|
| 1 | SH:- Earth work |
| 2 | Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers when required, into plinth, sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated soil as directed within a lead of 50m. |
| 3 | Re-filling excavated earth in foundations and plinth etc. in 15 cm layer including ramming and watering etc. complete. |
| 4 | Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete. |
| 5 | Random rubble masonry with hard stone in foundations and plinth in cement mortar 1 : 6 (1 cement : 6 fine sand) including levelling up with cement concrete 1 : 6 : 12 (1 cement : 6 coarse sand : 12 stone aggregate 20 mm nominal size) at plinth level. |
| 6 | SH:- CONCRETE WORK |
| 7 | Providing and laying cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) excluding the cost of centring an shuttering in Foundatiaon (colunm) |
| 8 | Providing and laying cement concrete 1 : 3 : 6(1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering in : (b) wall etc |
| 9 | Providing and laying damp proof course 50 mm thick with cement concrete 1 : 2 : 4 (1 cement : 2 coarse sand : 4 stone aggregate 20 mm nominal size). |
| 10 | SH:- REINFORCED CONCRETE WORK |
| 11 | Reinforced concrete work in foundations, footings, bases of columns etc. and mass concrete excluding cost of centring, shuttering and reinforcement in :a) 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size). |
| 12 | Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but exluding cost of centring, shuttering and reinforcement.a) 1 : 1.5 : 3 (1 cement : 1.5 corase sand : 3 stone aggregate 20 mm nominal size) |
| 13 | Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement. |
| 14 | Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement with 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 4 stone aggregate 20 mm nominal size). |
| 15 | Centring and shuttering including strutting, propping etc and removal of form work for :FOUNDATION PORTION |
| 16 | Centring and shuttering including strutting, propping etc and removal of form work forWALL PORTION |
| 17 | Centring and shuttering including strutting, propping etc and removal of form work for COLUNM PORTION |
| 18 | Centring and shuttering including strutting, propping etc and removal of form work for BEAM PORTION |
| 19 | Centring and shuttering including strutting, propping etc and removal of form work for SUSPENDED FLOOR |
| 20 | Reinforcement of RCC work including bending, binding and placing in position complete.b) Cold twisted bars. |
| 21 | SH:- BRICK WORKS |
| 22 | Half brick masonry (with best available local bricks) in cement mortar 1:3 (1 cement : 3 coarse sand) in foundation and plinth. |
| 23 | Extra for half brick masonry in superstructure above plinth level and up to floor two level. |
| 24 | SH:- WOOD WORKS |
| 25 | Providing approved best available local wood (Class - B II) work in frames of doors, windows clerestory windows and other frames, wrought framed and fixed in position. |
| 26 | Providing and fixing panelled, glazed or panelled and glazed shutters for doors, windows and clerestory windows including necessary iron butt hinges with necessary screws.a) 38 mm thick best available local wood, class - B I |
| 27 | Providing and fixing best available local wood glazed shutters for doors, windows and clerestory window using 7.5 kg/Sq.m. (3 mm thick glass panes) including black enamelled MS butt hinges with necessary screws. |
| 28 | Providing and fixing MS grills of required pattern in wooden frames of windows etc with MS flat, square or round bars with round headed bolts and nuts or by screws. b) Ornamental grill. |
| 29 | Providing and fixing aluminum sliding door bolts anodised transparent or dyed to required color or shade with nuts and screws etc complete.a) 300 x 16 mm |
| 30 | Providing and fixing aluminum Tower bolts anodized or transparent or dyed to required color or shade with necessary screws etc complete.a) Tower bolt 300 X 10 mm |
| 31 | Providing and fixing aluminum Tower bolts anodized or transparent or dyed to required color or shade with necessary screws etc complete.a) Tower bolt 150 X 10 mm |
| 32 | Providing and fixing aluminum 125 mm Handles anodised transparent or dyed to required color or shade with necessary screws etc complete. |
| 33 | Providing and fixing 300mm MS Hooks and Eyes. |
| 34 | Providing and fixing 40 x 3 mm flat iron hold fasts 40 cm long including fixing to frame with 10 mm dia bolts, nuts and wooden plugs and embedding in cement concrete block 30 x 10 x 15 cm in 1 : 3 : 6 (1 cement : 3 sand : 6 hard stone chips 40 mm nominal size). |
| 35 | SH:-FLOORING |
| 36 | 25 mm thick cement concrete flooring 1 : 2 : 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5 mm nominal size) finished with a floating coat of neat cement. |
| 37 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete |
| 38 | SH:- FINISHING |
| 39 | 12 mm cement plaster 1 : 3 (1 cement :3 fine sand). |
| 40 | 15 mm cement plaster 1 : 3 (1 cement :3 fine sand) on the rough side of single or half brick wall. |
| 41 | 20 mm cement plaster 1 : 3 (1 cement : 3 fine sand). Staircase |
| 42 | Applying priming coat with ready mixed pink primer of approved brand and manufacture on wood work complete. |
