|
| 1 | Supply, install, commissioning & testing of Motor Control Panel \"out-door type\" of size 900 mm (height) x 900 mm (breadth) x 500 mm (depth) (minimum dimensions) factory fabricated CPRI approved (type-tested) with suitable neoprene rubber gasket to make it completely dust & vermin proof & degree of protection not less than IP-55 & general construction confirming to IS-13947, double door, front & back openable. The panel shall be provided with ventilation facility in the form of louvers for better heat dissipation & tinned copper bus-bar wrapped with coloured PVC tape/sleeves of rating in conformity to the Incoming MCCB/MCB rating. The panel board shall be fabricated out of 3.15 mm thick (for outer portions) & 2.0 mm thick (for inner portions) CRCA sheet duly pre-treated & powder coated, supporting angle iron frame & MC channel base suitable for 3 Ph, 4 wire system 415/440 volts grade incl complete internal wiring with not less than 2.5 sqmm copper wire incl cable glands of suitable sizes incl suitable PCC (1:3:6) type C-2 foundation , necessary earthwork (if any) incl taking down old unsv one complete all as specified & as directed & to the entire satisfaction of the Engr-In-Charge with & incl the following accessories : [ For Watch Tower Borewells ] |
| 2 | BUS-BAR & INTERNAL CONNECTIONS :The bus-bars shall be made up of 04 Nos high grade Aluminium 100 A rated, duly insulated with 1100 V grade standard colour coded PVC sleeves & rigidly mounted on suitable sized \"F\" class insulators of non-hygroscopic, non-combustible, all internal connections from main bus-bars to switch gears etc.PROVISION FOR CABLE ENTRY :The provision for cable entry/exit shall be provided in the bottom for both incoming & out-going cables with the help of glands matching the existing LT cable sizes.INCOMING :(a) MCCB 4P (Ics = 100% Icu) with thermal magnetic release, adjustable short circuit & adjustable overload setting,suitable for isolation, having breaking capacity 25 KA & of rating 20 to 32 A - 01 Nos. Make : Cat No : DZ0F0020-32CXC1AOOOO of Make L&T or techno-commercially equivalent of LEGRAND/SIEMENS.OUTGOINGS :(a) MCB, SPN, 10KA, 230V, \"C\" curve, 06-32 A, ISI marked - 03 Nos (2W + 1S). Make : LEGRAND/ABB/SIEMENS(b) Single Phase DOL Starter perfectly suitable for Submersible Pumping Set of capacity upto 2 HP, conforming to IS/IEC : 60947-4-1, IP-54, with & incl Extended wide band coil, FRLS Copper Internal Wiring, Starter Type - Air Break, Class-H Insulation with Contactor Rating - 12A, Overload Relay Range - 2.8A to 4.2A incl testing complete. Make : SIEMENS/L&T/HAVELLS/BCH - 02 Nos (1W + 1S)INSTRUMENTATION SYSTEM :(a) Digital type Multi-Function meter with built in selector Switch & 03 Nos CTs matching with the I/C breaker, Accuracy Class - 1.0, 3 phase, Size 96 x 96 mm. Make : Cat No WL411010OOOO of make L&T or techno-commercially equivalent of ELMEASURE/SECURE.(b) Indicator lamp with integral circuit (230/240V) & cluster LED (Red, Orange, Blue) - 01 Set.(c) Danger notice plate of size 20 x 15 cm of 1.6mm thick mild-steel sheet, vitreous enamelled white, with letters, figures and conventioinal skul and bones in signal-red colour and fixed with MS clamps, bolts and nuts of approved size, for LT conforming to IS-2551 - 02 Nos (Front & Back). |
| 3 | Supply, install, commissioning & testing of Motor Control Panel \"out-door type\" of size 1200 mm (height) x 1000 mm (breadth) x 600 mm (depth) (minimum dimensions) factory fabricated CPRI approved (type-tested) with suitable neoprene rubber gasket to make it completely dust & vermin proof & degree of protection not less than IP-55 & general construction confirming to IS-13947, double door, front & back openable. The panel shall be provided with ventilation facility in the form of louvers for better heat dissipation & tinned copper bus-bar wrapped with coloured PVC tape/sleeves of rating in conformity to the Incoming MCCB/MCB rating. The panel board shall be fabricated out of 3.15 mm thick (for outer portions) & 2.0 mm thick (for inner portions) CRCA sheet duly pre-treated & powder coated, supporting angle iron frame & MC channel base suitable for 3 Ph, 4 wire system 415/440 volts grade incl complete internal wiring with not less than 2.5 sqmm copper wire incl cable glands of suitable sizes incl suitable PCC (1:3:6) type C-2 foundation , necessary earthwork (if any) incl taking down old unsv one complete all as specified & as directed & to the entire satisfaction of the Engr-In-Charge with & incl the following accessories : [ For Other Borewells ] |
