|
| 1 | APPENDIX A - Maintenances of Existing 7 Sluices and 1 Box Culvert Manakatazham to Pulimukam Side and 2 shutter at bagavathimmodu |
| 2 | 60.1.2:RING BUND Type II Putting up ring bund with earth fille gunny bags of top width 1.0m bottom width 2.0m height 2.0 m side and filling in between with earth to form ring bund and maintaining the same leak proof till the completion of the work and clearing the site by dismantling the bund after completion of the work.etc.complete. |
| 3 | 60.2.3:Bailing out water using pump above 5 HP and Up to 10 HP-Bailing out water with engine and pump set above 5HP and up to 10HP, including conveyance to site and erection,cost of fuel, lubrication oil and other stores, pay of staff etc complete |
| 4 | 15.2.1:Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 5 | 4.1.8:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 6 | 5.1.3:Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 7 | 60.5.1:DOWEL BARS - Supplying and providing MS dowel bars of size 20 mm dia , 1.5m long (1m in rock and 0.5 m in concrete ) including drilling holes of 25mm dia and filling the gap with cement grout ( 0.25kg/each) etc complete |
| 8 | 5.22.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth levelThermo - Mechanically Treated bars of grade Fe-500D or more |
| 9 | 4.3.3:Centering and shuttering including strutting, propping etc. and removal of form work for:Columns, piers, abutments, pillars, posts and struts |
| 10 | 14.1.2:Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground within 50 meters lead:Cement mortar 1:4 ( 1 cement: 4 coarse sand) |
| 11 | APPENDIX B- Supply, Fabrication and Erection of MS and SS Embedded parts |
| 12 | OD42946/2025-2026:Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges |
| 13 | OD42963/2025-2026:Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges |
| 14 | 85.107:Supply of MS round bar including cost of conveyance charges |
| 15 | OD43184/2025-2026:Fabrication , erection and commissioning of Structural Steel Embedded parts in IS2062 Grade for Canal Shutters and accessories as per approved specifications, drawings and directions of deptl officer at site including cost of labour , machinery , incidental and handling charge etc complete but exculding cost of materials already supplied |
| 16 | OD43235/2025-2026:Fabrication, Supply, erection and assembling in correct position for Canal Shutter and alignment by welding SS Embedded parts in 304L Grade like roller track, seal track,Seal seat etc as per approved specifications, drawings and directions of deptl officer at site including cost of all materials,labour,machinery for planing, welding,shearing, grinding etc,lead and lift, conveyance, incidental and handling etc complete |
| 17 | 85.114:Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc on dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350 microns after cleaning the surface using hand and power tool cleaning including cost of all materials, labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site |
| 18 | APPENDIX C- Supply, Fabrication and Erection of Shutters |
| 19 | OD42565/2025-2026:Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges |
| 20 | OD42562/2025-2026:Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges |
| 21 | OD42567/2025-2026:Fabrication and supply of Structural Steel wheel gate for Canal Shutters and accessories as per approved specifications, drawings and directions of deptl officer at site including cost of labour , machinery , incidental and handling charge etc. complete but excluding cost of materials already supplied |
| 22 | 85.118:Supplying and fixing in correct position with specified initial interface L-type / bulb nose rubber seal confirming to IS11855 to the gates including cost of SS bolts and nuts and all labour and machinery and incidental and conveyance charges complete as per approved specifications and drawings |
| 23 | 85.116:Supplying and fixing in correct position with specified initial interface the flat type rubber seal confirming to IS 11855 to the gates including cost of SS bolts and nut all labour and machinery and incidental and conveyance charges complete as per approved specification and drawing |
| 24 | 85.114:Painting all the exposed surfaces of the gate and embedded parts with two coats of epoxy coal tar black paint confirming to IS14948 with a minimum film thickness of 150+/-5 microns per each coat over two coats of priming coat applied with zinc primer containing not less than 85% of zinc on dry film with a film thickness of 70+/-5 microns , so that the total film thickness of all coats including priming coat at any rate is not less than 350 microns after cleaning the surface using hand and power tool cleaning including cost of all materials, labour charges , cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site |
| 25 | OD43187/2025-2026:Erection (Canal Shutters) of the gates safely in the grooves, assembling and aligning including cost of all machinery, labour all incidental and conveyance charges etc complete as per direction of departmental officer at site |
| 26 | APPENDIX D- Supply, Fabrication and Erection of Shutter Hoisting Frameworks |
| 27 | OD43054/2025-2026:Supply of MS plates confirming to IS 2062GrB including cost of conveyance charges |
| 28 | OD43053/2025-2026:Supply of MS Tees, Angles, Joists, ISMB, ISMC confirming to IS2062GrA/B including cost of conveyance charges |
| 29 | OD43280/2025-2026:Fabrication and supply of Hoisting bride unit in structural steel confirming to IS2062 Gr including ladder, covers for hoisting unit etc as per approved specifications, drawings and directions of departmental officer at site including cost of labour, machinery, incidental and handling charges for fixing handrails and allied works etc complete but excluding material already supplied and weight of pipes for hand rails etc |
| 30 | 85.115:Cost of painting with 2 coats of enamel paint over 1 coat of zinchromate primer as per IS1477:1994 after hand and power tool cleaning including cost of all materials, labour charges, cost of testing all painting materials, all incidental charges, hire of T&P etc. complete as per the direction of department officers at site |
| 31 | OD43153/2025-2026:Supply of Bolt and nut up to 300mm length including cost of conveyance |
| 32 | 85.104:Supply of Al checquered plates including cost of conveyance charges |
| 33 | OD43155/2025-2026:Supply and fixing of 2ton 3meter heavy duty chain pulley block |
| 34 | OD43156/2025-2026:Supply and fixing of 3ton 3meter heavy duty chain pulley block |
| 35 | OD43154/2025-2026:Supply and fixing of link chain and shackle with the Pulley block and shutter Please Enable Macros to View BoQ information |