| 43 | Painting two or more coats (excluding priming coat) with superior ready mixed paint for wood work of approved brand and manufacture in all shades on new work to give an even shade. |
| 44 | Applying priming coat with readymixed genuine red lead paint of approved brand and manufacture on steel work |
| 45 | Painting two or more coats (excluding priming coat) with superior ready mixed paint for steel work of approved brand and manufacture in all shades on new work to give an even shade. |
| 46 | Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface :a)Water thinnable cement prime |
| 47 | Providing two coats of acrylic based wall putty/wall filler of Asian Paits/Berger/Dulux over concrete/ cement plaster/ brick walls and ceilings both internal and externalaf ter removing all the loosely adhering material from the wall/ceilings urface with the halp of emerystone,putty blade o rwire brush,moistening the wall with the help of sufficient quantity of clear water as specified and directed by the department. |
| 48 | Finishing walls with water proofing cement paint of required shade :a) New work (Two or more coats applied @ 3.84 kg/10 sqm) |
| 49 | SH:- MISCELLENEOUS |
| 50 | Making plinth protection 50 mm thick of cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 stone aggregate using 20 mm nominal size) over 75 mm bed of stone ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finsihing the top smooth. |
| 51 | Providing and fixing 40 mm dia GI Pipe outlet in cement mortar 1 : 3 (1 cement : 3 fine sand) including cutting and making good the wall. |
| 52 | SH:-DRAIN WORK |
| 53 | Construction of cement concrete drain 15 cm wide and 15 cm deep in cement concrete 1 : 3 : 6 (1 cement : 3 sand : 6 hard graded stone chips or shingle 40 mm and down gauge) 8 cm thick on sides and bottom and plastering and all exposed surfaces with 12 mm thick cement mortar 1 : 3 (1 cement : 3 coarse sand) including shuttering complete. |
| 54 | Construction of cement concrete drain 30 cm wide and 23 cm deep in cement concrete 1 : 3 : 6 (1 cement : 3 sand : 6 hard graded stone chips/shingle 40 mm and down gauge) 8 cm thick on sides and bottom and plastering on all exposed surfaces with 12 mm thick cement mortar1 : 3 (1 cement : 3 fine sand) including shuttering complete. |
| 55 | Providing laying and jointing glazed stone ware pipe grade 'A' with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete.a) 100 mm dia SW pipes |
| 56 | Providing and laying cement concrete 1 : 4 : 8(1 cement : 4 lime sand : 18graded stone aggregate 40 mm nominal size) all around SW Pipe including bed concrete 15 cm thick as per standard design. a) 100 mm dia SW pipes |
| 57 | SH:WATER SUPPLY |
| 58 | Providing and fixing Chlorinated Polyvinyl Chloride(CPVC) pipes,having thermal stability for hot&cold water supply, including all CPVC plain&brass threaded fittings, including fixing the pipe with clamps at 1.00m spacing.This includes jointing of pipes&fittings with one step CPVC solvent cement and testing of joints complete as per directionof Engineer in Charge.a) 20 mm nominal outer dia Pipe |
| 59 | Providing and fixing Chlorinated Polyvinyl Chloride(CPVC) pipes,having thermal stability for hot&cold water supply, including all CPVC plain&brass threaded fittings, including fixing the pipe with clamps at 1.00m spacing.This includes jointing of pipes&fittings with one step CPVC solvent cement and testing of joints complete as per directionof Engineer in Charge.b) 25 mm nominal outer dia Pipe |
| 60 | Providing and fixing Chlorinated Polyvinyl Chloride(CPVC) pipes,having thermal stability for hot&cold water supply, including all CPVC plain&brass threaded fittings, including fixing the pipe with clamps at 1.00m spacing.This includes jointing of pipes&fittings with one step CPVC solvent cement and testing of joints complete as per directionof Engineer in Charge.c) 40 mm nominal outer dia Pipe |
| 61 | Providing and fixing CP brass long body bib cock of approved quality. Confirming to IS Standard and weiging not less 810 gma) 15 mm nominal bore |
| 62 | Providing and fixing CP brass stop cock( concealed) of approved quality. Confirming to IS Standard and weiging not less 810 gma) 15 mm nominal bore |
| 63 | Providing and fixing CP brass angle valve for basin/ maixer Gzeyser point etc of approved quality. Confirming to IS Standard a) 15 mm nominal bore |
| 64 | Providing and fixing PVC connection pipe with brass union.a) 15 mm nominal bore |
| 65 | Providing and fixing PVC connection pipe with brass union.a) 20 mm nominal bore |
| 66 | Providing and fixing PVC connection pipe with brass union.a) 25 mm nominal bore |
| 67 | Providing and fixing non-return valve of approved quality.b) 32 mm nominal bore |
| 68 | Providing and fixing ball valve (brass) of approved quality complete.A) High pressure with copper floats( a) 15mm nominal bore |
| 69 | Providing and fixing ball valve (brass) of approved quality complete.A) High pressure with copper floats b) 250mm nominal bore |
| 70 | SH:SANITARY INSTALLATION |