| 4 | BUS-BAR & INTERNAL CONNECTIONS :The bus-bars shall be made up of 04 Nos high grade Aluminium 100 A rated, duly insulated with 1100 V grade standard colour coded PVC sleeves & rigidly mounted on suitable sized \"F\" class insulators of non-hygroscopic, non-combustible, all internal connections from main bus-bars to switch gears etc.PROVISION FOR CABLE ENTRY :The provision for cable entry/exit shall be provided in the bottom for both incoming & out-going cables with the help of glands matching the existing LT cable sizes.INCOMING :(a) MCCB 4P (Ics = 100% Icu) with thermal magnetic release, adjustable short circuit & adjustable overload setting,suitable for isolation, having breaking capacity 25 KA & of rating 40 to 50 A - 02 Nos. Make : Cat No : DZ0F0050CXC1AOOOO of Make L&T or techno-commercially equivalent of LEGRAND/SIEMENS.(b) Compact Enclosed ATS (Automatic Transfer Switch) suitable for inside panel mounting & I-O-II operation, 4 Pole, 63 A, confirming to IEC 60947-6-1 - 01 No complete with following features/specifications : (i) Double-Break Contact System offering High Short-time Withstand.(ii) Ample Space for Cable Termination.(iii) Ease of Generator Control (ON-OFF, Cooling Cycle Self-Test).(iv) Cyclic Event Logger.(v) Priority Source Selection.(vi) Adjustable Time Delay (0.1 Sec to 3 Hrs).(vii) Suitable for 3-Phase as well as 1-Phase sources.(viii) Protections - UV/OV, Phase Sequence, Single Phasing, Frequency.(ix) Terminal Shrouds, Phase Barriers & Source Separator etc.Cat No : 1SYN151254R1001 of make ABB or techno-commercially equivalent of L&T/Siemens. |
| 5 | OUTGOINGS :(a) MCB, TPN, 10KA, 415V, \"C\" curve, 40-63 A, ISI marked - 03 Nos (2W + 1S). Make : LEGRAND/ABB/SIEMENS(b) Three Phase Fully Automatic Starter perfectly suitable for Submersible Pumping Set of capacity upto 15 HP, conforming to IS/IEC : 60947-4-1, IP-54, with & incl Single Phasing Protection (SPP) with Auto Manual Switch, FRLS Copper Internal Wiring, Combined V / A Meter, Voltmer Selector Switch, ON / OFF Indication, Star-Delta Timer etc., Class-H Insulation with Contactor Rating AC3 (A) - 20A, Overload Relay Range - 13.2A to 20A incl testing complete. Make : SIEMENS/L&T/HAVELLS/BCH - 02 Nos (1W + 1S)INSTRUMENTATION SYSTEM :(a) Digital type Multi-Function meter with built in selector Switch & 03 Nos CTs matching with the I/C breaker, Accuracy Class - 1.0, 3 phase, Size 96 x 96 mm. Make : Cat No WL411010OOOO of make L&T or techno-commercially equivalent of ELMEASURE/SECURE.(b) Indicator lamp with integral circuit (230/240V) & cluster LED (Red, Orange, Blue) - 01 Set.(c) Danger notice plate of size 20 x 15 cm of 1.6mm thick mild-steel sheet, vitreous enamelled white, with letters, figures and conventioinal skul and bones in signal-red colour and fixed with MS clamps, bolts and nuts of approved size, for LT conforming to IS-2551 - 02 Nos (Front & Back).NOTE: 1) Design / drawing / BOM of the Panel Board incl all accessories showing the dimensions is to be obtained from the Manufacturer / Supplier & is to be got approved from the Engr-In-Charge & GE before placing final order to the manufacturer.2) Anything missed out in the technical specifications but technically required for efficient working is deemed to be included in the quoted rates.3) The electrical connection of digital Multi Functional Meter in the MCC panel is to be done from load side so that monitoring of various parameters viz. Voltage, Current, KW, KVA, power factor, frequency etc. can be done for both SEB mains & DG mains.4) Necessary PCC foundation/plinth shall be as per the recommendations of OEM / Supplier etc. & cost of the same is deemed to be included in the quoted rates. |
