contactor |
| 26 | Providing & fixing of ML-1.5 contactor |
| 27 | Providing & fixing of on/off switch |
| 28 | Providing & fixing of timer assembly |
| 29 | Providing & fixing of 63 amp. MCCB, 415 v., 50 hz., for star delta starter |
| 30 | Providing & fixing of ampier meter 0-100 amp. |
| 31 | Providing & fixing of volte meter 0-500 v. |
| 32 | Providing & fixing of current transformer. (CT) range 100-200/5 amp. for majouring of main panel ampier |
| 33 | Provding & fixing of heavy duty capacitor 440 v. 7.5 KVAR capacitor with complete as per required work. |
| 34 | Labor charge for complete repairing opening & refitting of 150 mm dia non return valve & sluice valve i/c cutting of old damaged nut bolt & providing recasting finishing, machining of gate plate holding rod assembly as per sample & required packing, complete nut bolt for fitting on delivery pipe line at site as per following items. |
| 35 | Supply of S.S. 410 spindle rod without G.M. check nut for 150 mm. dia. |
| 36 | Recasting of 150 mm dia sluice valve G.M. check nut i/c recasting, finishing, machining & threading as per sample & cost of extra material complete work. |
| 37 | Repairing of 150 mm. dia. sluice valve C.I. fixture check nut catcher both side i/c welding, finishing cutting as per size of check nut. |
| 38 | Labor charge of opening & refitting of 150 mm. dia. sluice valve i/c cutting of old damaged nut bolt, removal of damaged gland packing, rubber packing, providing, fixing of new by fabricated parts & greasing properly cost of nut bolt, over hanting the valve transportation of material T&P testing & making with risk cover as per requirement. |
| 39 | Providing & fixing of presure gauge meter 0.0 to 7 or 0.0 to 10 Kg./cm2 size 150 mm dia with presure control tube, nut bolt, socket, GI nipple with GM valve 150 mm dia etc complete work. Please Enable Macros to View BoQ information |
