|
| 1 | Dismantling of existing structures like culverts, bridges, retaining walls and other structure comprising of masonry, cement concrete, steel work, including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceable material and stacking the serviceable material with all lifts and lead of 1000 m as per Technical Specifications Clause 202 for Rural Roads of MORD. |
| 2 | By Manual Means |
| 3 | Cement Concrete |
| 4 | Dismantling Brick/Tile Work Dismantling of existing structures like culverts, bridges, retaining walls and other structures comprising of brick masonry, including disposal of unserviceable material and stacking the serviceable material with all lift and lead of 1000 m as per Technical Specifications Clause 202 for Rural Roads of MORD. |
| 5 | Cement mortar |
| 6 | Taking out sluice gate draw shutter gearing arrangements & pedestal including refitting the same with new nuts & bolts where necessary. |
| 7 | Up to 4 sqm. |
| 8 | Taking out only. |
| 9 | Taking out runner of any section including cutting bolts and nuts, dismantling existing concrete or brickwork where necessary. |
| 10 | Earth work from borrow pits over existing embankment or for repairs to embankment, closing breaches etc. with in an initial lead of 30 metre and lift of 1.50metre including breaking clods and depositing the same in layers not exceeding 25cm. and rough dressing etc. complete as per profile. |
| 11 | Earth work in excavation of foundation of structures as per drawing and technical specification, including setting out, removing, spreading or stacking of spoils within a lead of 150 m. as directed and including trimming the sides of the trenches, leveling, dressing and ramming the bottom, and backfilling with approved material complete as per direction of the Engineer-in-Charge . I. In all sorts of soil excluding marshy soil & rocks (soft or hard) by manual means. |
| 12 | upto 3 m depth |
| 13 | Without pumping out water and shoring |
| 14 | Sand filling in foundation trenches and at the back of abutments, wing-walls etc. with good local sand free from earth in layers not exceeding 15 cm. including inundating each layer by profuse water and poking and ramming layer by layer complete including supply of sand. Quality of sand is to be approved by the Engineer-in-charge. |
| 15 | Ordinary Cement concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement if any, in ground floor as per relevant lS codes. |
| 16 | Pakur Variety |
| 17 | First class Brick work in cement sand mortar in steining of well, pier, abutment, wing wall, parapets cross drain. H.P. culverts, guard wall etc. including curing, scaffolding, raking out joints etc. complete including cost and carriage of all materials. |
| 18 | In 1:4 proportion. |
| 19 | Supplying,fitting and fixing of Mild Steel Guide Channel with necessary Mild Steel lugs of required length and size by making hole in to wall and fixing with necessary masonry work with maintaining proper line and levelas directed by the Engineer-in-charge. This item includes two coats of anti-corrossive bituminous paint over two coats of red lead primer. Payment will be made on actual length of Guide Channel. |
| 20 | Supplying /Replacing at site new pedestal or other similar items for sluices made with Mild Steel plates, angles, channels , holding down nuts & bolts etc. including fitting, fixing in position in concrete or masonry complete as per direction of the Engineer - in -charge. |
| 21 | Supplying, fitting, fixing Mild Steel draw shutter with Mild Steel plate of thickness as specified by the Engineer-in-charge and other necessary Mild Steel sections for sluice including fabricating the same (as per draw in gandinstruction given by the Engineer-in-charge) excluding cost of Mild Steel guide channel, sillbeam, gearing arrangement etc. but including painting with two coats of anti corrosive bituminous paint of approved make & brand over two coat of red lead primer and with necessary masonry work with all materials supply etc. complete at site. |
| 22 | Supplying, fitting & fixing in position rubber seal arrangements with musical note harmonic 'J' type for making water tight in both up and down stream of draw shutter as wellas flap shutter including guide paths, additional M.S. flats, bolts and nuts for fixing the rubber seal in position including fabrication cost and carriage of all materials to site and complete as per direction of the Engineer-in-charge. |
| 23 | Musical Note, Harmonic Type |
| 24 | 127 mm x 6 mm |
| 25 | Supplying /Replacing Gear rod by a new Mild Steel Gear rod, threaded length as required and fitting,fixing in position with screw gearing arrangement for operating the draw shutter including taking out old gear rod by cutting bolts etc. complete as per direction of the Engineer-in-charge. (The old materials to be returned to Departmental Godown.) |
| 26 | 65 mm Dia |
| 27 | Supplying / Replacing at site alloy steel bush for gearing arrangement of Mild Steel regulator shutter including fitting & fixing the same in Cast Iron wheel with bearing and necessary lubricant including cutting internal thread in the bushas necessary including cost of all materials, tools, labours and carriage to site complete of specified diameter as per direction of the Engineer - in - charge. |
| 28 | 65 mm. dia |
| 29 | Supplying, fitting & fixing Cast Iron wheel (after taking out existin gone if necessary), rimmade of 28mm. to 36mm. dia to fit any size of gear rod including carriage to site, painting with two coats of bituminous paint over two coats of red lead primer etc .complete as per direction of the Engineer-in-charge. |
| 30 | 60 cm Dia CI Wheel |
| 31 | Painting on steel or other metal surface with any approved bituminous anticorrosive paint after preparing the surface including removing paints,cleaning,smoothening etc.including scaffolding where necessary including cost of all materials complete |
| 32 | Two coat |
| 33 | Painting with ready mixed red lead paint of approved make and brand : |
| 34 | Two coats |
| 35 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throatins, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface] |
| 36 | With 1:6 cement mortar |
| 37 | 20 mm thick plaster |
| 38 | Applying decorative cement based paint of approved quality after preparing the surface including scraping the same thoroughly (plastered or concrete surface) as per manufacturer's specification |
| 39 | Earth work in filling in foundation trenches or plinth with good earth, in layers not exceeding 150 mm. including watering and ramming etc. layer by layer complete. (Payment to be made on the basis of measurement of finished quantity of work) |
| 40 | With earth obtained from excavation of foundation. Please Enable Macros to View BoQ information |