| 6 | M&L for development / flushing of tube / bore wells with air compressor of suitable capacity till sand / mud free water of potable quality is obtained & to achieve minimum discharge capacity of 24000 LPH or as directed by the Engr-In-Charge based on size / type of borewells (Compressor with accessories & tube etc. shall be arranged by the contractor) complete all as specified & as directed & to the entire satisfaction of Engr-In-Charge. |
| 7 | NOTE : (i) Quoted rate is deemed to be inclusive of hire as well as transportation cost of Compressor with allied accessories, Tripod, Chain Pulley etc. for the said job.(ii) Quoted rate is deemed to be inclusive of taking down of the existing column pipes, submersible pump & connected items & refixing / installation of the same incl testing after the complete development / flushing process.(iii) The contractor / firm is required to visit the proposed sites of borewells prior to quoting of the subject items/ work so as to ascertain the actual ground requirements. Any further query at a later date shall not be entertained & responsibility of the same shall rest on the contractor/ firm.(iv) Anything missed out in the technical specifications but technically required for efficient working is deemed to be included in the quoted rates. |
| 8 | M&L for Submersible cable, PVC insulated, PVC sheathed 1100 volts grade, multistranded copper conductor, flat, 3 core, 4.0 Sqmm incl testing & taking down old unsv one etc. complete all as specified and as directed & to the entire satisfaction of Engr-In-Charge. Make : Havells/Polycab/Finolex/KEI |
| 9 | M&L for Submersible cable, PVC insulated, PVC sheathed 1100 volts grade, multistranded copper conductor, flat, 3 core, 6.0 Sqmm incl testing & taking down old unsv one etc. complete all as specified and as directed & to the entire satisfaction of Engr-In-Charge. Make : Havells/Polycab/Finolex/KEI |
| 10 | S&F Gun Metal Non Return Valve, ISI marked with flanged and connecting to GI pipe of size 32 mm bore including jointing materials, nuts, bolts, washers and necessary accessories incl testing & taking down old unsv one etc. complete all as specified and as directed & to the entire satisfaction of Engr-In-Charge. Make : Kirloskar/Leader/Upadhyay/Kartar/RMCO |
| 11 | S&F Gun Metal Non Return Valve, ISI marked with flanged and connecting to GI pipe of size 50 mm bore including jointing materials, nuts, bolts, washers and necessary accessories incl testing & taking down old unsv one etc. complete all as specified and as directed & to the entire satisfaction of Engr-In-Charge. Make : Kirloskar/Leader/Upadhyay/Kartar/RMCO |
| 12 | S&F Gun Metal Gate Valve conforming to IS 781 -1984 with iron wheelhead screwed both ends for iron pipe of size 32 mm bore incl necessary jointing materials, connected fittings (if any reqd at site) etc. & testing incl taking down old unsv one complete all as specified & a directed and to the entire satisfaction of the Eng-in-Charge. MAKE : Leader/Tata/Zoloto/Kartar/RMCO |
| 13 | S&F Gun Metal Gate Valve conforming to IS 781 -1984 with iron wheelhead screwed both ends for iron pipe of size 50 mm bore incl necessary jointing materials, connected fittings (if any reqd at site) etc. & testing incl taking down old unsv one complete all as specified & a directed and to the entire satisfaction of the Eng-in-Charge. MAKE : Leader/Tata/Zoloto/Kartar/RMCO |
| 14 | S&F Bib Taps, Cast Copper Alloy with crutch or butterfly handle, screwed down, screwed for iron pipe of size 15 mm bore incl necessary jointing materials, connected fittings (if any reqd at site) etc. & testing incl taking down old unsv one complete all as specified & a directed and to the entire satisfaction of the Eng-in-Charge. |