| 71 | Providing and fixing white vitreous china water closet squating pan (Indian type WC pan) size 580 mm with 100 mm and sand cast iron P or S trap, 12.5 Litre high level CI flushing cistern (of approved make) with fittings RS or CI brackets, 32 mm dia galvanized steel telescopic flush pipe with fittings and clamps 20 mm GI over flow pipe with specials and mosquito proof coupling of approved municipal design and GI chain and pull complete including painting of cistern and fittings, cutting and making good the walls and floors where required.a) Long Pan patten WC Pan |
| 72 | Providing and fixing white vitreous china pedestal type (European type WC pan) water closet with seat and lid with CP brass hinges and rubber buffers, 12.5 Litres white vitreous china low-level flushing cistern with fittings and brackets 40 mm white porcelain in enamel led flush band, 20 mm over flow pipe with specials and mosquito proof coupling of approved municipal design complete including cutting and making good the walls and floors where required.a) WC pan with white plastic seat and lid. |
| 73 | Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x430x265 mm sizes respectively with CI automatic flushing cistern with fittings, RS or CI brackets standard size galvanized steel flush pipe and spreaders with brass unions and GI clamps complete including painting of cistern and fittings, cutting and making good the walls and floors where required. |
| 74 | Providing and fixing white vitreous china wash basin with RS or CI brackets painted white 15 mm CP brass pillar taps and CP brass chain with rubber plug 32 mm CP brass waste of standard pattern, 32 mm dia CP brass trap and MI unions complete, including cutting and making good the walls where required.b) Flat back wash basin size 550x400 mm with single 15 mm CP brass pillar taps of heavy quality. |
| 75 | Providing and fixing a pair of white vitreous china foot rest of standard pattern for squatting pan WC.a) 250 x 130 x 30 mm |
| 76 | Providing and fixing 100 mm sand cast iron grating for gulley, floors or nahni trap. |
| 77 | Providing and fixing 600x450 mm bevelled edge mirror or superior glass (of approved quality) complete with 6 mm thick asbestos sheet ground fixed to wooden cleadt with CP brass screws and washers. |
| 78 | Providing and fixing 600 x 120 mm glass shelf with CP brass brackets and guard rail complete, fixed to wooden cleadts with CP brass screws. |
| 79 | Providing and fixing CP brass towel rail complete with CP brass brackets fixed to wooden cleadt with CP brass screws (heavy quality).a) 750 x 20 mm size |
| 80 | Providing and fixing toilet paper holder.a) CP Brass |
| 81 | Providing best available local wood 50 x 50 x 50 mm wood plugs including cutting brick work and fixing in cement mortar 1:3 (1 cement : 3 fine sand). |
| 82 | Providing and fixing sand cast iron/ cast iron (spun) soil, waste and vent pipes.c) 100 mm dia |
| 83 | Providing and fixing sand cast iron heel rest sanitary bend.a) 100 mm dia |
| 84 | Providing and fixing sand cast iron single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.a) 100 x 100 x 100 mm |
| 85 | Providing and fixing sand cast iron trap of self cleadnsing design with sand cast iron screwed down or hinged grating with or without vent arm complete including cost of cutting and making good the walls and floors.c) 100 mm inlet and 50 mm outlet |
| 86 | Providing and fixing structural steel work in single sections (Rolled Steel Joists), including cutting, hoisting, fixing in position and applying one coat of red oxide / red lead primer complete.(Structural Steel Work in Rolled Steel Sections (RSJ/UB/UC) |
| 87 | Providing and fixing in position collapsible steel shutters with vertical channels 20 mm x 10 mm x 2 mm and braced with flat iron diagonals 20 mm x 5 mm size with top and bottom rails of T iron 40 mm x 40 mm x 6 mm with 38 mm dia steel pulleys complete with bolts, nuts, locking arrangements, stoppers, handles including applying a priming coat of red lead paint. |
| 88 | Providing corrugated G.I.sheet roofing fixed with galvanised iron J or L hooks, bolts & nuts 8 mm dia with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead complete, excluding the cost of purlins, rafters and trusses.a) 0.80 mm thick GI sheet |
| 89 | SERVICE PORTION |
| 90 | INTERNAL ELECTRICAL WIRING:- Providing and fixing point wiring with PVC insulated copper cables, drawn in heavy gauge PVC conduit, including accessories like junction boxes and inspection boxes, as per IS specifications |
| 91 | ELECTRICAL FITTINGS & ACCESSORIES: - Supply and installation of approved electrical fittings like LED luminaires, ceiling fans, switches, socket outlets, and MCBs, including connections, testing, and commissioning as per standards |
| 92 | MAIN SWITCH, DISTRIBUTION BOARD & SERVICE CONNECTION: - Supply and installation of main switch, MCCB/MCB, main distribution board, energy meter, and service cable, including testing, commissioning, and earthing arrangements as required. |
| 93 | EARTHING SYSTEM: - Providing and laying earthing system with earth electrode, pit chamber, and continuity conductor, including connections and testing to ensure proper earth resistance as per IS standards. Please Enable Macros to View BoQ information |