| 15 | M&L for galvanised steel water tubing, medium grade, 32 mm bore with all running fittings such as bends, tees, unions, elbows, connecting pieces etc. laid in trenches or on ground/other surface etc. incl testing complete all as specified and to the entire satisfaction of the Eng-in-Charge. MAKE : Tata/Jindal/Prakash. |
| 16 | M&L for galvanised steel water tubing, medium grade, 50 mm bore with all running fittings such as bends, tees, unions, elbows, connecting pieces etc. laid in trenches or on ground/other surface etc. incl testing complete all as specified and to the entire satisfaction of the Eng-in-Charge. MAKE : Tata/Jindal/Prakash. |
| 17 | Testing of Water samples for Physical, Chemical & Bacteriological analysis from any Govt. approved / NABL accredited Laboratory as approved by the GE/Engr-In-Charge. NOTE : The cost of collection of sterilized bottles, collection of water samples from water sources as directed by GE / Engr-In-Charge, depositing to laboratory and submitting the test results duly signed & certified to the Engr-In-Charge complete is deemed to be included in the unit quoted rates. |
| 18 | Supply and laying in trenches/through pipes or bare in road crossings/ paths /drains /ducts /floors /along poles/ walls/ ceilings/ equipments etc. Cable Under ground, armoured, XLPE insulated with stranded aluminium conductor, 1100 Volts grade ofcross sectional area, 4.0 Core 10 Sqmm incl connecting with suitable glands, lugs etc. with & incl necessary fixing arrangements incl taking down old unsv one complete all as specified and directed & to the entire satisfaction of the Engr-in-Charge. Make: Havells/Finolex/Polycab/Gloster |
| 19 | Supply and laying in trenches/through pipes or bare in road crossings/ paths /drains /ducts /floors /along poles/ walls/ ceilings/ equipments etc. Cable Under ground, armoured, XLPE insulated with stranded aluminium conductor, 1100 Volts grade ofcross sectional area, 4.0 Core 25 Sqmm incl connecting with suitable glands, lugs etc. with & incl necessary fixing arrangements incl taking down old unsv one complete all as specified and directed & to the entire satisfaction of the Engr-in-Charge. Make: Havells/Finolex/Polycab/Gloster |
| 20 | Supply, Install, Commissioning & Testing of Submersible Pumping Set, electric driven, 3 Phase, suitable for 250 / 200 / 150 mm dia borewell (casing pipe of 250 / 200 / 150 mm dia) with & including High Quality Pump Oil Seal, High Grade SS Pump Casing, SS-410 Pump Shaft, SS Impeller, Head 100 Mtr, Discharge 600-650 LPM, not less than 10 HP Motor,Dynamically Balanced Rotor, High Quality SS Motor Body, Low Watt Loss Stamping Motor Stator, PVC Coated Copper Winding, Delivery Pipe Size 65/50 mm, CED Coated CI Parts, Operating Voltage Range 350V to 440V & 01 Year OEM Warranty complete incl connected items incl taking down old unsv ones & depositing the same to the MES Storeyard complete all as specified and to the entire satisfaction of the Engr-In-Charge. Make : Kirloskar / KSB / CG / Havells |
| 21 | Supply, Install, Commissioning & Testing of Submersible Pumping Set, electric driven, 3 Phase, suitable for 250 / 200 / 150 mm dia borewell (casing pipe of 250 / 200 / 150 mm dia) with & including High Quality Pump Oil Seal, High Grade SS Pump Casing, SS-410 Pump Shaft, SS Impeller, Head 100 Mtr, Discharge 500-600 LPM, not less than 3 HP Motor, Dynamically Balanced Rotor, High Quality SS Motor Body, Low Watt Loss Stamping Motor Stator, PVC Coated Copper Winding, Delivery Pipe Size 65/50 mm, CED Coated CI Parts, Operating Voltage Range 350V to 440V & 01 Year OEM Warranty complete incl connected items incl taking down old unsv ones & depositing the same to the MES Storeyard complete all as specified and to the entire satisfaction of the Engr-In-Charge. Make : Kirloskar / KSB / CG / Havells |
| 22 | Supply, Install, Commissioning & Testing of Submersible Pumping Set, electric driven, 1 Phase, suitable for 250 / 200 / 150 mm dia borewell (casing pipe of 250 / 200 / 150 mm dia) with & including High Quality Pump Oil Seal, High Grade SS Pump Casing, SS-410 Pump Shaft, SS Impeller, Head 80 Mtr, Discharge 120-150 LPM, not less than 1.5 HP Motor,Dynamically Balanced Rotor, High Quality SS Motor Body, Low Watt Loss Stamping Motor Stator, PVC Coated Copper Winding, Delivery Pipe Size 32 mm, CED Coated CI Parts, Operating Voltage Range 160V to 240V & 01 Year OEM Warranty complete incl connected items incl taking down old unsv ones & depositing the same to the MES Storeyard complete all as specified and to the entire satisfaction of the Engr-In-Charge. Make : Kirloskar / KSB / CG / Havells |
| 23 | IMPORTANT NOTE : 1) Design / Drawing / Technical specifications etc. of the complete Submersible Pumping Set is to be obtained from OEM / Auth Supplier / Dealer strictly keeping in view the actual ground / site requirement & the same is to be got approved from Engr-In-Charge & GE before placing final order to the manufacturer.2) Anything missed out in the technical specifications but technically required for efficient working is deemed to be included in the quoted rates.3) PVs & Test / Guarantee / Warantee Certificates to be submitted in Original to the Engr-In-Charge for checking & records. |
| 24 | Excavation in trenches by mechanical or other means n.exc 1.5m wide and n.exc 1.5m in depth for laying of pipe and getting out in hard dense soil old unsv Cables/Pipes incl connected items complete all as specified and as directed. |
| 25 | Returning, filling in including spreading, levelling, watering and well ramming in layers n.exc 25cm thick. |
| 26 | Removing of excavated material n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point. |
| 27 | S&F Steel wire rope of size 4 mm to tie the Submersible P/Set with the top casing pipe to prevent immersion under water with suitable sized MS Clamps, nuts, bolts, washers etc. complete all as specified and as directed & to the entire satisfaction of the Engr-in-Charge. |
| 28 | M&L for HDPE DWC (Double Wall Corrugated) Pipe of rating 450 N, ISI marked with Min OD 63 mm & Min ID 50 mm, Orange colour for LT UG Cable protection with & including Couplers with rubber rings & RR & NFP properties/features confirming to IS 16205 Part 24:2018 & IEC 61386 Part 24:2007 complete all as specified & as directed by the Engr-In-Charge. Make : Astral / Supreme / Finolex / Polycab |
| 29 | M&L for earthing complete with Galvanised steel earth plate electrode 600 x 600 x 6 mm thick buried directly in ground (in vertical position) earth pit not less than 2.25 mtr below normal ground level with the top edge of the earth plate not less than 1.5 mtr (B.G.L.) and connected to GI earth strip 32 x 6 mm by means of bolts, nuts, check nuts, and washers of galvanized iron including PCC pit & cover with suitable handle, including necessary excavation and earth work in any type of soil, 20 mm dia med grade galvanized steel tube for watering with one end fixed with suitable funnel and wire mesh, 40 mm bore medium grade galvanized steel tubing for drawing earth lead GI strip protection & common salt, charcoal in alternate layers etc. complete all as shown in EP No 3 of SSR Part 1 and testing on completion incl taking down old unsv earthing assy complete all as specified and as directed by the Engr-in-Charge. Make of GI Pipe : Tata / Jindal / Prakash |
| 30 | IMPORTANT NOTES : 1) On completion of the complete work/job the Contr is to perform earth resistance tests for each earthing job in the presence of the Engr-In-Charge or his rep & submit test certificates duly signed & certified. If the test results are not satisfactory or not within the permissible limits of 1.0 Ohm then the job is to be redone without any extra cost to the Dept till the results are satisfactory.2) Cost of GI Earth Strip and GI Protection Pipe upto 7.5 mtr length & welding/brazing work is deemed to be included in the unit quoted rates.3) Cost of Wire Mesh, Funnel, Earthwork, PCC Chamber with Cover, Test Point etc.is deemed to be included in the unit quoted rates. |
